[PATCH V2] arm64: dts: marvell: add DTS for GL.iNet GL-MV1000
Pali Rohár
pali at kernel.org
Wed Mar 29 12:39:02 PDT 2023
PING?
On Friday 03 February 2023 18:46:18 Pali Rohár wrote:
> On Thursday 02 February 2023 10:37:06 Enrico Mioso wrote:
> > The GL-MV1000 (Brume) is a small form-factor gateway router.
> > It is based on the Marvell Armada 88F3720 SOC (1GHz), has 3 gigabit ethernet ports, 1 GB RAM, 16M SPI flash, 8GB eMMC and an uSD slot, as well as an USB 2.0 type A and an USB 3.0 type C port.
> >
> > Signed-off-by: Enrico Mioso <mrkiko.rs at gmail.com>
> > CC: Pali <pali at kernel.org>
>
> Looks good,
>
> Reviewed-by: Pali Rohár <pali at kernel.org>
>
> > ---
> > arch/arm64/boot/dts/marvell/Makefile | 1 +
> > .../dts/marvell/armada-3720-gl-mv1000.dts | 239 ++++++++++++++++++
> > 2 files changed, 240 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts
> >
> > diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
> > index 058237681fe5..79ac09b58a89 100644
> > --- a/arch/arm64/boot/dts/marvell/Makefile
> > +++ b/arch/arm64/boot/dts/marvell/Makefile
> > @@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-emmc.dtb
> > dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-ultra.dtb
> > dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-v7.dtb
> > dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-v7-emmc.dtb
> > +dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-gl-mv1000.dtb
> > dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-turris-mox.dtb
> > dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-uDPU.dtb
> > dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-db.dtb
> > diff --git a/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts b/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts
> > new file mode 100644
> > index 000000000000..b1b45b4fa9d4
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts
> > @@ -0,0 +1,239 @@
> > +// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
> > +
> > +/dts-v1/;
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/input/input.h>
> > +#include "armada-372x.dtsi"
> > +
> > +/ {
> > + model = "GL.iNet GL-MV1000";
> > + compatible = "glinet,gl-mv1000", "marvell,armada3720";
> > +
> > + aliases {
> > + led-boot = &led_power;
> > + led-failsafe = &led_power;
> > + led-running = &led_power;
> > + led-upgrade = &led_power;
> > + };
> > +
> > + chosen {
> > + stdout-path = "serial0:115200n8";
> > + };
> > +
> > + memory at 0 {
> > + device_type = "memory";
> > + reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
> > + };
> > +
> > + vcc_sd_reg1: regulator {
> > + compatible = "regulator-gpio";
> > + regulator-name = "vcc_sd1";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-boot-on;
> > +
> > + gpios-states = <0>;
> > + states = <1800000 0x1
> > + 3300000 0x0>;
> > + enable-active-high;
> > + };
> > +
> > + keys {
> > + compatible = "gpio-keys";
> > +
> > + reset {
> > + label = "reset";
> > + linux,code = <KEY_RESTART>;
> > + gpios = <&gpionb 14 GPIO_ACTIVE_LOW>;
> > + };
> > +
> > + switch {
> > + label = "switch";
> > + linux,code = <BTN_0>;
> > + gpios = <&gpiosb 22 GPIO_ACTIVE_LOW>;
> > + };
> > + };
> > +
> > + leds {
> > + compatible = "gpio-leds";
> > +
> > + vpn {
> > + label = "green:vpn";
> > + gpios = <&gpionb 11 GPIO_ACTIVE_LOW>;
> > + };
> > +
> > + wan {
> > + label = "green:wan";
