[PATCH 5/8] arm64: dts: qcom: Add SDX75 platform and IDP board support

Konrad Dybcio konrad.dybcio at linaro.org
Tue May 30 10:49:05 PDT 2023



On 30.05.2023 13:40, Rohit Agarwal wrote:
> Thanks for reviewing. Sorry for the late reply was on leave.
> 
> On 5/19/2023 10:58 PM, Konrad Dybcio wrote:
>>
>> On 19.05.2023 11:09, Rohit Agarwal wrote:
>>> Add basic devicetree support for SDX75 platform and IDP board from
>>> Qualcomm. The SDX75 platform features an ARM Cortex A55 CPU which forms
>>> the Application Processor Sub System (APSS) along with standard Qualcomm
>>> peripherals like GCC, TLMM, UART, QPIC, and BAM etc... Also, there
>>> exists the networking parts such as IPA, MHI, PCIE-EP, EMAC, and Modem
>>> etc..
>>>
>>> This commit adds basic devicetree support.
>>>
>>> Signed-off-by: Rohit Agarwal <quic_rohiagar at quicinc.com>
>>> ---
>>>   arch/arm64/boot/dts/qcom/Makefile      |   1 +
>>>   arch/arm64/boot/dts/qcom/sdx75-idp.dts |  19 ++
>>>   arch/arm64/boot/dts/qcom/sdx75.dtsi    | 534 +++++++++++++++++++++++++++++++++
>>>   3 files changed, 554 insertions(+)
>>>   create mode 100644 arch/arm64/boot/dts/qcom/sdx75-idp.dts
>>>   create mode 100644 arch/arm64/boot/dts/qcom/sdx75.dtsi
>>>
>>> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
>>> index d42c595..4fd5a18 100644
>>> --- a/arch/arm64/boot/dts/qcom/Makefile
>>> +++ b/arch/arm64/boot/dts/qcom/Makefile
>>> @@ -173,6 +173,7 @@ dtb-$(CONFIG_ARCH_QCOM)    += sdm845-xiaomi-polaris.dtb
>>>   dtb-$(CONFIG_ARCH_QCOM)    += sdm845-shift-axolotl.dtb
>>>   dtb-$(CONFIG_ARCH_QCOM)    += sdm850-lenovo-yoga-c630.dtb
>>>   dtb-$(CONFIG_ARCH_QCOM)    += sdm850-samsung-w737.dtb
>>> +dtb-$(CONFIG_ARCH_QCOM)    += sdx75-idp.dtb
>>>   dtb-$(CONFIG_ARCH_QCOM)    += sm4250-oneplus-billie2.dtb
>>>   dtb-$(CONFIG_ARCH_QCOM)    += sm6115p-lenovo-j606f.dtb
>>>   dtb-$(CONFIG_ARCH_QCOM)    += sm6125-sony-xperia-seine-pdx201.dtb
>>> diff --git a/arch/arm64/boot/dts/qcom/sdx75-idp.dts b/arch/arm64/boot/dts/qcom/sdx75-idp.dts
>>> new file mode 100644
>>> index 0000000..e2e803b
>>> --- /dev/null
>>> +++ b/arch/arm64/boot/dts/qcom/sdx75-idp.dts
>>> @@ -0,0 +1,19 @@
>>> +// SPDX-License-Identifier: BSD-3-Clause
>>> +/*
>>> + * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
>>> + */
>>> +
>>> +/dts-v1/;
>>> +
>>> +#include "sdx75.dtsi"
>>> +
>>> +/ {
>>> +    model = "Qualcomm Technologies, Inc. SDX75 IDP";
>>> +    compatible = "qcom,sdx75-idp", "qcom,sdx75";
>>> +    qcom,board-id = <0x2010022 0x302>;
>> You should be able to get by without qcom,{msm,board}-id.
> Actually the bootloader requires the msm and board id. Shouldn't this become a necessary field then?
We generally discourage that, especially since at least on the LA front
it became unnecessary (no msm-id and appended dtb -> abl picks the only
one present).. I'm not sure at what point in product dev the SDX75 is,
but if we could get rid of that requirement, it'd be very nice..

