[PATCH 3/6] arm64: dts: ti: k3-am68-sk-base-board: Add uart pinmux

[Kumar, Udit]

Hi Nishanth,

On 6/2/2023 9:05 PM, Nishanth Menon wrote:
> Define the wakeup uart pin-mux for completeness and add explicit
> muxing for mcu_uart0. This allows the device tree usage in bootloader
> and firmwares that can configure the same appropriately.
>
> Signed-off-by: Nishanth Menon <nm at ti.com>
> ---
> New patch in the series
>
>   .../boot/dts/ti/k3-am68-sk-base-board.dts     | 26 +++++++++++++++++++
>   1 file changed, 26 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts b/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
> index 014ff13d1032..979898bc5b02 100644
> --- a/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
> @@ -22,6 +22,8 @@ chosen {
>   	};
>   
>   	aliases {
> +		serial0 = &wkup_uart0;
> +		serial1 = &mcu_uart0;
>   		serial2 = &main_uart8;
>   		mmc1 = &main_sdhci1;
>   		can0 = &mcu_mcan0;
> @@ -202,6 +204,15 @@ J721S2_IOPAD(0x08c, PIN_INPUT, 7) /* (T25) MCASP0_AXR7.GPIO0_35 */
>   };
>   
>   &wkup_pmx2 {
> +	wkup_uart0_pins_default: wkup-uart0-pins-default {
> +		pinctrl-single,pins = <
> +			J721S2_WKUP_IOPAD(0x070, PIN_INPUT, 0) /* (E25) WKUP_GPIO0_6.WKUP_UART0_CTSn */
> +			J721S2_WKUP_IOPAD(0x074, PIN_OUTPUT, 0) /* (F28) WKUP_GPIO0_7.WKUP_UART0_RTSn */
> +			J721S2_WKUP_IOPAD(0x048, PIN_INPUT, 0) /* (D28) WKUP_UART0_RXD */
> +			J721S2_WKUP_IOPAD(0x04c, PIN_OUTPUT, 0) /* (D27) WKUP_UART0_TXD */
> +		>;
> +	};
> +
>   	mcu_cpsw_pins_default: mcu-cpsw-pins-default {
>   		pinctrl-single,pins = <
>   			J721S2_WKUP_IOPAD(0x02C, PIN_INPUT, 0) /* (B22) MCU_RGMII1_RD0 */
> @@ -254,6 +265,13 @@ J721S2_WKUP_IOPAD(0x07c, PIN_INPUT, 0) /* (H26) WKUP_GPIO0_9.MCU_I2C1_SDA */
>   		>;
>   	};
>   
> +	mcu_uart0_pins_default: mcu-uart0-pins-default {
> +		pinctrl-single,pins = <
> +			J721S2_WKUP_IOPAD(0x08c, PIN_INPUT, 0) /* (C24) WKUP_GPIO0_13.MCU_UART0_RXD */
> +			J721S2_WKUP_IOPAD(0x088, PIN_OUTPUT, 0) /* (C25) WKUP_GPIO0_12.MCU_UART0_TXD */
> +		>;
> +	};

Series look good.

One small question, We don't have CTS and RTS Pin for mcu uart ,

is this due to board connections ?


> [..]