[PATCH 5/6] arm64: dts: marvell: cn9130-crb: drop wrong unit-addresses

[Krzysztof Kozlowski]

Top-level nodes, not being on MMIO bus, do not have "reg" properties and
should not have unit addresses.  Correct their name as well to match
"Generic node names" recommendation from Devicetree specification.
This also fixes dtc W=1 warnings:

  cn9130-crb.dtsi:29.35-37.4: Warning (unit_address_vs_reg): /ap0_mmc_vccq at 0: node has a unit name, but no reg or ranges property
  cn9130-crb.dtsi:39.38-46.4: Warning (unit_address_vs_reg): /cp0_usb3_vbus at 1: node has a unit name, but no reg or ranges property
  cn9130-crb.dtsi:57.33-65.4: Warning (unit_address_vs_reg): /cp0_sd_vccq at 0: node has a unit name, but no reg or ranges property
  cn9130-crb.dtsi:67.31-75.4: Warning (unit_address_vs_reg): /cp0_sd_vcc at 0: node has a unit name, but no reg or ranges property

Signed-off-by: Krzysztof Kozlowski <krzk at kernel.org>
---
 arch/arm64/boot/dts/marvell/cn9130-crb.dtsi | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi b/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
index 6fcc34f7b464..d48dd6bca6e5 100644
--- a/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
+++ b/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
@@ -26,7 +26,7 @@ memory at 0 {
 		reg = <0x0 0x0 0x0 0x80000000>;
 	};
 
-	ap0_reg_mmc_vccq: ap0_mmc_vccq at 0 {
+	ap0_reg_mmc_vccq: regulator-1 {
 		compatible = "regulator-gpio";
 		regulator-name = "ap0_mmc_vccq";
 		regulator-min-microvolt = <1800000>;
@@ -36,7 +36,7 @@ ap0_reg_mmc_vccq: ap0_mmc_vccq at 0 {
 			  3300000 0x0>;
 	};
 
-	cp0_reg_usb3_vbus1: cp0_usb3_vbus at 1 {
+	cp0_reg_usb3_vbus1: regulator-2 {
 		compatible = "regulator-fixed";
 		regulator-name = "cp0-xhci1-vbus";
 		regulator-min-microvolt = <5000000>;
@@ -45,16 +45,16 @@ cp0_reg_usb3_vbus1: cp0_usb3_vbus at 1 {
 		gpio = <&expander0 8 GPIO_ACTIVE_HIGH>;
 	};
 
-	cp0_usb3_0_phy0: cp0_usb3_phy0 {
+	cp0_usb3_0_phy0: usb-phy-1 {
 		compatible = "usb-nop-xceiv";
 	};
 
-	cp0_usb3_0_phy1: cp0_usb3_phy1 {
+	cp0_usb3_0_phy1: usb-phy-2 {
 		compatible = "usb-nop-xceiv";
 		vcc-supply = <&cp0_reg_usb3_vbus1>;
 	};
 
-	cp0_reg_sd_vccq: cp0_sd_vccq at 0 {
+	cp0_reg_sd_vccq: regulator-3 {
 		compatible = "regulator-gpio";
 		regulator-name = "cp0_sd_vccq";
 		regulator-min-microvolt = <1800000>;
@@ -64,7 +64,7 @@ cp0_reg_sd_vccq: cp0_sd_vccq at 0 {
 			  3300000 0x0>;
 	};
 
-	cp0_reg_sd_vcc: cp0_sd_vcc at 0 {
+	cp0_reg_sd_vcc: regulator-4 {
 		compatible = "regulator-fixed";
 		regulator-name = "cp0_sd_vcc";
 		regulator-min-microvolt = <3300000>;
-- 
2.34.1