[PATCH v2 09/12] riscv: dts: starfive: jh7100: Add sysmain and gmac DT nodes

Cristian Ciocaltea cristian.ciocaltea at collabora.com
Mon Nov 27 16:46:27 PST 2023


On 11/26/23 23:15, Emil Renner Berthing wrote:
> Cristian Ciocaltea wrote:
>> Provide the sysmain and gmac DT nodes supporting the DWMAC found on the
>> StarFive JH7100 SoC.
>>
>> Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea at collabora.com>
>> ---
>>  arch/riscv/boot/dts/starfive/jh7100.dtsi | 36 ++++++++++++++++++++++++
>>  1 file changed, 36 insertions(+)
>>
>> diff --git a/arch/riscv/boot/dts/starfive/jh7100.dtsi b/arch/riscv/boot/dts/starfive/jh7100.dtsi
>> index a8a5bb00b0d8..e8228e96d350 100644
>> --- a/arch/riscv/boot/dts/starfive/jh7100.dtsi
>> +++ b/arch/riscv/boot/dts/starfive/jh7100.dtsi
>> @@ -179,6 +179,37 @@ plic: interrupt-controller at c000000 {
>>  			riscv,ndev = <133>;
>>  		};
>>
>> +		gmac: ethernet at 10020000 {
>> +			compatible = "starfive,jh7100-dwmac", "snps,dwmac";
>> +			reg = <0x0 0x10020000 0x0 0x10000>;
>> +			clocks = <&clkgen JH7100_CLK_GMAC_ROOT_DIV>,
>> +				 <&clkgen JH7100_CLK_GMAC_AHB>,
>> +				 <&clkgen JH7100_CLK_GMAC_PTP_REF>,
>> +				 <&clkgen JH7100_CLK_GMAC_TX_INV>,
>> +				 <&clkgen JH7100_CLK_GMAC_GTX>;
>> +			clock-names = "stmmaceth", "pclk", "ptp_ref", "tx", "gtx";
>> +			resets = <&rstgen JH7100_RSTN_GMAC_AHB>;
>> +			reset-names = "ahb";
>> +			interrupts = <6>, <7>;
>> +			interrupt-names = "macirq", "eth_wake_irq";
>> +			max-frame-size = <9000>;
>> +			snps,multicast-filter-bins = <32>;
>> +			snps,perfect-filter-entries = <128>;
>> +			starfive,syscon = <&sysmain 0x70 0>;
>> +			rx-fifo-depth = <32768>;
>> +			tx-fifo-depth = <16384>;
>> +			snps,axi-config = <&stmmac_axi_setup>;
>> +			snps,fixed-burst;
>> +			snps,force_thresh_dma_mode;
>> +			status = "disabled";
>> +
>> +			stmmac_axi_setup: stmmac-axi-config {
>> +				snps,wr_osr_lmt = <0xf>;
>> +				snps,rd_osr_lmt = <0xf>;
> 
> As I also noted on the JH7110 patches these are not addresses or offsets but
> limits eg. counting things, which makes a lot more sense in decimal for most
> humans. But here you've changed them back to 0xf, why?

That's a left over from v1. Will fix, thanks!

>> +				snps,blen = <256 128 64 32 0 0 0>;
>> +			};
>> +		};
>> +
>>  		clkgen: clock-controller at 11800000 {
>>  			compatible = "starfive,jh7100-clkgen";
>>  			reg = <0x0 0x11800000 0x0 0x10000>;
>> @@ -193,6 +224,11 @@ rstgen: reset-controller at 11840000 {
>>  			#reset-cells = <1>;
>>  		};
>>
>> +		sysmain: syscon at 11850000 {
>> +			compatible = "starfive,jh7100-sysmain", "syscon";
>> +			reg = <0x0 0x11850000 0x0 0x10000>;
>> +		};
>> +
>>  		i2c0: i2c at 118b0000 {
>>  			compatible = "snps,designware-i2c";
>>  			reg = <0x0 0x118b0000 0x0 0x10000>;
>> --
>> 2.42.0
>>



More information about the linux-arm-kernel mailing list