[PATCH] arm64: dts: rockchip: add PCIe3 support on rk3588-jaguar

[Heiko Stuebner]

From: Heiko Stuebner <heiko.stuebner at cherry.de>

The Jaguar SBC provides a M.2 slot connected to the pcie3 controller.
In contrast to a number of other boards the pcie-refclk is gpio-controlled,
so the necessary clock is added to the list of pcie3 clocks.

Signed-off-by: Heiko Stuebner <heiko.stuebner at cherry.de>
---
 .../arm64/boot/dts/rockchip/rk3588-jaguar.dts | 53 +++++++++++++++++++
 1 file changed, 53 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3588-jaguar.dts b/arch/arm64/boot/dts/rockchip/rk3588-jaguar.dts
index 5002105dc78e..908fbabd8b00 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588-jaguar.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3588-jaguar.dts
@@ -72,6 +72,25 @@ led-1 {
 		};
 	};
 
+	/*
+	 * 100MHz reference clock for PCIe peripherals from PI6C557-05BLE
+	 * clock generator.
+	 * The clock output is gated via the OE pin on the clock generator.
+	 * This is modeled as a fixed-clock plus a gpio-gate-clock.
+	 */
+	pcie_refclk_gen: pcie-refclk-gen-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <1000000000>;
+	};
+
+	pcie_refclk: pcie-refclk-clock {
+		compatible = "gpio-gate-clock";
+		clocks = <&pcie_refclk_gen>;
+		#clock-cells = <0>;
+		enable-gpios = <&gpio0 RK_PC6 GPIO_ACTIVE_LOW>; /* PCIE30X4_CLKREQN_M0 */
+	};
+
 	pps {
 		compatible = "pps-gpio";
 		gpios = <&gpio0 RK_PD5 GPIO_ACTIVE_HIGH>;
@@ -466,6 +485,40 @@ &pcie2x1l0 {
 	status = "okay";
 };
 
+&pcie30phy {
+	status = "okay";
+};
+
+&pcie30x4m0_pins {
+	/*
+	 * pcie30x4_clkreqn_m0 is used by the refclk generator
+	 * pcie30x4_perstn_m0 is used as via the reset-gpio
+	 */
+	rockchip,pins =
+		/* pcie30x4_waken_m0 */
+		<0 RK_PC7 12 &pcfg_pull_none>;
+};
+
+&pcie3x4 {
+	/*
+	 * The board has a gpio-controlled "pcie_refclk" generator,
+	 * so add it to the list of clocks.
+	 */
+	clocks = <&cru ACLK_PCIE_4L_MSTR>, <&cru ACLK_PCIE_4L_SLV>,
+		 <&cru ACLK_PCIE_4L_DBI>, <&cru PCLK_PCIE_4L>,
+		 <&cru CLK_PCIE_AUX0>, <&cru CLK_PCIE4L_PIPE>,
+		 <&pcie_refclk>;
+	clock-names = "aclk_mst", "aclk_slv",
+		      "aclk_dbi", "pclk",
+		      "aux", "pipe",
+		      "ref";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie30x4m0_pins>;
+	reset-gpios = <&gpio0 RK_PD0 GPIO_ACTIVE_HIGH>; /* PCIE30X4_PERSTN_M0 */
+	vpcie3v3-supply = <&vcc3v3_mdot2>;
+	status = "okay";
+};
+
 &pinctrl {
 	emmc {
 		emmc_reset: emmc-reset {
-- 
2.39.2