[PATCH v2 1/5] arm64: dts: ti: k3-j721s2*: Add bootph-* properties
Manorit Chawdhry
m-chawdhry at ti.com
Thu Jul 4 23:26:27 PDT 2024
Adds bootph-* properties to the leaf nodes to enable U-boot to
utilise them.
Signed-off-by: Manorit Chawdhry <m-chawdhry at ti.com>
---
arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts | 14 ++++++++++++++
arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 2 ++
arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi | 12 ++++++++++++
arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 2 ++
4 files changed, 30 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
index c5a0b7cbb14f..6ce14f9e087b 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
@@ -138,6 +138,7 @@ J721S2_IOPAD(0x044, PIN_OUTPUT, 14) /* (Y26) MCASP0_AXR1.UART8_RTSn */
J721S2_IOPAD(0x0d0, PIN_INPUT, 11) /* (AF26) SPI0_CS1.UART8_RXD */
J721S2_IOPAD(0x0d4, PIN_OUTPUT, 11) /* (AH27) SPI0_CLK.UART8_TXD */
>;
+ bootph-all;
};
main_i2c3_pins_default: main-i2c3-default-pins {
@@ -165,6 +166,7 @@ J721S2_IOPAD(0x0f4, PIN_INPUT, 0) /* (R24) MMC1_DAT2 */
J721S2_IOPAD(0x0f0, PIN_INPUT, 0) /* (R22) MMC1_DAT3 */
J721S2_IOPAD(0x0e8, PIN_INPUT, 8) /* (AE25) TIMER_IO0.MMC1_SDCD */
>;
+ bootph-all;
};
vdd_sd_dv_pins_default: vdd-sd-dv-default-pins {
@@ -177,6 +179,7 @@ main_usbss0_pins_default: main-usbss0-default-pins {
pinctrl-single,pins = <
J721S2_IOPAD(0x0ec, PIN_OUTPUT, 6) /* (AG25) TIMER_IO1.USB0_DRVVBUS */
>;
+ bootph-all;
};
main_mcan3_pins_default: main-mcan3-default-pins {
@@ -200,6 +203,7 @@ wkup_uart0_pins_default: wkup-uart0-default-pins {
J721S2_WKUP_IOPAD(0x048, PIN_INPUT, 0) /* (D28) WKUP_UART0_RXD */
J721S2_WKUP_IOPAD(0x04c, PIN_OUTPUT, 0) /* (D27) WKUP_UART0_TXD */
>;
+ bootph-all;
};
mcu_uart0_pins_default: mcu-uart0-default-pins {
@@ -209,6 +213,7 @@ J721S2_WKUP_IOPAD(0x094, PIN_OUTPUT, 0) /* (D25) WKUP_GPIO0_15.MCU_UART0_RTSn */
J721S2_WKUP_IOPAD(0x08c, PIN_INPUT, 0) /* (C24) WKUP_GPIO0_13.MCU_UART0_RXD */
J721S2_WKUP_IOPAD(0x088, PIN_OUTPUT, 0) /* (C25) WKUP_GPIO0_12.MCU_UART0_TXD */
>;
+ bootph-all;
};
mcu_cpsw_pins_default: mcu-cpsw-default-pins {
@@ -301,6 +306,7 @@ J721S2_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (A20) MCU_OSPI1_D3 */
J721S2_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (B19) MCU_OSPI1_DQS */
J721S2_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (B20) MCU_OSPI1_LBCLKO */
>;
+ bootph-all;
};
};
@@ -316,12 +322,14 @@ &wkup_uart0 {
status = "reserved";
pinctrl-names = "default";
pinctrl-0 = <&wkup_uart0_pins_default>;
+ bootph-all;
};
&mcu_uart0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mcu_uart0_pins_default>;
+ bootph-all;
};
&main_uart8 {
@@ -330,6 +338,7 @@ &main_uart8 {
pinctrl-0 = <&main_uart8_pins_default>;
/* Shared with TFA on this platform */
power-domains = <&k3_pds 357 TI_SCI_PD_SHARED>;
+ bootph-all;
};
&main_i2c0 {
@@ -385,6 +394,7 @@ &main_sdhci0 {
non-removable;
ti,driver-strength-ohm = <50>;
disable-wp;
+ bootph-all;
};
&main_sdhci1 {
@@ -395,6 +405,7 @@ &main_sdhci1 {
disable-wp;
vmmc-supply = <&vdd_mmc1>;
vqmmc-supply = <&vdd_sd_dv>;
+ bootph-all;
};
&mcu_cpsw {
@@ -446,11 +457,13 @@ &usbss0 {
pinctrl-names = "default";
ti,vbus-divider;
ti,usb2-only;
+ bootph-all;
};
&usb0 {
dr_mode = "otg";
maximum-speed = "high-speed";
+ bootph-all;
