[PATCH 2/2] arm64: dts: rockchip: add Protonic MECSBC device-tree

Heiko Stübner heiko at sntech.de
Thu Apr 4 01:56:24 PDT 2024


Hi Sascha,

Am Donnerstag, 4. April 2024, 10:34:40 CEST schrieb Sascha Hauer:
> From: David Jander <david at protonic.nl>
> 
> MECSBC is a single board computer for blood analysis machines from
> RR-Mechatronics, designed and manufactured by Protonic Holland, based on
> the Rockchip RK3568 SoC.
> 
> Signed-off-by: David Jander <david at protonic.nl>
> Signed-off-by: Sascha Hauer <s.hauer at pengutronix.de>
> ---
>  arch/arm64/boot/dts/rockchip/Makefile          |   1 +
>  arch/arm64/boot/dts/rockchip/rk3568-mecsbc.dts | 394 +++++++++++++++++++++++++
>  2 files changed, 395 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> index f906a868b71ac..1152e0f6a25cb 100644
> --- a/arch/arm64/boot/dts/rockchip/Makefile
> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> @@ -104,6 +104,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-nanopi-r5c.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-nanopi-r5s.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-odroid-m1.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-qnap-ts433.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-mecsbc.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-radxa-e25.dtb

alphabetical sorting of entries please

>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-roc-pc.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-rock-3a.dtb
> diff --git a/arch/arm64/boot/dts/rockchip/rk3568-mecsbc.dts b/arch/arm64/boot/dts/rockchip/rk3568-mecsbc.dts
> new file mode 100644
> index 0000000000000..e50d135042ec7
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3568-mecsbc.dts
> @@ -0,0 +1,394 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +
> +/dts-v1/;
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/pinctrl/rockchip.h>
> +#include <dt-bindings/pwm/pwm.h>
> +#include "rk3568.dtsi"
> +
> +/ {
> +	model = "Protonic MECSBC";
> +	compatible = "prt,mecsbc", "rockchip,rk3568";
> +
> +	aliases {
> +		mmc0 = &sdhci;
> +		mmc1 = &sdmmc0;
> +	};
> +
> +	chosen: chosen {
> +		stdout-path = "serial2:1500000n8";
> +	};
> +
> +	tas2562-sound {
> +		compatible = "simple-audio-card";
> +		simple-audio-card,format = "i2s";
> +		simple-audio-card,name = "Speaker";
> +		simple-audio-card,mclk-fs = <256>;
> +
> +		simple-audio-card,cpu {
> +			sound-dai = <&i2s1_8ch>;
> +		};
> +
> +		simple-audio-card,codec {
> +			sound-dai = <&tas2562>;
> +		};
> +	};
> +
> +	vdd_gpu: regulator-vdd-gpu {
> +		compatible = "pwm-regulator";
> +		pwms = <&pwm1 0 5000 PWM_POLARITY_INVERTED>;
> +		regulator-name = "vdd_gpu";
> +		regulator-min-microvolt = <915000>;
> +		regulator-max-microvolt = <1000000>;
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-settling-time-up-us = <250>;
> +		pwm-dutycycle-range = <0 100>; /* dutycycle inverted 0% => 0.915V */
> +	};
> +
> +	vdd_npu: regulator-vdd-npu {
> +		compatible = "pwm-regulator";
> +		pwms = <&pwm2 0 5000 PWM_POLARITY_INVERTED>;
> +		regulator-name = "vdd_npu";
> +		regulator-min-microvolt = <915000>;
> +		regulator-max-microvolt = <1000000>;
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-settling-time-up-us = <250>;
> +		pwm-dutycycle-range = <0 100>; /* dutycycle inverted 0% => 0.915V */
> +	};
> +
> +	p3v3: p3v3-regulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "p3v3";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +	};
> +
> +	p1v8: p1v8-regulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "p1v8";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +	};

