[PATCH v10 03/11] arm64: dts: imx8ulp-evk: enable usb nodes and add ptn5150 nodes

[Shawn Guo]

On Thu, Mar 21, 2024 at 04:14:31PM +0800, Xu Yang wrote:
> Enable 2 USB nodes and add 2 PTN5150 nodes on i.MX8ULP evk board.
> 
> Signed-off-by: Xu Yang <xu.yang_2 at nxp.com>
> 
> ---
> Changes in v2:
>  - fix format as suggusted by Fabio
>  - add PTN5150 nodes
> Changes in v3:
>  - no changes
> Changes in v4:
>  - no changes
> Changes in v5:
>  - no changes
> Changes in v6:
>  - no changes
> Changes in v7:
>  - no changes
> Changes in v8:
>  - no changes
> Changes in v9:
>  - no changes
> Changes in v10:
>  - no changes
> ---
>  arch/arm64/boot/dts/freescale/imx8ulp-evk.dts | 84 +++++++++++++++++++
>  1 file changed, 84 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts b/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts
> index 69dd8e31027c..bf418af31039 100644
> --- a/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts
> +++ b/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts
> @@ -133,6 +133,64 @@ pcal6408: gpio at 21 {
>  		gpio-controller;
>  		#gpio-cells = <2>;
>  	};
> +
> +	ptn5150_1: typec at 1d {

Could you sort devices in unit-address?

> +		compatible = "nxp,ptn5150";
> +		reg = <0x1d>;
> +		int-gpios = <&gpiof 3 IRQ_TYPE_EDGE_FALLING>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_typec1>;
> +		status = "disabled";
> +	};
> +
> +	ptn5150_2: typec at 3d {
> +		compatible = "nxp,ptn5150";
> +		reg = <0x3d>;
> +		int-gpios = <&gpiof 5 IRQ_TYPE_EDGE_FALLING>;
> +			pinctrl-names = "default";

Broken indent?

Shawn

> +		pinctrl-0 = <&pinctrl_typec2>;
> +		status = "disabled";
> +	};
> +};
> +
> +&usbotg1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usb1>;
> +	dr_mode = "otg";
> +	hnp-disable;
> +	srp-disable;
> +	adp-disable;
> +	over-current-active-low;
> +	status = "okay";
> +};
> +
> +&usbphy1 {
> +	fsl,tx-d-cal = <110>;
> +	status = "okay";
> +};
> +
> +&usbmisc1 {
> +	status = "okay";
> +};
> +
> +&usbotg2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usb2>;
> +	dr_mode = "otg";
> +	hnp-disable;
> +	srp-disable;
> +	adp-disable;
> +	over-current-active-low;
> +	status = "okay";
> +};
> +
> +&usbphy2 {
> +	fsl,tx-d-cal = <110>;
> +	status = "okay";
> +};
> +
> +&usbmisc2 {
> +	status = "okay";
>  };
>  
>  &usdhc0 {
> @@ -224,6 +282,32 @@ MX8ULP_PAD_PTE13__LPI2C7_SDA	0x20
>  		>;
>  	};
>  
> +	pinctrl_typec1: typec1grp {
> +		fsl,pins = <
> +			MX8ULP_PAD_PTF3__PTF3           0x3
> +		>;
> +	};
> +
> +	pinctrl_typec2: typec2grp {
> +		fsl,pins = <
> +			MX8ULP_PAD_PTF5__PTF5           0x3
> +		>;
> +	};
> +
> +	pinctrl_usb1: usb1grp {
> +		fsl,pins = <
> +			MX8ULP_PAD_PTF2__USB0_ID	0x10003
> +			MX8ULP_PAD_PTF4__USB0_OC	0x10003
> +		>;
> +	};
> +
> +	pinctrl_usb2: usb2grp {
> +		fsl,pins = <
> +			MX8ULP_PAD_PTD23__USB1_ID	0x10003
> +			MX8ULP_PAD_PTF6__USB1_OC	0x10003
> +		>;
> +	};
> +
>  	pinctrl_usdhc0: usdhc0grp {
>  		fsl,pins = <
>  			MX8ULP_PAD_PTD1__SDHC0_CMD	0x3
> -- 
> 2.34.1
>