};
&ospi1 {
@@ -469,6 +482,7 @@ flash at 0 {
cdns,tchsh-ns = <60>;
cdns,tslch-ns = <60>;
cdns,read-delay = <2>;
+ bootph-all;
};
};
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
index 9ed6949b40e9..0ea6817de65c 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
@@ -816,6 +816,7 @@ secure_proxy_main: mailbox at 32c00000 {
<0x00 0x32800000 0x00 0x100000>;
interrupt-names = "rx_011";
interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ bootph-all;
};
hwspinlock: spinlock at 30e00000 {
@@ -1225,6 +1226,7 @@ usb0: usb at 6000000 {
interrupt-names = "host", "peripheral", "otg";
maximum-speed = "super-speed";
dr_mode = "otg";
+ bootph-all;
};
};
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
index 8feb42c89e47..497e0dfa8011 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
@@ -17,20 +17,24 @@ sms: system-controller at 44083000 {
reg-names = "debug_messages";
reg = <0x00 0x44083000 0x00 0x1000>;
+ bootph-all;
k3_pds: power-controller {
compatible = "ti,sci-pm-domain";
#power-domain-cells = <2>;
+ bootph-all;
};
k3_clks: clock-controller {
compatible = "ti,k2g-sci-clk";
#clock-cells = <2>;
+ bootph-all;
};
k3_reset: reset-controller {
compatible = "ti,sci-reset";
#reset-cells = <2>;
+ bootph-all;
};
};
@@ -43,6 +47,7 @@ wkup_conf: bus at 43000000 {
chipid: chipid at 14 {
compatible = "ti,am654-chipid";
reg = <0x14 0x4>;
+ bootph-all;
};
};
@@ -59,6 +64,7 @@ secure_proxy_sa3: mailbox at 43600000 {
* firmware on non-MPU processors
*/
status = "disabled";
+ bootph-pre-ram;
};
mcu_ram: sram at 41c00000 {
@@ -170,6 +176,7 @@ mcu_timer0: timer at 40400000 {
ti,timer-pwm;
/* Non-MPU Firmware usage */
status = "reserved";
+ bootph-pre-ram;
};
mcu_timer1: timer at 40410000 {
@@ -362,6 +369,7 @@ wkup_i2c0: i2c at 42120000 {
clock-names = "fck";
power-domains = <&k3_pds 223 TI_SCI_PD_EXCLUSIVE>;
status = "disabled";
+ bootph-all;
};
mcu_i2c0: i2c at 40b00000 {
@@ -474,6 +482,7 @@ mcu_ringacc: ringacc at 2b800000 {
ti,sci = <&sms>;
ti,sci-dev-id = <272>;
msi-parent = <&main_udmass_inta>;
+ bootph-all;
};
mcu_udmap: dma-controller at 285c0000 {
@@ -497,6 +506,7 @@ mcu_udmap: dma-controller at 285c0000 {
ti,sci-rm-range-rchan = <0x0a>, /* RX_CHAN */
<0x0b>; /* RX_HCHAN */
ti,sci-rm-range-rflow = <0x00>; /* GP RFLOW */
+ bootph-all;
};
};
@@ -513,6 +523,7 @@ secure_proxy_mcu: mailbox at 2a480000 {
* firmware on non-MPU processors
*/
status = "disabled";
+ bootph-pre-ram;
};
mcu_cpsw: ethernet at 46000000 {
@@ -667,6 +678,7 @@ wkup_vtm0: temperature-sensor at 42040000 {
<0x00 0x42050000 0x0 0x350>;
power-domains = <&k3_pds 180 TI_SCI_PD_SHARED>;
#thermal-sensor-cells = <1>;
+ bootph-pre-ram;
};
mcu_r5fss0: r5fss at 41000000 {
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
index 82aacc01e8fe..dfcc223809e7 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
@@ -170,6 +170,7 @@ J721S2_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (F20) MCU_OSPI0_D7 */
J721S2_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (E18) MCU_OSPI0_DQS */
J721S2_WKUP_IOPAD(0x004, PIN_INPUT, 0) /* (E20) MCU_OSPI0_LBCLKO */
>;
+ bootph-all;
};
};
@@ -445,6 +446,7 @@ flash at 0 {
cdns,tchsh-ns = <60>;
cdns,tslch-ns = <60>;
cdns,read-delay = <4>;
+ bootph-all;
};
};
--
2.45.1
More information about the linux-arm-kernel
mailing list