[PATCH v2 09/12] arm64: dts: imx93-11x11-evk: add different usdhc pinctrl for different timing usage

[Peng Fan (OSS)]

From: Luke Wang <ziniu.wang_1 at nxp.com>

imx93-11x11-evk dts use the strongest driver strength for
default(high-speed), 100MHz(SDR50/DDR50/DDR52) and
200MHz(SDR104/HS200/HS400) timing. To make usdhc working appropriately for
each timing, add X1 drive strength to default timing and X3 drive
strength to 100MHz timing.

Reviewed-by: Haibo Chen <haibo.chen at nxp.com>
Signed-off-by: Luke Wang <ziniu.wang_1 at nxp.com>
Signed-off-by: Peng Fan <peng.fan at nxp.com>
---
 arch/arm64/boot/dts/freescale/imx93-11x11-evk.dts | 68 +++++++++++++++++++++--
 1 file changed, 64 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx93-11x11-evk.dts b/arch/arm64/boot/dts/freescale/imx93-11x11-evk.dts
index 2b67724db685..f848cb0922ef 100644
--- a/arch/arm64/boot/dts/freescale/imx93-11x11-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx93-11x11-evk.dts
@@ -161,8 +161,8 @@ &lpuart5 {
 &usdhc1 {
 	pinctrl-names = "default", "state_100mhz", "state_200mhz";
 	pinctrl-0 = <&pinctrl_usdhc1>;
-	pinctrl-1 = <&pinctrl_usdhc1>;
-	pinctrl-2 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
 	bus-width = <8>;
 	non-removable;
 	status = "okay";
@@ -171,8 +171,8 @@ &usdhc1 {
 &usdhc2 {
 	pinctrl-names = "default", "state_100mhz", "state_200mhz";
 	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
-	pinctrl-1 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
-	pinctrl-2 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
 	cd-gpios = <&gpio3 00 GPIO_ACTIVE_LOW>;
 	vmmc-supply = <&reg_usdhc2_vmmc>;
 	bus-width = <4>;
@@ -391,6 +391,40 @@ MX93_PAD_CCM_CLKO2__GPIO3_IO27			0x31e
 
 	/* need to config the SION for data and cmd pad, refer to ERR052021 */
 	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX93_PAD_SD1_CLK__USDHC1_CLK		0x1582
+			MX93_PAD_SD1_CMD__USDHC1_CMD		0x40001382
+			MX93_PAD_SD1_DATA0__USDHC1_DATA0	0x40001382
+			MX93_PAD_SD1_DATA1__USDHC1_DATA1	0x40001382
+			MX93_PAD_SD1_DATA2__USDHC1_DATA2	0x40001382
+			MX93_PAD_SD1_DATA3__USDHC1_DATA3	0x40001382
+			MX93_PAD_SD1_DATA4__USDHC1_DATA4	0x40001382
+			MX93_PAD_SD1_DATA5__USDHC1_DATA5	0x40001382
+			MX93_PAD_SD1_DATA6__USDHC1_DATA6	0x40001382
+			MX93_PAD_SD1_DATA7__USDHC1_DATA7	0x40001382
+			MX93_PAD_SD1_STROBE__USDHC1_STROBE	0x1582
+		>;
+	};
+
+	/* need to config the SION for data and cmd pad, refer to ERR052021 */
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+		fsl,pins = <
+			MX93_PAD_SD1_CLK__USDHC1_CLK		0x158e
+			MX93_PAD_SD1_CMD__USDHC1_CMD		0x4000138e
+			MX93_PAD_SD1_DATA0__USDHC1_DATA0	0x4000138e
+			MX93_PAD_SD1_DATA1__USDHC1_DATA1	0x4000138e
+			MX93_PAD_SD1_DATA2__USDHC1_DATA2	0x4000138e
+			MX93_PAD_SD1_DATA3__USDHC1_DATA3	0x4000138e
+			MX93_PAD_SD1_DATA4__USDHC1_DATA4	0x4000138e
+			MX93_PAD_SD1_DATA5__USDHC1_DATA5	0x4000138e
+			MX93_PAD_SD1_DATA6__USDHC1_DATA6	0x4000138e
+			MX93_PAD_SD1_DATA7__USDHC1_DATA7	0x4000138e
+			MX93_PAD_SD1_STROBE__USDHC1_STROBE	0x158e
+		>;
+	};
+
+	/* need to config the SION for data and cmd pad, refer to ERR052021 */
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
 		fsl,pins = <
 			MX93_PAD_SD1_CLK__USDHC1_CLK		0x15fe
 			MX93_PAD_SD1_CMD__USDHC1_CMD		0x400013fe
@@ -420,6 +454,32 @@ MX93_PAD_SD2_CD_B__GPIO3_IO00		0x31e
 
 	/* need to config the SION for data and cmd pad, refer to ERR052021 */
 	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX93_PAD_SD2_CLK__USDHC2_CLK		0x1582
+			MX93_PAD_SD2_CMD__USDHC2_CMD		0x40001382
+			MX93_PAD_SD2_DATA0__USDHC2_DATA0	0x40001382
+			MX93_PAD_SD2_DATA1__USDHC2_DATA1	0x40001382
+			MX93_PAD_SD2_DATA2__USDHC2_DATA2	0x40001382
+			MX93_PAD_SD2_DATA3__USDHC2_DATA3	0x40001382
+			MX93_PAD_SD2_VSELECT__USDHC2_VSELECT	0x51e
+		>;
+	};
+
+	/* need to config the SION for data and cmd pad, refer to ERR052021 */
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX93_PAD_SD2_CLK__USDHC2_CLK		0x158e
+			MX93_PAD_SD2_CMD__USDHC2_CMD		0x4000138e
+			MX93_PAD_SD2_DATA0__USDHC2_DATA0	0x4000138e
+			MX93_PAD_SD2_DATA1__USDHC2_DATA1	0x4000138e
+			MX93_PAD_SD2_DATA2__USDHC2_DATA2	0x4000138e
+			MX93_PAD_SD2_DATA3__USDHC2_DATA3	0x4000138e
+			MX93_PAD_SD2_VSELECT__USDHC2_VSELECT	0x51e
+		>;
+	};
+
+	/* need to config the SION for data and cmd pad, refer to ERR052021 */
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
 		fsl,pins = <
 			MX93_PAD_SD2_CLK__USDHC2_CLK		0x15fe
 			MX93_PAD_SD2_CMD__USDHC2_CMD		0x400013fe

-- 
2.37.1