[PATCH v9 2/3] pwm: Add Allwinner's D1/T113-S3/R329 SoCs PWM support
Uwe Kleine-König
u.kleine-koenig at baylibre.com
Mon Jul 8 07:46:42 PDT 2024
On Mon, May 20, 2024 at 09:42:20PM +0300, Aleksandr Shubin wrote:
> Allwinner's D1, T113-S3 and R329 SoCs have a quite different PWM
> controllers with ones supported by pwm-sun4i driver.
>
> This patch adds a PWM controller driver for Allwinner's D1,
> T113-S3 and R329 SoCs. The main difference between these SoCs
> is the number of channels defined by the DT property.
>
> Co-developed-by: Brandon Cheo Fusi <fusibrandon13 at gmail.com>
> Signed-off-by: Brandon Cheo Fusi <fusibrandon13 at gmail.com>
> Signed-off-by: Aleksandr Shubin <privatesub2 at gmail.com>
> ---
> drivers/pwm/Kconfig | 10 +
> drivers/pwm/Makefile | 1 +
> drivers/pwm/pwm-sun20i.c | 387 +++++++++++++++++++++++++++++++++++++++
> 3 files changed, 398 insertions(+)
> create mode 100644 drivers/pwm/pwm-sun20i.c
>
> diff --git a/drivers/pwm/Kconfig b/drivers/pwm/Kconfig
> index 4b956d661755..d2e0a080eb3c 100644
> --- a/drivers/pwm/Kconfig
> +++ b/drivers/pwm/Kconfig
> @@ -625,6 +625,16 @@ config PWM_SUN4I
> To compile this driver as a module, choose M here: the module
> will be called pwm-sun4i.
>
> +config PWM_SUN20I
> + tristate "Allwinner D1/T113s/R329 PWM support"
> + depends on ARCH_SUNXI || COMPILE_TEST
> + depends on COMMON_CLK
> + help
> + Generic PWM framework driver for Allwinner D1/T113s/R329 SoCs.
> +
> + To compile this driver as a module, choose M here: the module
> + will be called pwm-sun20i.
> +
> config PWM_SUNPLUS
> tristate "Sunplus PWM support"
> depends on ARCH_SUNPLUS || COMPILE_TEST
> diff --git a/drivers/pwm/Makefile b/drivers/pwm/Makefile
> index c5ec9e168ee7..dcad0d5a2430 100644
> --- a/drivers/pwm/Makefile
> +++ b/drivers/pwm/Makefile
> @@ -58,6 +58,7 @@ obj-$(CONFIG_PWM_STM32) += pwm-stm32.o
> obj-$(CONFIG_PWM_STM32_LP) += pwm-stm32-lp.o
> obj-$(CONFIG_PWM_STMPE) += pwm-stmpe.o
> obj-$(CONFIG_PWM_SUN4I) += pwm-sun4i.o
> +obj-$(CONFIG_PWM_SUN20I) += pwm-sun20i.o
> obj-$(CONFIG_PWM_SUNPLUS) += pwm-sunplus.o
> obj-$(CONFIG_PWM_TEGRA) += pwm-tegra.o
> obj-$(CONFIG_PWM_TIECAP) += pwm-tiecap.o
> diff --git a/drivers/pwm/pwm-sun20i.c b/drivers/pwm/pwm-sun20i.c
> new file mode 100644
> index 000000000000..3e3b5b138b30
> --- /dev/null
> +++ b/drivers/pwm/pwm-sun20i.c
> @@ -0,0 +1,387 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * PWM Controller Driver for sunxi platforms (D1, T113-S3 and R329)
> + *
> + * Limitations:
> + * - When the parameters change, current running period will not be completed
> + * and run new settings immediately.
> + * - It output HIGH-Z state when PWM channel disabled.