OTOH getting rid of it just on one device and keeping it necessary with
fw builds that have been distributed to vendors sounds wouldn't be
very beneficial either :/ 


Konrad
>>
>>> +
>>> +};
>>> +
>>> +&tlmm {
>>> +    gpio-reserved-ranges = <110 6>;
>>> +};
>>> diff --git a/arch/arm64/boot/dts/qcom/sdx75.dtsi b/arch/arm64/boot/dts/qcom/sdx75.dtsi
>>> new file mode 100644
>>> index 0000000..c2b8810
>>> --- /dev/null
>>> +++ b/arch/arm64/boot/dts/qcom/sdx75.dtsi
>>> @@ -0,0 +1,534 @@
>>> +// SPDX-License-Identifier: BSD-3-Clause
>>> +/*
>>> + * SDX75 SoC device tree source
>>> + *
>>> + * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
>>> + *
>>> + */
>>> +
>>> +#include <dt-bindings/clock/qcom,rpmh.h>
>>> +#include <dt-bindings/interrupt-controller/arm-gic.h>
>>> +#include <dt-bindings/soc/qcom,rpmh-rsc.h>
>>> +
>>> +/ {
>>> +    #address-cells = <2>;
>>> +    #size-cells = <2>;
>>> +    qcom,msm-id = <556 0x10000>;
>>> +    interrupt-parent = <&intc>;
>>> +
>>> +    chosen: chosen { };
>>> +
>>> +    memory {
>> The memory node should have a unit address.
> Sure will update this.
>>
>>> +        device_type = "memory";
>>> +        reg = <0 0 0 0>;
>>> +    };
>>> +
>>> +    clocks { };
>>> +
>>> +    cpus {
>>> +        #address-cells = <2>;
>>> +        #size-cells = <0>;
>>> +
>> [...]
>>
>>> +
>>> +        CLUSTER_PD: power-domain-cpu-cluster0 {
>>> +            #power-domain-cells = <0>;
>>> +            domain-idle-states = <&CLUSTER_SLEEP_0 &CX_RET &CLUSTER_SLEEP_1>;
>> Is CLUSTER_SLEEP_1 deeper than CX retention?
> Yes
>>
>>> +        };
>>> +    };
>>> +
>>> +    firmware {
>>> +        scm: scm {
>>> +            compatible = "qcom,scm-sdx75", "qcom,scm";
>>> +        };
>>> +    };
>>> +
>>> +    pmu {
>>> +        compatible = "arm,armv8-pmuv3";
>>> +        interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
>>> +    };
>>> +
>>> +    reserved-memory {
>>> +        #address-cells = <2>;
>>> +        #size-cells = <2>;
>>> +        ranges;
>>> +
>>> +        gunyah_hyp_mem: memory at 80000000 {
>> reserved memory subnodes should have meaningful node names, e.g.
>>
>> hypervisor at 800...
> Will update this.
>>
>>> +            reg = <0x0 0x80000000 0x0 0x800000>;
>>> +            no-map;
>>> +        };
>>> +
>> [...]
>>
>>> +
>>> +    smem: qcom,smem {
>>> +        compatible = "qcom,smem";
>>> +        memory-region = <&smem_mem>;
>>> +        hwlocks = <&tcsr_mutex 3>;
>>> +    };
>>> +
>>> +    soc: soc {
>>> +        #address-cells = <2>;
>>> +        #size-cells = <2>;
>>> +        ranges;
>> Are the SoC buses limited to 32b addresses?
> No, Will fix this in the next.
>>
>>> +        compatible = "simple-bus";
>> Compatible should go first.
> Yes, Ok.
>>> +
>>> +        tcsr_mutex: hwlock at 1f40000 {
>>> +            compatible = "qcom,tcsr-mutex";
>>> +            reg = <0x0 0x01f40000 0x0 0x40000>;
>>> +            #hwlock-cells = <1>;
>>> +        };
>>> +
>>> +        pdc: interrupt-controller at b220000 {
>>> +            compatible = "qcom,sdx75-pdc", "qcom,pdc";
>>> +            reg = <0x0 0xb220000 0x0 0x30000>,
>>> +                  <0x0 0x174000f0 0x0 0x64>;
>>> +            qcom,pdc-ranges = <0 147 52>,
>>> +                      <52 266 32>,
>>> +                      <84 500 59>;
>>> +            #interrupt-cells = <2>;
>>> +            interrupt-parent = <&intc>;
>>> +            interrupt-controller;
>>> +        };
>>> +
>>> +        tlmm: pinctrl at f000000 {
>>> +            compatible = "qcom,sdx75-tlmm";
>>> +            reg = <0x0 0x0f000000 0x0 0x400000>;
>>> +            interrupts = <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>;
>>> +            gpio-controller;
>>> +            #gpio-cells = <2>;
>>> +            gpio-ranges = <&tlmm 0 0 133>;
>>> +            interrupt-controller;
>>> +            #interrupt-cells = <2>;
>>> +            wakeup-parent = <&pdc>;
>>> +        };
>>> +
>>> +        apps_smmu: iommu at 15000000 {
>>> +            compatible = "qcom,sdx75-smmu-500", "arm,mmu-500";
>>> +            reg = <0x0 0x15000000 0x0 0x40000>;
>>> +            #iommu-cells = <2>;
>>> +            #global-interrupts = <2>;
>>> +            interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
