[PATCH v2 6/7] arm64: Add initial support for Blaize BLZP1600 CB2
Conor Dooley
conor at kernel.org
Wed Apr 24 08:15:37 PDT 2024
On Wed, Apr 24, 2024 at 01:33:23PM +0000, Niko Pasaloukos wrote:
> Adds support for the Blaize CB2 development board based on
> BLZP1600 SoC. This consists of a Carrier-Board-2 and a SoM.
>
> The blaize-blzp1600.dtsi is the common part for the SoC,
> blaize-blzp1600-som.dtsi is the common part for the SoM and
> blaize-blzp1600-cb2.dts is the board specific file.
>
> 'make dtbs_check' complains about ['ti,ina3221'] and ['national,lm96163']
> which are already upstreamed drivers with no yaml documentation.
Might not be what you want to hear, but please add yaml documentation
for them. Rob told you to do so on v1:
https://lore.kernel.org/all/20230412140344.GA2234522-robh@kernel.org/
That said, I went and looked. ina3221 _is_ documented in a yaml binding
and has been since October. national,lm96163 on the other hand, you'll
have to document if you want to use it.
Cheers,
Conor.
>
> Co-developed-by: James Cowgill <james.cowgill at blaize.com>
> Signed-off-by: James Cowgill <james.cowgill at blaize.com>
> Co-developed-by: Matt Redfearn <matt.redfearn at blaize.com>
> Signed-off-by: Matt Redfearn <matt.redfearn at blaize.com>
> Co-developed-by: Neil Jones <neil.jones at blaize.com>
> Signed-off-by: Neil Jones <neil.jones at blaize.com>
> Signed-off-by: Nikolaos Pasaloukos <nikolaos.pasaloukos at blaize.com>
> ---
> arch/arm64/boot/dts/Makefile | 1 +
> arch/arm64/boot/dts/blaize/Makefile | 2 +
> .../boot/dts/blaize/blaize-blzp1600-cb2.dts | 84 +++++++
> .../boot/dts/blaize/blaize-blzp1600-som.dtsi | 23 ++
> .../boot/dts/blaize/blaize-blzp1600.dtsi | 211 ++++++++++++++++++
> 5 files changed, 321 insertions(+)
> create mode 100644 arch/arm64/boot/dts/blaize/Makefile
> create mode 100644 arch/arm64/boot/dts/blaize/blaize-blzp1600-cb2.dts
> create mode 100644 arch/arm64/boot/dts/blaize/blaize-blzp1600-som.dtsi
> create mode 100644 arch/arm64/boot/dts/blaize/blaize-blzp1600.dtsi
>
> diff --git a/arch/arm64/boot/dts/Makefile b/arch/arm64/boot/dts/Makefile
> index 30dd6347a929..601b6381ea0c 100644
> --- a/arch/arm64/boot/dts/Makefile
> +++ b/arch/arm64/boot/dts/Makefile
> @@ -9,6 +9,7 @@ subdir-y += apm
> subdir-y += apple
> subdir-y += arm
> subdir-y += bitmain
> +subdir-y += blaize
> subdir-y += broadcom
> subdir-y += cavium
> subdir-y += exynos
> diff --git a/arch/arm64/boot/dts/blaize/Makefile b/arch/arm64/boot/dts/blaize/Makefile
> new file mode 100644
> index 000000000000..595e7a350300
> --- /dev/null
> +++ b/arch/arm64/boot/dts/blaize/Makefile
> @@ -0,0 +1,2 @@
> +# SPDX-License-Identifier: GPL-2.0
> +dtb-$(CONFIG_ARCH_BLAIZE_BLZP1600) += blaize-blzp1600-cb2.dtb
> diff --git a/arch/arm64/boot/dts/blaize/blaize-blzp1600-cb2.dts b/arch/arm64/boot/dts/blaize/blaize-blzp1600-cb2.dts
> new file mode 100644
> index 000000000000..0bdec7e81380
> --- /dev/null
> +++ b/arch/arm64/boot/dts/blaize/blaize-blzp1600-cb2.dts
> @@ -0,0 +1,84 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2023 Blaize, Inc. All rights reserved.