> + *
> + * Copyright (c) 2023 Aleksandr Shubin <privatesub2 at gmail.com>
> + */
> +
> +#include <linux/bitfield.h>
> +#include <linux/clk.h>
> +#include <linux/err.h>
> +#include <linux/io.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/platform_device.h>
> +#include <linux/pwm.h>
> +#include <linux/reset.h>
> +
> +#define SUN20I_PWM_CLK_CFG(chan) (0x20 + (((chan) >> 1) * 0x4))
> +#define SUN20I_PWM_CLK_CFG_SRC GENMASK(8, 7)
> +#define SUN20I_PWM_CLK_CFG_DIV_M GENMASK(3, 0)
> +#define SUN20I_PWM_CLK_DIV_M_MAX 8
> +
> +#define SUN20I_PWM_CLK_GATE 0x40
> +#define SUN20I_PWM_CLK_GATE_BYPASS(chan) BIT((chan) + 16)
> +#define SUN20I_PWM_CLK_GATE_GATING(chan) BIT(chan)
> +
> +#define SUN20I_PWM_ENABLE 0x80
> +#define SUN20I_PWM_ENABLE_EN(chan) BIT(chan)
> +
> +#define SUN20I_PWM_CTL(chan) (0x100 + (chan) * 0x20)
> +#define SUN20I_PWM_CTL_ACT_STA BIT(8)
> +#define SUN20I_PWM_CTL_PRESCAL_K GENMASK(7, 0)
> +#define SUN20I_PWM_CTL_PRESCAL_K_MAX field_max(SUN20I_PWM_CTL_PRESCAL_K)
> +
> +#define SUN20I_PWM_PERIOD(chan) (0x104 + (chan) * 0x20)
> +#define SUN20I_PWM_PERIOD_ENTIRE_CYCLE GENMASK(31, 16)
> +#define SUN20I_PWM_PERIOD_ACT_CYCLE GENMASK(15, 0)
> +
> +#define SUN20I_PWM_PCNTR_SIZE BIT(16)
> +
> +/*
> + * SUN20I_PWM_MAGIC is used to quickly compute the values of the clock dividers
> + * div_m (SUN20I_PWM_CLK_CFG_DIV_M) & prescale_k (SUN20I_PWM_CTL_PRESCAL_K)
> + * without using a loop. These dividers limit the # of cycles in a period
> + * to SUN20I_PWM_PCNTR_SIZE by applying a scaling factor of
> + * 1/(div_m * (prescale_k + 1)) to the clock source.
> + *
> + * SUN20I_PWM_MAGIC is derived by solving for div_m and prescale_k
> + * such that for a given requested period,
> + *
> + * i) div_m is minimized for any prescale_k ≤ SUN20I_PWM_CTL_PRESCAL_K_MAX,
> + * ii) prescale_k is minimized.
> + *
> + * The derivation proceeds as follows, with val = # of cycles for requested
> + * period:
> + *
> + * for a given value of div_m we want the smallest prescale_k such that
> + *
> + * (val >> div_m) // (prescale_k + 1) ≤ 65536 (SUN20I_PWM_PCNTR_SIZE)
> + *
> + * This is equivalent to:
> + *
> + * (val >> div_m) ≤ 65536 * (prescale_k + 1) + prescale_k
> + * ⟺ (val >> div_m) ≤ 65537 * prescale_k + 65536
> + * ⟺ (val >> div_m) - 65536 ≤ 65537 * prescale_k
> + * ⟺ ((val >> div_m) - 65536) / 65537 ≤ prescale_k
> + *
> + * As prescale_k is integer, this becomes
> + *
> + * ((val >> div_m) - 65536) // 65537 ≤ prescale_k
> + *
> + * And is minimized at
> + *
> + * ((val >> div_m) - 65536) // 65537
> + *
> + * Now we pick the smallest div_m that satifies prescale_k ≤ 255
> + * (i.e SUN20I_PWM_CTL_PRESCAL_K_MAX),
> + *
> + * ((val >> div_m) - 65536) // 65537 ≤ 255
> + * ⟺ (val >> div_m) - 65536 ≤ 255 * 65537 + 65536
> + * ⟺ val >> div_m ≤ 255 * 65537 + 2 * 65536
> + * ⟺ val >> div_m < (255 * 65537 + 2 * 65536 + 1)
> + * ⟺ div_m = fls((val) / (255 * 65537 + 2 * 65536 + 1))
> + *
> + * Suggested by Uwe Kleine-König
This is really sophisticated, that guy seems to be a genius :-)
Ok, honestly: I didn't try to reunderstand this in this round. Will do
that for the next iteration again.