please sort alphabetical by node-name

> +};
> +
> +&combphy0 {
> +	status = "okay";
> +};
> +
> +&combphy1 {
> +	status = "okay";
> +};
> +
> +&combphy2 {
> +	status = "okay";
> +};
> +
> +&cpu0 {
> +	cpu-supply = <&vdd_cpu>;
> +};
> +
> +&cpu1 {
> +	cpu-supply = <&vdd_cpu>;
> +};
> +
> +&cpu2 {
> +	cpu-supply = <&vdd_cpu>;
> +};
> +
> +&cpu3 {
> +	cpu-supply = <&vdd_cpu>;
> +};
> +
> +&gmac1 {
> +	assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
> +	assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru CLK_MAC1_2TOP>;
> +	phy-handle = <&rgmii_phy1>;
> +	phy-mode = "rgmii";
> +	clock_in_out = "output";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&gmac1m1_miim
> +		     &gmac1m1_tx_bus2
> +		     &gmac1m1_rx_bus2
> +		     &gmac1m1_rgmii_clk
> +		     &gmac1m1_clkinout
> +		     &gmac1m1_rgmii_bus>;
> +	status = "okay";
> +	tx_delay = <0x30>;
> +	rx_delay = <0x10>;
> +};
> +
> +&gpu {
> +	mali-supply = <&vdd_gpu>;
> +	status = "okay";
> +};
> +
> +&i2c0 {
> +	status = "okay";
> +
> +	vdd_cpu: regulator at 60 {
> +		compatible = "fcs,fan53555";
> +		reg = <0x60>;
> +		fcs,suspend-voltage-selector = <1>;
> +		regulator-name = "vdd_cpu";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <800000>;
> +		regulator-max-microvolt = <1150000>;
> +		regulator-ramp-delay = <2300>;
> +
> +		regulator-state-mem {
> +			regulator-off-in-suspend;
> +		};
> +	};
> +};
> +
> +&i2c2 {
> +	status = "okay";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c2m0_xfer>;
> +};
> +
> +&i2c3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c3m0_xfer>;
> +	status = "okay";
> +
> +	tas2562: tas2562 at 4c {
> +		compatible = "ti,tas2562";
> +		reg = <0x4c>;
> +		#sound-dai-cells = <0>;
> +		shutdown-gpios = <&gpio1 RK_PD4 GPIO_ACTIVE_HIGH>;
> +		interrupt-parent = <&gpio1>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_tas2562>;
> +		interrupts = <RK_PD1 IRQ_TYPE_LEVEL_LOW>;
> +		ti,imon-slot-no = <0>;
> +	};
> +};
> +
> +&i2c5 {
> +	status = "okay";
> +
> +	tmp1075n at 48 {
> +		compatible = "ti,tmp1075";
> +		reg = <0x48>;
> +	};
> +
> +	pcf8563: rtc at 51 {
> +		compatible = "nxp,pcf85363";
> +		reg = <0x51>;
> +		#clock-cells = <0>;
> +		clock-output-names = "rtcic_32kout";
> +	};
> +};
> +
> +&i2s1_8ch {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2s1m0_sclktx &i2s1m0_lrcktx &i2s1m0_sdi0 &i2s1m0_sdo0>;
> +	rockchip,trcm-sync-tx-only;
> +	status = "okay";
> +};
> +
> +&mdio1 {
> +	rgmii_phy1: ethernet-phy at 2 {
> +		compatible = "ethernet-phy-ieee802.3-c22";
> +		reg = <0x2>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&eth_phy1_rst>;
> +		reset-assert-us = <20000>;
> +		reset-deassert-us = <100000>;
> +		reset-gpios = <&gpio4 RK_PB3 GPIO_ACTIVE_LOW>;
> +	};
> +};
> +
> +&pcie2x1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pcie20m1_pins>;
> +	reset-gpios = <&gpio3 RK_PC1 GPIO_ACTIVE_HIGH>;
> +	status = "okay";
> +};
> +
> +&pcie30phy {
> +	status = "okay";
> +};
> +
> +&pcie3x2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pcie30x2m1_pins>;
> +	reset-gpios = <&gpio2 RK_PD6 GPIO_ACTIVE_HIGH>;
> +	vpcie3v3-supply = <&p3v3>;
> +	status = "okay";
> +};
> +
> +&pinctrl {
> +	ethernet {
> +		eth_phy1_rst: eth_phy1_rst {
> +			rockchip,pins = <4 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +	};
> +
> +	tas2562 {
> +		pinctrl_tas2562: tas2562 {
> +			rockchip,pins = <1 RK_PD4 RK_FUNC_GPIO &pcfg_pull_up>;
> +		};
> +	};
> +};
> +
> +&pmu_io_domains {
> +	pmuio1-supply = <&p3v3>;
> +	pmuio2-supply = <&p3v3>;
> +	vccio1-supply = <&p1v8>;
> +	vccio2-supply = <&p1v8>;
> +	vccio3-supply = <&p3v3>;
> +	vccio4-supply = <&p1v8>;
> +	vccio5-supply = <&p3v3>;
> +	vccio6-supply = <&p1v8>;
> +	vccio7-supply = <&p3v3>;
> +	status = "okay";
> +};
> +
> +&saradc {
> +	vref-supply = <&p1v8>;
> +	status = "okay";
> +};
> +
> +&sdhci {
> +	bus-width = <8>;
> +	max-frequency = <200000000>;
> +	non-removable;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
> +	vmmc-supply = <&p3v3>;
> +	vqmmc-supply = <&p1v8>;
> +	mmc-hs200-1_8v;
> +	non-removable;
> +	no-sd;
> +	no-sdio;
> +	status = "okay";
> +};
> +
> +&sdmmc0 {
> +	bus-width = <4>;
> +	cap-sd-highspeed;
> +	cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
> +	disable-wp;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
> +	sd-uhs-sdr50;
> +	vmmc-supply = <&p3v3>;
> +	vqmmc-supply = <&p3v3>;
> +	status = "okay";
> +};
> +
> +&tsadc {
> +	rockchip,hw-tshut-mode = <1>;
> +	rockchip,hw-tshut-polarity = <0>;
> +	status = "okay";
> +};
> +
> +&uart2 {
> +	status = "okay";
> +};
> +
> +&usb_host0_ehci {
> +	status = "okay";
> +};
> +
> +&usb_host0_ohci {
> +	status = "okay";
> +};
> +
> +&usb_host0_xhci {
> +	extcon = <&usb2phy0>;
> +	status = "okay";
> +	dr_mode = "host";

