[PATCH 1/1] arm64: dts: imx8qxp-mek: add cm40_i2c, wm8960/wm8962 and sai[0,1,4,5]
Frank Li
Frank.Li at nxp.com
Thu Apr 4 09:19:13 PDT 2024
imx8qxp-mek use two kind audio codec, wm8960 and wm8962. Using dummy gpio
i2c bus mux to connect both i2c devices. One will probe failure and other
will probe success when devices driver check whoami. So one dtb can cover
both board configuration.
Signed-off-by: Frank Li <Frank.Li at nxp.com>
---
arch/arm64/boot/dts/freescale/imx8qxp-mek.dts | 210 ++++++++++++++++++
1 file changed, 210 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts b/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts
index 8360bb851ac03..adff87c7cf305 100644
--- a/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts
+++ b/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts
@@ -30,6 +30,13 @@ reg_usdhc2_vmmc: usdhc2-vmmc {
enable-active-high;
};
+ reg_audio: regulator-wm8962 {
+ compatible = "regulator-fixed";
+ regulator-name = "3v3_aud";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
gpio-sbu-mux {
compatible = "nxp,cbdtu02043", "gpio-sbu-mux";
pinctrl-names = "default";
@@ -44,6 +51,105 @@ usb3_data_ss: endpoint {
};
};
};
+
+ sound-wm8960 {
+ compatible = "fsl,imx-audio-wm8960";
+ model = "wm8960-audio";
+ audio-cpu = <&sai1>;
+ audio-codec = <&wm8960>;
+ hp-det-gpio = <&lsio_gpio1 0 GPIO_ACTIVE_HIGH>;
+ audio-routing =
+ "Headphone Jack", "HP_L",
+ "Headphone Jack", "HP_R",
+ "Ext Spk", "SPK_LP",
+ "Ext Spk", "SPK_LN",
+ "Ext Spk", "SPK_RP",
+ "Ext Spk", "SPK_RN",
+ "LINPUT1", "Mic Jack",
+ "Mic Jack", "MICB";
+ };
+
+ sound-wm8962 {
+ compatible = "fsl,imx-audio-wm8962";
+ model = "wm8962-audio";
+ audio-cpu = <&sai1>;
+ audio-codec = <&wm8962>;
+ hp-det-gpio = <&lsio_gpio1 0 GPIO_ACTIVE_HIGH>;
+ audio-routing =
+ "Headphone Jack", "HPOUTL",
+ "Headphone Jack", "HPOUTR",
+ "Ext Spk", "SPKOUTL",
+ "Ext Spk", "SPKOUTR",
+ "AMIC", "MICBIAS",
+ "IN3R", "AMIC",
+ "IN1R", "AMIC";
+ };
+
+ /*
+ * This dummy i2c mux. GPIO actually will not impact selection. At actual boards, only 1
+ * device connectted. I2C client driver will check ID when probe. Only matched ID's driver
+ * probe successfully.
+ */
+ i2cvmux: i2cmux {
+ compatible = "i2c-mux-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ mux-gpios = <&lsio_gpio5 0 GPIO_ACTIVE_HIGH>; /* use an unused gpio */
+ i2c-parent = <&cm40_i2c>;
+
+ i2c at 0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* WCPU boards SCH-54536 */
+ wm8962: wm8962 at 1a {
+ compatible = "wlf,wm8962";
+ reg = <0x1a>;
+ clocks = <&mclkout0_lpcg IMX_LPCG_CLK_0>;
+ assigned-clocks = <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_PLL>,
+ <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_SLV_BUS>,
+ <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_MST_BUS>,
+ <&mclkout0_lpcg IMX_LPCG_CLK_0>;
+ assigned-clock-rates = <786432000>,
+ <49152000>,
+ <12288000>,
+ <12288000>;
+ DCVDD-supply = <®_audio>;
+ DBVDD-supply = <®_audio>;
+ AVDD-supply = <®_audio>;
+ CPVDD-supply = <®_audio>;
+ MICVDD-supply = <®_audio>;
+ PLLVDD-supply = <®_audio>;
+ SPKVDD1-supply = <®_audio>;
+ SPKVDD2-supply = <®_audio>;
+ };
+ };
+
+ i2c at 1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ wm8960: wm8960 at 1a {
+ compatible = "wlf,wm8960";
+ reg = <0x1a>;
+ clocks = <&mclkout0_lpcg IMX_LPCG_CLK_0>;
+ clock-names = "mclk";
+ wlf,shared-lrclk;
+ wlf,hp-cfg = <2 2 3>;
+ wlf,gpio-cfg = <1 3>;
+ assigned-clocks = <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_PLL>,
+ <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_SLV_BUS>,
+ <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_MST_BUS>,
+ <&mclkout0_lpcg IMX_LPCG_CLK_0>;
+ assigned-clock-rates = <786432000>,
+ <49152000>,
+ <12288000>,