> + */
> +#define SUN20I_PWM_MAGIC (255 * 65537 + 2 * 65536 + 1)
> +
> +struct sun20i_pwm_chip {
> + struct clk *clk_bus, *clk_hosc, *clk_apb;
> + struct reset_control *rst;
> + struct pwm_chip chip;
> + void __iomem *base;
> + /* Mutex to protect pwm apply state */
> + struct mutex mutex;
> +};
Having a pwm_chip embedded in your driver private data doesn't work any
more since v6.10-rc1~168^2~31. See e.g. commit 792bc12573a3 ("pwm:
spear: Make use of devm_pwmchip_alloc() function") for an easy
conversion to what needs to be done today.
> [...]
> +static int sun20i_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
> + const struct pwm_state *state)
> +{
> + struct sun20i_pwm_chip *sun20i_chip = to_sun20i_pwm_chip(chip);
> + u64 bus_rate, hosc_rate, val, ent_cycle, act_cycle;
> + u32 clk_gate, clk_cfg, pwm_en, ctl, reg_period;
> + u32 prescale_k, div_m;
> + bool use_bus_clk;
> + int ret = 0;
> +
> + mutex_lock(&sun20i_chip->mutex);
> +
> + pwm_en = sun20i_pwm_readl(sun20i_chip, SUN20I_PWM_ENABLE);
> +
> + if (state->enabled != pwm->state.enabled) {
> + clk_gate = sun20i_pwm_readl(sun20i_chip, SUN20I_PWM_CLK_GATE);
> +
> + if (!state->enabled) {
> + clk_gate &= ~SUN20I_PWM_CLK_GATE_GATING(pwm->hwpwm);
> + pwm_en &= ~SUN20I_PWM_ENABLE_EN(pwm->hwpwm);
> + sun20i_pwm_writel(sun20i_chip, pwm_en, SUN20I_PWM_ENABLE);
> + sun20i_pwm_writel(sun20i_chip, clk_gate, SUN20I_PWM_CLK_GATE);
return 0 here?
> + }
> + }
> +
> + if (state->polarity != pwm->state.polarity ||
> + state->duty_cycle != pwm->state.duty_cycle ||
> + state->period != pwm->state.period) {
I guess this is true often enough that checking for it isn't worth the
effort. Also note that with the early return suggested above, the check
becomes bogous.
> + ctl = sun20i_pwm_readl(sun20i_chip, SUN20I_PWM_CTL(pwm->hwpwm));
> + clk_cfg = sun20i_pwm_readl(sun20i_chip, SUN20I_PWM_CLK_CFG(pwm->hwpwm));
> + hosc_rate = clk_get_rate(sun20i_chip->clk_hosc);
> + bus_rate = clk_get_rate(sun20i_chip->clk_apb);
> + if (pwm_en & SUN20I_PWM_ENABLE_EN(pwm->hwpwm ^ 1)) {
> + /* if the neighbor channel is enable, check period only */
s/enable/enabled/, maybe also mention that each SUN20I_PWM_CLK_CFG is
shared by two channels. I find it irritating that SUN20I_PWM_CLK_CFG(0)
== SUN20I_PWM_CLK_CFG(1). I suggest to drop the shift from the defintion
and use SUN20I_PWM_CLK_CFG(pwm->hwpwm / 2) to make this more visible in
the source code.
> + use_bus_clk = FIELD_GET(SUN20I_PWM_CLK_CFG_SRC, clk_cfg) != 0;
> + val = mul_u64_u64_div_u64(state->period,
> + (use_bus_clk ? bus_rate : hosc_rate),
> + NSEC_PER_SEC);
> +
> + div_m = FIELD_GET(SUN20I_PWM_CLK_CFG_DIV_M, clk_cfg);
> + } else {
> + /* check period and select clock source */
You're implicitly assuming here that bus_rate > hosc_rate. Maybe make
this explicit in a comment (and check for that in .probe()?)
> + use_bus_clk = false;
> + val = mul_u64_u64_div_u64(state->period, hosc_rate, NSEC_PER_SEC);
> + if (val <= 1) {
> + use_bus_clk = true;
> + val = mul_u64_u64_div_u64(state->period, bus_rate, NSEC_PER_SEC);
> + if (val <= 1) {
> + ret = -EINVAL;
> + goto unlock_mutex;
If you use a guard to lock the mutex, these gotos can just be replaced
by a return statement.