please sort properties alphabetical, with
compatible at the top and status last.


> +};
> +
> +&usb_host1_ehci {
> +	status = "okay";
> +};
> +
> +&usb_host1_ohci {
> +	status = "okay";
> +};
> +
> +&usb_host1_xhci {
> +	status = "okay";
> +};
> +
> +&usb2phy0 {
> +	status = "okay";
> +};
> +
> +&usb2phy0_host {
> +	status = "okay";
> +};
> +
> +&usb2phy0_otg {
> +	status = "okay";
> +};
> +
> +&usb2phy1 {
> +	status = "okay";
> +};
> +
> +&usb2phy1_host {
> +	status = "okay";
> +};
> +
> +&usb2phy1_otg {
> +	status = "okay";
> +};
> +
> +&pwm1 {
> +	status = "okay";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pwm1m0_pins>;
> +};
> +
> +&pwm2 {
> +	status = "okay";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pwm2m0_pins>;
> +};

please sort phandles "&pwm2" alphabetical and status comes last


> +
> +&gpu_opp_table {
> +	compatible = "operating-points-v2";
> +
> +	opp-200000000 {
> +		opp-hz = /bits/ 64 <200000000>;
> +		opp-microvolt = <915000>;
> +	};
> +
> +	opp-300000000 {
> +		opp-hz = /bits/ 64 <300000000>;
> +		opp-microvolt = <915000>;
> +	};
> +
> +	opp-400000000 {
> +		opp-hz = /bits/ 64 <400000000>;
> +		opp-microvolt = <915000>;
> +	};
> +
> +	opp-600000000 {
> +		opp-hz = /bits/ 64 <600000000>;
> +		opp-microvolt = <920000>;
> +	};
> +
> +	opp-700000000 {
> +		opp-hz = /bits/ 64 <700000000>;
> +		opp-microvolt = <950000>;
> +	};
> +
> +	opp-800000000 {
> +		opp-hz = /bits/ 64 <800000000>;
> +		opp-microvolt = <1000000>;
> +	};
> +};

a comment would be nice, why the OPPs get changed


Heiko





More information about the linux-arm-kernel mailing list