[PATCH v1 3/5] arm64: dts: ti: add verdin am62

Francesco Dolcini francesco at dolcini.it
Tue May 30 03:18:28 PDT 2023


On Wed, May 24, 2023 at 04:36:29PM +0200, Francesco Dolcini wrote:
> From: Francesco Dolcini <francesco.dolcini at toradex.com>
> 
> This patch adds the device tree to support Toradex Verdin AM62 a
> computer on module which can be used on different carrier boards
> and the Toradex Verdin Development Board carrier board.
> 
> The module consists of an TI AM62 family SoC (either AM623 or AM625), a
> TPS65219 PMIC, a Gigabit Ethernet PHY, 512MB to 2GB of LPDDR4 RAM, an
> eMMC, a TLA2024 ADC, an I2C EEPROM, an RX8130 RTC, and optional Parallel
> RGB to MIPI DSI bridge plus an optional Bluetooth/Wi-Fi module.
> 
> Anything that is not self-contained on the module is disabled by
> default.
> 
> So far there is no display nor USB role switch supported, apart of that
> all the other functionalities are fine.
> 
> Link: https://developer.toradex.com/hardware/verdin-som-family/modules/verdin-am62/
> Link: https://www.toradex.com/computer-on-modules/verdin-arm-family/ti-am62
> Link: https://www.toradex.com/products/carrier-board/verdin-development-board-kit
> Signed-off-by: Francesco Dolcini <francesco.dolcini at toradex.com>
> ---
>  arch/arm64/boot/dts/ti/Makefile               |    2 +
>  .../arm64/boot/dts/ti/k3-am62-verdin-dev.dtsi |  233 +++
>  .../boot/dts/ti/k3-am62-verdin-nonwifi.dtsi   |   16 +
>  .../boot/dts/ti/k3-am62-verdin-wifi.dtsi      |   36 +
>  arch/arm64/boot/dts/ti/k3-am62-verdin.dtsi    | 1400 +++++++++++++++++
>  .../dts/ti/k3-am625-verdin-nonwifi-dev.dts    |   19 +
>  .../boot/dts/ti/k3-am625-verdin-wifi-dev.dts  |   19 +
>  7 files changed, 1725 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/ti/k3-am62-verdin-dev.dtsi
>  create mode 100644 arch/arm64/boot/dts/ti/k3-am62-verdin-nonwifi.dtsi
>  create mode 100644 arch/arm64/boot/dts/ti/k3-am62-verdin-wifi.dtsi
>  create mode 100644 arch/arm64/boot/dts/ti/k3-am62-verdin.dtsi
>  create mode 100644 arch/arm64/boot/dts/ti/k3-am625-verdin-nonwifi-dev.dts
>  create mode 100644 arch/arm64/boot/dts/ti/k3-am625-verdin-wifi-dev.dts
> 

<snip>

> +/* Verdin UART_1, connector X50 through RS485 transceiver. */
> +&main_uart1 {
> +	linux,rs485-enabled-at-boot-time;
> +	/*
> +	 * The 8250 OMAP driver interprets rs485-rts-active-high and its
> +	 * ioctl equivalent as driving RTS low on send.
> +	 */
> +	rs485-rts-active-high;

After some additional investigation this (rs485-rts-active-high) can be
removed, I'll send a v2 before the end of the week with just this change
unless I get some more feedback in the meantime.

Francesco



More information about the linux-arm-kernel mailing list