> > + gpios = <&gpionb 12 GPIO_ACTIVE_LOW>;
> > + };
> > +
> > + led_power: power {
> > + label = "green:power";
> > + gpios = <&gpionb 13 GPIO_ACTIVE_LOW>;
> > + default-state = "on";
> > + };
> > + };
> > +};
> > +
> > +&spi0 {
> > + status = "okay";
> > +
> > + flash at 0 {
> > + reg = <0>;
> > + compatible = "jedec,spi-nor";
> > + spi-max-frequency = <104000000>;
> > + m25p,fast-read;
> > + partitions {
> > + compatible = "fixed-partitions";
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > +
> > + partition at 0 {
> > + label = "firmware";
> > + reg = <0 0xf0000>;
> > + };
> > +
> > + partition at f0000 {
> > + label = "u-boot-env";
> > + reg = <0xf0000 0x8000>;
> > + };
> > +
> > + factory: partition at f8000 {
> > + label = "factory";
> > + reg = <0xf8000 0x8000>;
> > + read-only;
> > + };
> > +
> > + partition at 100000 {
> > + label = "dtb";
> > + reg = <0x100000 0x10000>;
> > + read-only;
> > + };
> > +
> > + partition at 110000 {
> > + label = "rescue";
> > + reg = <0x110000 0x1000000>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&sdhci1 {
> > + wp-inverted;
> > + bus-width = <4>;
> > + cd-gpios = <&gpionb 17 GPIO_ACTIVE_LOW>;
> > + marvell,pad-type = "sd";
> > + no-1-8-v;
> > + vqmmc-supply = <&vcc_sd_reg1>;
> > + status = "okay";
> > +};
> > +
> > +&sdhci0 {
> > + bus-width = <8>;
> > + mmc-ddr-1_8v;
> > + mmc-hs400-1_8v;
> > + non-removable;
> > + no-sd;
> > + no-sdio;
> > + marvell,pad-type = "fixed-1-8v";
> > + status = "okay";
> > +};
> > +
> > +&usb3 {
> > + status = "okay";
> > +};
> > +
> > +&usb2 {
> > + status = "okay";
> > +};
> > +
> > +&uart0 {
> > + status = "okay";
> > +};
> > +
> > +&mdio {
> > + switch0: switch0 at 1 {
> > + compatible = "marvell,mv88e6085";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <1>;
> > +
> > + dsa,member = <0 0>;
> > +
> > + ports: ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port at 0 {
> > + reg = <0>;
> > + label = "cpu";
> > + ethernet = <ð0>;
> > + };
> > +
> > + port at 1 {
> > + reg = <1>;
> > + label = "wan";
> > + phy-handle = <&switch0phy0>;
> > + };
> > +
> > + port at 2 {
> > + reg = <2>;
> > + label = "lan0";
> > + phy-handle = <&switch0phy1>;
> > +
> > + nvmem-cells = <&macaddr_factory_6>;
> > + nvmem-cell-names = "mac-address";
> > + };
> > +
> > + port at 3 {
> > + reg = <3>;
> > + label = "lan1";
> > + phy-handle = <&switch0phy2>;
> > +
> > + nvmem-cells = <&macaddr_factory_6>;
> > + nvmem-cell-names = "mac-address";
> > + };
> > + };
> > +
> > + mdio {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + switch0phy0: switch0phy0 at 11 {
> > + reg = <0x11>;
> > + };
> > + switch0phy1: switch0phy1 at 12 {
> > + reg = <0x12>;
> > + };
> > + switch0phy2: switch0phy2 at 13 {
> > + reg = <0x13>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +ð0 {
> > + nvmem-cells = <&macaddr_factory_0>;
> > + nvmem-cell-names = "mac-address";
> > + phy-mode = "rgmii-id";
> > + status = "okay";
> > +
> > + fixed-link {
> > + speed = <1000>;
> > + full-duplex;
> > + };
> > +};
> > +
> > +&factory {
> > + compatible = "nvmem-cells";
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > +
> > + macaddr_factory_0: macaddr at 0 {
> > + reg = <0x0 0x6>;
> > + };
> > +
> > + macaddr_factory_6: macaddr at 6 {
> > + reg = <0x6 0x6>;
> > + };
> > +};
> > --
> > 2.39.1
> >
More information about the linux-arm-kernel
mailing list