+ <12288000>;
+ };
+ };
+ };
};
&dsp {
@@ -188,6 +294,29 @@ typec_con_ss: endpoint {
};
+&cm40_i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-frequency = <100000>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_cm40_i2c>;
+ pinctrl-1 = <&pinctrl_cm40_i2c_gpio>;
+ scl-gpios = <&lsio_gpio1 10 GPIO_ACTIVE_HIGH>;
+ sda-gpios = <&lsio_gpio1 9 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+
+ pca6416: gpio at 20 {
+ compatible = "ti,tca6416";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+};
+
+&cm40_intmux {
+ status = "okay";
+};
+
&lpuart0 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_lpuart0>;
@@ -218,6 +347,53 @@ &scu_key {
status = "okay";
};
+&sai0 {
+ #sound-dai-cells = <0>;
+ assigned-clocks = <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_PLL>,
+ <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_SLV_BUS>,
+ <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_MST_BUS>,
+ <&sai0_lpcg IMX_LPCG_CLK_0>;
+ assigned-clock-rates = <786432000>, <49152000>, <12288000>, <49152000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sai0>;
+ status = "okay";
+};
+
+&sai1 {
+ assigned-clocks = <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_PLL>,
+ <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_SLV_BUS>,
+ <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_MST_BUS>,
+ <&sai1_lpcg IMX_LPCG_CLK_0>;
+ assigned-clock-rates = <786432000>, <49152000>, <12288000>, <49152000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sai1>;
+ status = "okay";
+};
+
+&sai4 {
+ assigned-clocks = <&acm IMX_ADMA_ACM_SAI4_MCLK_SEL>,
+ <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_PLL>,
+ <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_SLV_BUS>,
+ <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_MST_BUS>,
+ <&sai4_lpcg IMX_LPCG_CLK_0>;
+ assigned-clock-parents = <&aud_pll_div1_lpcg IMX_LPCG_CLK_0>;
+ assigned-clock-rates = <0>, <786432000>, <98304000>, <12288000>, <98304000>;
+ fsl,sai-asynchronous;
+ status = "okay";
+};
+
+&sai5 {
+ assigned-clocks = <&acm IMX_ADMA_ACM_SAI5_MCLK_SEL>,
+ <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_PLL>,
+ <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_SLV_BUS>,
+ <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_MST_BUS>,
+ <&sai5_lpcg IMX_LPCG_CLK_0>;
+ assigned-clock-parents = <&aud_pll_div1_lpcg IMX_LPCG_CLK_0>;
+ assigned-clock-rates = <0>, <786432000>, <98304000>, <12288000>, <98304000>;
+ fsl,sai-asynchronous;
+ status = "okay";
+};
+
&thermal_zones {
pmic-thermal {
polling-delay-passive = <250>;
@@ -314,6 +490,21 @@ &vpu_core1 {
};
&iomuxc {
+
+ pinctrl_cm40_i2c: cm40i2cgrp {
+ fsl,pins = <
+ IMX8QXP_ADC_IN1_M40_I2C0_SDA 0x0600004c
+ IMX8QXP_ADC_IN0_M40_I2C0_SCL 0x0600004c
+ >;
+ };
+
+ pinctrl_cm40_i2c_gpio: cm40i2cgpio-grp {
+ fsl,pins = <
+ IMX8QXP_ADC_IN1_LSIO_GPIO1_IO09 0xc600004c
+ IMX8QXP_ADC_IN0_LSIO_GPIO1_IO10 0xc600004c
+ >;
+ };
+
pinctrl_fec1: fec1grp {
fsl,pins = <
IMX8QXP_ENET0_MDC_CONN_ENET0_MDC 0x06000020
@@ -385,6 +576,25 @@ IMX8QXP_ENET0_REFCLK_125M_25M_LSIO_GPIO5_IO09 0x60
>;
};
+ pinctrl_sai0: sai0grp {
+ fsl,pins = <
+ IMX8QXP_SAI0_TXD_ADMA_SAI0_TXD 0x06000060
+ IMX8QXP_SAI0_RXD_ADMA_SAI0_RXD 0x06000040
+ IMX8QXP_SAI0_TXC_ADMA_SAI0_TXC 0x06000040
+ IMX8QXP_SAI0_TXFS_ADMA_SAI0_TXFS 0x06000040
+ >;
+ };
+
+ pinctrl_sai1: sai1grp {
+ fsl,pins = <
+ IMX8QXP_SAI1_RXD_ADMA_SAI1_RXD 0x06000040
+ IMX8QXP_SAI1_RXC_ADMA_SAI1_TXC 0x06000040
+ IMX8QXP_SAI1_RXFS_ADMA_SAI1_TXFS 0x06000040
+ IMX8QXP_SPI0_CS1_ADMA_SAI1_TXD 0x06000060
+ IMX8QXP_SPI2_CS0_LSIO_GPIO1_IO00 0x06000040
+ >;
+ };
+
pinctrl_usdhc1: usdhc1grp {
fsl,pins = <
IMX8QXP_EMMC0_CLK_CONN_EMMC0_CLK 0x06000041
--
2.34.1
More information about the linux-arm-kernel
mailing list