> + */
> +
> +/dts-v1/;
> +
> +#include "blaize-blzp1600-som.dtsi"
> +#include <dt-bindings/net/ti-dp83867.h>
> +
> +/ {
> + model = "Blaize BLZP1600 SoM1600P CB2 Development Board";
> +
> + compatible = "blaize,blzp1600-cb2", "blaize,blzp1600";
> +
> + aliases {
> + serial0 = &uart0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200";
> + };
> +};
> +
> +&i2c0 {
> + clock-frequency = <100000>;
> + status = "okay";
> +};
> +
> +&i2c1 {
> + clock-frequency = <100000>;
> + status = "okay";
> +};
> +
> +&i2c3 {
> + clock-frequency = <100000>;
> + status = "okay";
> +
> + gpio_expander: gpio at 74 {
> + compatible = "ti,tca9539";
> + reg = <0x74>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-line-names = "RSP_PIN_7", /* GPIO_0 */
> + "RSP_PIN_11", /* GPIO_1 */
> + "RSP_PIN_13", /* GPIO_2 */
> + "RSP_PIN_15", /* GPIO_3 */
> + "RSP_PIN_27", /* GPIO_4 */
> + "RSP_PIN_29", /* GPIO_5 */
> + "RSP_PIN_31", /* GPIO_6 */
> + "RSP_PIN_33", /* GPIO_7 */
> + "RSP_PIN_37", /* GPIO_8 */
> + "RSP_PIN_16", /* GPIO_9 */
> + "RSP_PIN_18", /* GPIO_10 */
> + "RSP_PIN_22", /* GPIO_11 */
> + "RSP_PIN_28", /* GPIO_12 */
> + "RSP_PIN_32", /* GPIO_13 */
> + "RSP_PIN_36", /* GPIO_14 */
> + "TP31"; /* GPIO_15 */
> + };
> +
> + gpio_expander_m2: gpio at 75 {
> + compatible = "ti,tca9539";
> + reg = <0x75>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-line-names = "M2_W_DIS1_N", /* GPIO_0 */
> + "M2_W_DIS2_N", /* GPIO_1 */
> + "M2_UART_WAKE_N", /* GPIO_2 */
> + "M2_COEX3", /* GPIO_3 */
> + "M2_COEX_RXD", /* GPIO_4 */
> + "M2_COEX_TXD", /* GPIO_5 */
> + "M2_VENDOR_PIN40", /* GPIO_6 */
> + "M2_VENDOR_PIN42", /* GPIO_7 */
> + "M2_VENDOR_PIN38", /* GPIO_8 */
> + "M2_SDIO_RST_N", /* GPIO_9 */
> + "M2_SDIO_WAKE_N", /* GPIO_10 */
> + "M2_PETN1", /* GPIO_11 */
> + "M2_PERP1", /* GPIO_12 */
> + "M2_PERN1", /* GPIO_13 */
> + "UIM_SWP", /* GPIO_14 */
> + "UART1_TO_RSP"; /* GPIO_15 */
> + };
> +};
> diff --git a/arch/arm64/boot/dts/blaize/blaize-blzp1600-som.dtsi b/arch/arm64/boot/dts/blaize/blaize-blzp1600-som.dtsi
> new file mode 100644
> index 000000000000..efac0d6b3d60
> --- /dev/null
> +++ b/arch/arm64/boot/dts/blaize/blaize-blzp1600-som.dtsi
> @@ -0,0 +1,23 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2023 Blaize, Inc. All rights reserved.
> + */
> +
> +#include "blaize-blzp1600.dtsi"
> +
> +/ {
> + memory at 1000 {
> + device_type = "memory";
> + reg = <0x0 0x00001000 0xfffff000>;
> + };
> +};
> +
> +/* i2c4 bus is available only on the SoM, not on the board */
> +&i2c4 {
> + clock-frequency = <100000>;
> + status = "okay";
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/blaize/blaize-blzp1600.dtsi b/arch/arm64/boot/dts/blaize/blaize-blzp1600.dtsi
> new file mode 100644
> index 000000000000..ad1e502559d8
> --- /dev/null
> +++ b/arch/arm64/boot/dts/blaize/blaize-blzp1600.dtsi
> @@ -0,0 +1,211 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2023 Blaize, Inc. All rights reserved.
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/reset/blaize,blzp1600-reset.h>
> +#include <dt-bindings/clock/blaize,blzp1600-clk.h>
> +
> +/ {
> + interrupt-parent = <&gic>;
> + #address-cells = <2>;
> + #size-cells = <1>;
> +
> + cpus {
> + #address-cells = <2>;
> + #size-cells = <0>;
> +
> + cpu0: cpu at 0 {
> + compatible = "arm,cortex-a53";
> + device_type = "cpu";
> + enable-method = "psci";
> + reg = <0x0 0x0>;
> + next-level-cache = <&l2>;
> + };
> +
> + cpu1: cpu at 1 {
> + compatible = "arm,cortex-a53";
> + device_type = "cpu";
> + enable-method = "psci";
> + reg = <0x0 0x1>;
> + next-level-cache = <&l2>;
> + };
> +
> + l2: l2-cache0 {
> + compatible = "cache";
> + cache-level = <2>;
> + cache-unified;
> + };
> + };
> +
> + timer {
> + compatible = "arm,armv8-timer";
> + interrupts = /* Physical Secure PPI */
> + <GIC_PPI 13 (GIC_CPU_MASK_RAW(0x3) |
> + IRQ_TYPE_LEVEL_LOW)>,
> + /* Physical Non-Secure PPI */
> + <GIC_PPI 14 (GIC_CPU_MASK_RAW(0x3) |
> + IRQ_TYPE_LEVEL_LOW)>,
> + /* Hypervisor PPI */
> + <GIC_PPI 10 (GIC_CPU_MASK_RAW(0x3) |
> + IRQ_TYPE_LEVEL_LOW)>,
> + /* Virtual PPI */
> + <GIC_PPI 11 (GIC_CPU_MASK_RAW(0x3) |
> + IRQ_TYPE_LEVEL_LOW)>;
> + };
> +
> + psci {
> + compatible = "arm,psci-1.0", "arm,psci-0.2";
> + method = "smc";
> + };
> +
> + pmu {
> + compatible = "arm,cortex-a53-pmu";
> + interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-affinity = <&cpu0>, <&cpu1>;
> + };
> +
> + sram at 0 {
> + /*
> + * On BLZP1600 there is no general purpose (non-secure) SRAM.
