[PATCH v9 4/4] PCI: brcmstb: Configure HW CLKREQ# mode appropriate for downstream device
Jim Quinlan
james.quinlan at broadcom.com
Wed Apr 3 14:39:01 PDT 2024
The Broadcom STB/CM PCIe HW core, which is also used in RPi SOCs, must be
deliberately set by the PCIe RC HW into one of three mutually exclusive
modes:
"safe" -- No CLKREQ# expected or required, refclk is always provided. This
mode should work for all devices but is not be capable of any refclk
power savings.
"no-l1ss" -- CLKREQ# is expected to be driven by the downstream device for
CPM and ASPM L0s and L1. Provides Clock Power Management, L0s, and L1,
but cannot provide L1 substate (L1SS) power savings. If the downstream
device connected to the RC is L1SS capable AND the OS enables L1SS, all
PCIe traffic may abruptly halt, potentially hanging the system.
"default" -- Bidirectional CLKREQ# between the RC and downstream device.
Provides ASPM L0s, L1, and L1SS, but not compliant to provide Clock
Power Management; specifically, may not be able to meet the T_CLRon max
timing of 400ns as specified in "Dynamic Clock Control", section
3.2.5.2.2 of the PCIe Express Mini CEM 2.1 specification. This
situation is atypical and should happen only with older devices.
Previously, this driver always set the mode to "no-l1ss", as almost all
STB/CM boards operate in this mode. But now there is interest in
activating L1SS power savings from STB/CM customers, which requires
"default" mode. In addition, a bug was filed for RPi4 CM platform because
most devices did not work in "no-l1ss" mode (see link below).
Note that the mode is specified by the DT property "brcm,clkreq-mode". If
this property is omitted, then "default" mode is chosen.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217276
Signed-off-by: Jim Quinlan <james.quinlan at broadcom.com>
---
drivers/pci/controller/pcie-brcmstb.c | 79 ++++++++++++++++++++++++---
1 file changed, 70 insertions(+), 9 deletions(-)
diff --git a/drivers/pci/controller/pcie-brcmstb.c b/drivers/pci/controller/pcie-brcmstb.c
index 3d08b92d5bb8..3dc8511e6f58 100644
--- a/drivers/pci/controller/pcie-brcmstb.c
+++ b/drivers/pci/controller/pcie-brcmstb.c
@@ -48,6 +48,9 @@
#define PCIE_RC_CFG_PRIV1_LINK_CAPABILITY 0x04dc
#define PCIE_RC_CFG_PRIV1_LINK_CAPABILITY_ASPM_SUPPORT_MASK 0xc00
+#define PCIE_RC_CFG_PRIV1_ROOT_CAP 0x4f8
+#define PCIE_RC_CFG_PRIV1_ROOT_CAP_L1SS_MODE_MASK 0xf8
+
#define PCIE_RC_DL_MDIO_ADDR 0x1100
#define PCIE_RC_DL_MDIO_WR_DATA 0x1104
#define PCIE_RC_DL_MDIO_RD_DATA 0x1108
@@ -121,9 +124,12 @@
#define PCIE_MISC_HARD_PCIE_HARD_DEBUG 0x4204
#define PCIE_MISC_HARD_PCIE_HARD_DEBUG_CLKREQ_DEBUG_ENABLE_MASK 0x2
+#define PCIE_MISC_HARD_PCIE_HARD_DEBUG_L1SS_ENABLE_MASK 0x200000
#define PCIE_MISC_HARD_PCIE_HARD_DEBUG_SERDES_IDDQ_MASK 0x08000000
#define PCIE_BMIPS_MISC_HARD_PCIE_HARD_DEBUG_SERDES_IDDQ_MASK 0x00800000
-
+#define PCIE_CLKREQ_MASK \
+ (PCIE_MISC_HARD_PCIE_HARD_DEBUG_CLKREQ_DEBUG_ENABLE_MASK | \
+ PCIE_MISC_HARD_PCIE_HARD_DEBUG_L1SS_ENABLE_MASK)
#define PCIE_INTR2_CPU_BASE 0x4300
#define PCIE_MSI_INTR2_BASE 0x4500
@@ -1100,13 +1106,73 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
return 0;
}
+static void brcm_config_clkreq(struct brcm_pcie *pcie)
+{
+ static const char err_msg[] = "invalid 'brcm,clkreq-mode' DT string\n";
+ const char *mode = "default";
+ u32 clkreq_cntl;
+ int ret, tmp;
+
+ ret = of_property_read_string(pcie->np, "brcm,clkreq-mode", &mode);
+ if (ret && ret != -EINVAL) {
+ dev_err(pcie->dev, err_msg);
+ mode = "safe";
+ }
+
+ /* Start out assuming safe mode (both mode bits cleared) */
+ clkreq_cntl = readl(pcie->base + PCIE_MISC_HARD_PCIE_HARD_DEBUG);
+ clkreq_cntl &= ~PCIE_CLKREQ_MASK;
+
+ if (strcmp(mode, "no-l1ss") == 0) {
+ /*
+ * "no-l1ss" -- Provides Clock Power Management, L0s, and
+ * L1, but cannot provide L1 substate (L1SS) power
+ * savings. If the downstream device connected to the RC is
+ * L1SS capable AND the OS enables L1SS, all PCIe traffic
+ * may abruptly halt, potentially hanging the system.
