[PATCH 2/2] arm64: dts: imx93-phycore-segin: Add Phytec i.MX93 Segin

Wadim Egorov w.egorov at phytec.de
Tue Jan 16 23:00:15 PST 2024


Hi,

would be nice if you could include the author to CC.

CC'ing Christoph.

Regards,
Wadim

Am 16.01.24 um 12:39 schrieb Mathieu Othacehe:
> Add DTSI for Phytec i.MX93 System on Module and DTS for Phytec
> i.MX93 on Segin evaluation board.
>
> This version comes with:
>   - 1GB LPDDR4 RAM
>   - external SD
>   - debug UART
>   - 1x 100Mbit Ethernet
>
> Signed-off-by: Mathieu Othacehe <othacehe at gnu.org>
> ---
>   arch/arm64/boot/dts/freescale/Makefile        |  1 +
>   .../dts/freescale/imx93-phycore-segin.dts     | 93 +++++++++++++++++++
>   .../boot/dts/freescale/imx93-phycore-som.dtsi | 51 ++++++++++
>   3 files changed, 145 insertions(+)
>   create mode 100644 arch/arm64/boot/dts/freescale/imx93-phycore-segin.dts
>   create mode 100644 arch/arm64/boot/dts/freescale/imx93-phycore-som.dtsi
>
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index 2e027675d7bb..6cb6d9f8783e 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -203,6 +203,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8ulp-evk.dtb
>   dtb-$(CONFIG_ARCH_MXC) += imx93-11x11-evk.dtb
>   dtb-$(CONFIG_ARCH_MXC) += imx93-tqma9352-mba93xxca.dtb
>   dtb-$(CONFIG_ARCH_MXC) += imx93-tqma9352-mba93xxla.dtb
> +dtb-$(CONFIG_ARCH_MXC) += imx93-phycore-segin.dtb
>   
>   imx8mm-venice-gw72xx-0x-imx219-dtbs	:= imx8mm-venice-gw72xx-0x.dtb imx8mm-venice-gw72xx-0x-imx219.dtbo
>   imx8mm-venice-gw72xx-0x-rpidsi-dtbs	:= imx8mm-venice-gw72xx-0x.dtb imx8mm-venice-gw72xx-0x-rpidsi.dtbo
> diff --git a/arch/arm64/boot/dts/freescale/imx93-phycore-segin.dts b/arch/arm64/boot/dts/freescale/imx93-phycore-segin.dts
> new file mode 100644
> index 000000000000..2277d97fc3c4
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx93-phycore-segin.dts
> @@ -0,0 +1,93 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (C) 2023 PHYTEC Messtechnik GmbH
> + * Christoph Stoidner <c.stoidner at phytec.de>
> + * Copyright (C) 2024 Mathieu Othacehe <m.othacehe at gmail.com>
> + *
> + */
> +/dts-v1/;
> +
> +#include "imx93-phycore-som.dtsi"
> +
> +/{
> +	model = "PHYTEC phyBOARD-Segin-i.MX93";
> +	compatible = "phytec,imx93-phycore-segin",
> +		     "phytec,imx93-phycore-som", "fsl,imx93";
> +
> +	chosen {
> +		stdout-path = &lpuart1;
> +	};
> +
> +	reg_usdhc2_vmmc: regulator-usdhc2 {
> +		compatible = "regulator-fixed";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
> +		regulator-name = "VSD_3V3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpio = <&gpio3 7 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
> +};
> +
> +/* Console */
> +&lpuart1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart1>;
> +	status = "okay";
> +};
> +
> +/* SD-Card */
> +&usdhc2 {
> +	pinctrl-names = "default", "state_100mhz", "state_200mhz";
> +	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