> + * A small DDR memory space has been reserved for general use.
> + */
> + compatible = "mmio-sram";
> + reg = <0x0 0x00000000 0x00001000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0 0x0 0x00000000 0x1000>;
> +
> + /* SCMI reserved buffer space on DDR space */
> + scmi0_shm: scmi-sram at 800 {
> + compatible = "arm,scmi-shmem";
> + reg = <0x800 0x80>;
> + };
> + };
> +
> + firmware {
> + scmi {
> + compatible = "arm,scmi-smc";
> + arm,smc-id = <0x82002000>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + shmem = <&scmi0_shm>;
> +
> + scmi_clk: protocol at 14 {
> + reg = <0x14>;
> + #clock-cells = <1>;
> + };
> +
> + scmi_rst: protocol at 16 {
> + reg = <0x16>;
> + #reset-cells = <1>;
> + };
> + };
> + };
> +
> + soc {
> + compatible = "simple-bus";
> + #address-cells = <2>;
> + #size-cells = <1>;
> + ranges;
> +
> + gic: interrupt-controller at 200410000 {
> + compatible = "arm,gic-400";
> + #interrupt-cells = <3>;
> + #address-cells = <0>;
> + interrupt-controller;
> + reg = <0x2 0x00410000 0x20000>,
> + <0x2 0x00420000 0x20000>,
> + <0x2 0x00440000 0x20000>,
> + <0x2 0x00460000 0x20000>;
> + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_RAW(0x3) |
> + IRQ_TYPE_LEVEL_LOW)>;
> + };
> +
> + uart0: serial at 2004d0000 {
> + compatible = "ns16550a";
> + reg = <0x2 0x004d0000 0x1000>;
> + clocks = <&scmi_clk BLZP1600_UART0_CLK>;
> + resets = <&scmi_rst BLZP1600_UART0_RST>;
> + reg-shift = <2>;
> + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
> + status = "disabled";
> + };
> +
> + uart1: serial at 2004e0000 {
> + compatible = "ns16550a";
> + reg = <0x2 0x004e0000 0x1000>;
> + clocks = <&scmi_clk BLZP1600_UART1_CLK>;
> + resets = <&scmi_rst BLZP1600_UART1_RST>;
> + reg-shift = <2>;
> + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
> + status = "disabled";
> + };
> +
> + i2c0: i2c at 2004f0000 {
> + compatible = "snps,designware-i2c";
> + reg = <0x2 0x004f0000 0x1000>;
> + interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk BLZP1600_I2C0_CLK>;
> + resets = <&scmi_rst BLZP1600_I2C0_RST>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c1: i2c at 200500000 {
> + compatible = "snps,designware-i2c";
> + reg = <0x2 0x00500000 0x1000>;
> + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk BLZP1600_I2C1_CLK>;
> + resets = <&scmi_rst BLZP1600_I2C1_RST>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c2: i2c at 200510000 {
> + compatible = "snps,designware-i2c";
> + reg = <0x2 0x00510000 0x1000>;
> + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk BLZP1600_I2C2_CLK>;
> + resets = <&scmi_rst BLZP1600_I2C2_RST>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c3: i2c at 200520000 {
> + compatible = "snps,designware-i2c";
> + reg = <0x2 0x00520000 0x1000>;
> + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk BLZP1600_I2C3_CLK>;
> + resets = <&scmi_rst BLZP1600_I2C3_RST>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c4: i2c at 200530000 {
> + compatible = "snps,designware-i2c";
> + reg = <0x2 0x00530000 0x1000>;
> + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk BLZP1600_I2C4_CLK>;
> + resets = <&scmi_rst BLZP1600_I2C4_RST>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + arm_cc712: crypto at 200550000 {
> + compatible = "arm,cryptocell-712-ree";
> + reg = <0x2 0x00550000 0x1000>;
> + interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk 7>;
> + };
> + };
> +};
> --
> 2.34.1
>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 228 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20240424/44d78f32/attachment-0001.sig>
More information about the linux-arm-kernel
mailing list