+ */
+ clkreq_cntl |= PCIE_MISC_HARD_PCIE_HARD_DEBUG_CLKREQ_DEBUG_ENABLE_MASK;
+ /*
+ * We want to un-advertise L1 substates because if the OS
+ * tries to configure the controller into using L1 substate
+ * power savings it may fail or hang when the RC HW is in
+ * "no-l1ss" mode.
+ */
+ tmp = readl(pcie->base + PCIE_RC_CFG_PRIV1_ROOT_CAP);
+ u32p_replace_bits(&tmp, 2, PCIE_RC_CFG_PRIV1_ROOT_CAP_L1SS_MODE_MASK);
+ writel(tmp, pcie->base + PCIE_RC_CFG_PRIV1_ROOT_CAP);
+
+ } else if (strcmp(mode, "default") == 0) {
+ /*
+ * "default" -- Provides L0s, L1, and L1SS, but not
+ * compliant to provide Clock Power Management;
+ * specifically, may not be able to meet the Tclron max
+ * timing of 400ns as specified in "Dynamic Clock Control",
+ * section 3.2.5.2.2 of the PCIe spec. This situation is
+ * atypical and should happen only with older devices.
+ */
+ clkreq_cntl |= PCIE_MISC_HARD_PCIE_HARD_DEBUG_L1SS_ENABLE_MASK;
+
+ } else {
+ /*
+ * "safe" -- No power savings; refclk is driven by RC
+ * unconditionally.
+ */
+ if (strcmp(mode, "safe") != 0)
+ dev_err(pcie->dev, err_msg);
+ mode = "safe";
+ }
+ writel(clkreq_cntl, pcie->base + PCIE_MISC_HARD_PCIE_HARD_DEBUG);
+
+ dev_info(pcie->dev, "clkreq-mode set to %s\n", mode);
+}
+
static int brcm_pcie_start_link(struct brcm_pcie *pcie)
{
struct device *dev = pcie->dev;
void __iomem *base = pcie->base;
u16 nlw, cls, lnksta;
bool ssc_good = false;
- u32 tmp;
int ret, i;
/* Unassert the fundamental reset */
@@ -1138,6 +1204,8 @@ static int brcm_pcie_start_link(struct brcm_pcie *pcie)
*/
brcm_extend_internal_bus_timeout(pcie, BRCM_LTR_MAX_NS + 1000);
+ brcm_config_clkreq(pcie);
+
if (pcie->gen)
brcm_pcie_set_gen(pcie, pcie->gen);
@@ -1156,13 +1224,6 @@ static int brcm_pcie_start_link(struct brcm_pcie *pcie)
pci_speed_string(pcie_link_speed[cls]), nlw,
ssc_good ? "(SSC)" : "(!SSC)");
- /*
- * Refclk from RC should be gated with CLKREQ# input when ASPM L0s,L1
- * is enabled => setting the CLKREQ_DEBUG_ENABLE field to 1.
- */
- tmp = readl(base + PCIE_MISC_HARD_PCIE_HARD_DEBUG);
- tmp |= PCIE_MISC_HARD_PCIE_HARD_DEBUG_CLKREQ_DEBUG_ENABLE_MASK;
- writel(tmp, base + PCIE_MISC_HARD_PCIE_HARD_DEBUG);
return 0;
}
--
2.17.1
-------------- next part --------------
A non-text attachment was scrubbed...
Name: smime.p7s
Type: application/pkcs7-signature
Size: 4210 bytes
Desc: S/MIME Cryptographic Signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20240403/b021abff/attachment-0001.p7s>
More information about the linux-arm-kernel
mailing list