> +	pinctrl-1 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
> +	pinctrl-2 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
> +	cd-gpios = <&gpio3 00 GPIO_ACTIVE_LOW>;
> +	vmmc-supply = <&reg_usdhc2_vmmc>;
> +	bus-width = <4>;
> +	status = "okay";
> +	no-sdio;
> +	no-mmc;
> +};
> +
> +/* Watchdog */
> +&wdog3 {
> +	status = "okay";
> +};
> +
> +&iomuxc {
> +	pinctrl-names = "default";
> +	status = "okay";
> +
> +	pinctrl_uart1: uart1grp {
> +		fsl,pins = <
> +			MX93_PAD_UART1_RXD__LPUART1_RX			0x31e
> +			MX93_PAD_UART1_TXD__LPUART1_TX			0x31e
> +		>;
> +	};
> +
> +	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
> +		fsl,pins = <
> +			MX93_PAD_SD2_RESET_B__GPIO3_IO07		0x31e
> +		>;
> +	};
> +
> +	pinctrl_usdhc2_gpio: usdhc2gpiogrp {
> +		fsl,pins = <
> +			MX93_PAD_SD2_CD_B__GPIO3_IO00			0x31e
> +		>;
> +	};
> +
> +	pinctrl_usdhc2: usdhc2grp {
> +		fsl,pins = <
> +			MX93_PAD_SD2_CLK__USDHC2_CLK			0x178e
> +			MX93_PAD_SD2_CMD__USDHC2_CMD			0x139e
> +			MX93_PAD_SD2_DATA0__USDHC2_DATA0		0x138e
> +			MX93_PAD_SD2_DATA1__USDHC2_DATA1		0x138e
> +			MX93_PAD_SD2_DATA2__USDHC2_DATA2		0x138e
> +			MX93_PAD_SD2_DATA3__USDHC2_DATA3		0x139e
> +			MX93_PAD_SD2_VSELECT__USDHC2_VSELECT		0x51e
> +		>;
> +	};
> +};
> diff --git a/arch/arm64/boot/dts/freescale/imx93-phycore-som.dtsi b/arch/arm64/boot/dts/freescale/imx93-phycore-som.dtsi
> new file mode 100644
> index 000000000000..7a9ff998a342
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx93-phycore-som.dtsi
> @@ -0,0 +1,51 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (C) 2023 PHYTEC Messtechnik GmbH
> + * Christoph Stoidner <c.stoidner at phytec.de>
> + * Copyright (C) 2024 Mathieu Othacehe <m.othacehe at gmail.com>
> + *
> + */
> +/dts-v1/;
> +
> +#include "imx93.dtsi"
> +
> +/{
> +	model = "PHYTEC phyCORE-i.MX93";
> +	compatible = "phytec,imx93-phycore-som", "fsl,imx93";
> +
> +	reserved-memory {
> +		ranges;
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +	};
> +};
> +
> +/* eMMC */
> +&usdhc1 {
> +	pinctrl-names = "default", "state_100mhz", "state_200mhz";
> +	pinctrl-0 = <&pinctrl_usdhc1>;
> +	pinctrl-1 = <&pinctrl_usdhc1>;
> +	pinctrl-2 = <&pinctrl_usdhc1>;
> +	bus-width = <8>;
> +	non-removable;
> +	status = "okay";
> +};
> +
> +&iomuxc {
> +	pinctrl_usdhc1: usdhc1grp {
> +		fsl,pins = <
> +			MX93_PAD_SD1_CLK__USDHC1_CLK		0x15fe
> +			MX93_PAD_SD1_CMD__USDHC1_CMD		0x13fe
> +			MX93_PAD_SD1_DATA0__USDHC1_DATA0	0x13fe
> +			MX93_PAD_SD1_DATA1__USDHC1_DATA1	0x13fe
> +			MX93_PAD_SD1_DATA2__USDHC1_DATA2	0x13fe
> +			MX93_PAD_SD1_DATA3__USDHC1_DATA3	0x13fe
> +			MX93_PAD_SD1_DATA4__USDHC1_DATA4	0x13fe
> +			MX93_PAD_SD1_DATA5__USDHC1_DATA5	0x13fe
> +			MX93_PAD_SD1_DATA6__USDHC1_DATA6	0x13fe
> +			MX93_PAD_SD1_DATA7__USDHC1_DATA7	0x13fe
> +			MX93_PAD_SD1_STROBE__USDHC1_STROBE	0x15fe
> +		>;
> +	};
> +
> +};



More information about the linux-arm-kernel mailing list