> + }
> + }
> + div_m = fls(DIV_ROUND_DOWN_ULL(val, SUN20I_PWM_MAGIC));
> + if (div_m > SUN20I_PWM_CLK_DIV_M_MAX) {
> + ret = -EINVAL;
> + goto unlock_mutex;
> + }
> +
> + /* set up the CLK_DIV_M and clock CLK_SRC */
> + clk_cfg = FIELD_PREP(SUN20I_PWM_CLK_CFG_DIV_M, div_m);
> + clk_cfg |= FIELD_PREP(SUN20I_PWM_CLK_CFG_SRC, use_bus_clk);
> +
> + sun20i_pwm_writel(sun20i_chip, clk_cfg, SUN20I_PWM_CLK_CFG(pwm->hwpwm));
> + }
> +
> + /* calculate prescale_k, PWM entire cycle */
> + ent_cycle = val >> div_m;
> + prescale_k = DIV_ROUND_DOWN_ULL(ent_cycle, 65537);
> + if (prescale_k > SUN20I_PWM_CTL_PRESCAL_K_MAX)
> + prescale_k = SUN20I_PWM_CTL_PRESCAL_K_MAX;
> +
> + do_div(ent_cycle, prescale_k + 1);
> +
> + /* for N cycles, PPRx.PWM_ENTIRE_CYCLE = (N-1) */
> + reg_period = FIELD_PREP(SUN20I_PWM_PERIOD_ENTIRE_CYCLE, ent_cycle - 1);
> +
> + /* set duty cycle */
> + val = mul_u64_u64_div_u64(state->duty_cycle,
> + (use_bus_clk ? bus_rate : hosc_rate),
> + NSEC_PER_SEC);
> + act_cycle = val >> div_m;
> + do_div(act_cycle, prescale_k + 1);
> +
> + /*
> + * The formula of the output period and the duty-cycle for PWM are as follows.
> + * T period = (PWM01_CLK / PWM0_PRESCALE_K)^-1 * (PPR0.PWM_ENTIRE_CYCLE + 1)
(PWM01_CLK / PWM0_PRESCALE_K)^-1 = PWM0_PRESCALE_K / PWM01_CLK
> + * T high-level = (PWM01_CLK / PWM0_PRESCALE_K)^-1 * PPR0.PWM_ACT_CYCLE
> + * Duty-cycle = T high-level / T period
> + */
> + reg_period |= FIELD_PREP(SUN20I_PWM_PERIOD_ACT_CYCLE, act_cycle);
> + sun20i_pwm_writel(sun20i_chip, reg_period, SUN20I_PWM_PERIOD(pwm->hwpwm));
> +
> + ctl = FIELD_PREP(SUN20I_PWM_CTL_PRESCAL_K, prescale_k);
> + if (state->polarity == PWM_POLARITY_NORMAL)
> + ctl |= SUN20I_PWM_CTL_ACT_STA;
> +
> + sun20i_pwm_writel(sun20i_chip, ctl, SUN20I_PWM_CTL(pwm->hwpwm));
> + }
> +
> + if (state->enabled != pwm->state.enabled && state->enabled) {
> + clk_gate &= ~SUN20I_PWM_CLK_GATE_BYPASS(pwm->hwpwm);
> + clk_gate |= SUN20I_PWM_CLK_GATE_GATING(pwm->hwpwm);
> + pwm_en |= SUN20I_PWM_ENABLE_EN(pwm->hwpwm);
> + sun20i_pwm_writel(sun20i_chip, pwm_en, SUN20I_PWM_ENABLE);
> + sun20i_pwm_writel(sun20i_chip, clk_gate, SUN20I_PWM_CLK_GATE);
> + }
> +
> +unlock_mutex:
> + mutex_unlock(&sun20i_chip->mutex);
> +
> + return ret;
> +}
> +
> +static const struct pwm_ops sun20i_pwm_ops = {
> + .apply = sun20i_pwm_apply,
> + .get_state = sun20i_pwm_get_state,
> +};
> +
> +static const struct of_device_id sun20i_pwm_dt_ids[] = {
> + { .compatible = "allwinner,sun20i-d1-pwm" },
> + { },
> +};
> +MODULE_DEVICE_TABLE(of, sun20i_pwm_dt_ids);
> +
> +static void sun20i_pwm_reset_ctrl_release(void *data)
> +{
> + struct reset_control *rst = data;
> +
> + reset_control_assert(rst);
> +}
> +
> +static int sun20i_pwm_probe(struct platform_device *pdev)
> +{
> + struct sun20i_pwm_chip *sun20i_chip;
> + int ret;
> +
> + sun20i_chip = devm_kzalloc(&pdev->dev, sizeof(*sun20i_chip), GFP_KERNEL);