>>> +                     <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
>>> +                     <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
>>> +                     <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
>>> +                     <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>,
>>> +                     <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
>>> +                     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
>>> +                     <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>,
>>> +                     <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
>>> +                     <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
>>> +                     <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
>>> +                     <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
>>> +                     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
>>> +                     <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
>>> +                     <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
>>> +                     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
>>> +                     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
>>> +                     <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
>>> +                     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
>>> +                     <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
>>> +                     <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
>>> +                     <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
>>> +                     <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
>>> +                     <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
>>> +                     <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>,
>>> +                     <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>,
>>> +                     <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>,
>>> +                     <GIC_SPI 301 IRQ_TYPE_LEVEL_HIGH>,
>>> +                     <GIC_SPI 302 IRQ_TYPE_LEVEL_HIGH>,
>>> +                     <GIC_SPI 303 IRQ_TYPE_LEVEL_HIGH>,
>>> +                     <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>,
>>> +                     <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>,
>>> +                     <GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>;
>> Many newer SoCs have dma-coherent SMMUs. Is this the case here?
> Yes, Will add the dma-coherent property here.
>>
>>> +        };
>>> +
>>> +        intc: interrupt-controller at 17200000 {
>>> +            compatible = "arm,gic-v3";
>>> +            #interrupt-cells = <3>;
>>> +            interrupt-controller;
>>> +            #redistributor-regions = <1>;
>>> +            redistributor-stride = <0x0 0x20000>;
>>> +            reg = <0x0 0x17200000 0x0 0x10000>,
>>> +                  <0x0 0x17260000 0x0 0x80000>;
>>> +            interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
>>> +        };
>>> +
>>> +        timer at 17420000 {
>>> +            compatible = "arm,armv7-timer-mem";
>>> +            #address-cells = <2>;
>>> +            #size-cells = <2>;
>>> +            ranges;
>>> +            reg = <0x0 0x17420000 0x0 0x1000>;
>>> +            clock-frequency = <19200000>;
>> clock-frequency is discouraged, unless strictly necessary.
>>
>> Since gh is running, the timer is already programmed so it should be
>> fine to drop this.
>>
>> [...]
>>
>>> +    timer {
>>> +        compatible = "arm,armv8-timer";
>>> +        interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
>>> +                 <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
>>> +                 <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
>>> +                 <GIC_PPI 12 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
>>> +        clock-frequency = <19200000>;
>> Ditto
> Ok Thanks for the info. Dropping the clock frequency property in the next version.
> 
> Thanks,
> Rohit.
>>
>> Konrad
>>> +    };
>>> +};



More information about the linux-arm-kernel mailing list