> + if (!sun20i_chip)
> + return -ENOMEM;
> +
> + sun20i_chip->base = devm_platform_ioremap_resource(pdev, 0);
> + if (IS_ERR(sun20i_chip->base))
> + return PTR_ERR(sun20i_chip->base);
> +
> + sun20i_chip->clk_bus = devm_clk_get_enabled(&pdev->dev, "bus");
> + if (IS_ERR(sun20i_chip->clk_bus))
> + return dev_err_probe(&pdev->dev, PTR_ERR(sun20i_chip->clk_bus),
> + "failed to get bus clock\n");
> +
> + sun20i_chip->clk_hosc = devm_clk_get_enabled(&pdev->dev, "hosc");
> + if (IS_ERR(sun20i_chip->clk_hosc))
> + return dev_err_probe(&pdev->dev, PTR_ERR(sun20i_chip->clk_hosc),
> + "failed to get hosc clock\n");
> +
> + sun20i_chip->clk_apb = devm_clk_get_enabled(&pdev->dev, "apb");
> + if (IS_ERR(sun20i_chip->clk_apb))
> + return dev_err_probe(&pdev->dev, PTR_ERR(sun20i_chip->clk_apb),
> + "failed to get apb clock\n");
> +
> + sun20i_chip->rst = devm_reset_control_get_exclusive(&pdev->dev, NULL);
> + if (IS_ERR(sun20i_chip->rst))
> + return dev_err_probe(&pdev->dev, PTR_ERR(sun20i_chip->rst),
> + "failed to get bus reset\n");
> +
> + ret = of_property_read_u32(pdev->dev.of_node, "allwinner,pwm-channels",
> + &sun20i_chip->chip.npwm);
> + if (ret)
> + sun20i_chip->chip.npwm = 8;
> +
> + if (sun20i_chip->chip.npwm > 16) {
> + dev_info(&pdev->dev, "Limiting number of PWM lines from %u to 16",
> + sun20i_chip->chip.npwm);
> + sun20i_chip->chip.npwm = 16;
> + }
> +
> + /* Deassert reset */
> + ret = reset_control_deassert(sun20i_chip->rst);
> + if (ret)
> + return dev_err_probe(&pdev->dev, ret, "failed to deassert reset\n");
> +
> + ret = devm_add_action_or_reset(&pdev->dev, sun20i_pwm_reset_ctrl_release, sun20i_chip->rst);
> + if (ret)
> + return ret;
At some point in the future this can be simplified using
devm_reset_control_get_exclusive_deasserted(). See
https://lore.kernel.org/linux-arm-kernel/20240621-reset-get-deasserted-v1-2-94ee76fb7b7d@pengutronix.de
> + sun20i_chip->chip.dev = &pdev->dev;
> + sun20i_chip->chip.ops = &sun20i_pwm_ops;
> +
> + mutex_init(&sun20i_chip->mutex);
> +
> + ret = devm_pwmchip_add(&pdev->dev, &sun20i_chip->chip);
> + if (ret < 0)
> + return dev_err_probe(&pdev->dev, ret, "failed to add PWM chip\n");
> +
> + platform_set_drvdata(pdev, sun20i_chip);
This is unused.
> + return 0;
> +}
> +
> +static struct platform_driver sun20i_pwm_driver = {
> + .driver = {
> + .name = "sun20i-pwm",
> + .of_match_table = sun20i_pwm_dt_ids,
> + },
> + .probe = sun20i_pwm_probe,
> +};
> +module_platform_driver(sun20i_pwm_driver);
> +
> +MODULE_AUTHOR("Aleksandr Shubin <privatesub2 at gmail.com>");
> +MODULE_DESCRIPTION("Allwinner sun20i PWM driver");
> +MODULE_LICENSE("GPL");
Best regards
Uwe
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 488 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20240708/35337823/attachment.sig>
More information about the linux-arm-kernel
mailing list