[PATCH] arm64: dts: ti: k3-am69-sk: Enable MCU CPSW2G

[Nishanth Menon]

On 23:12-20230605, sabiya.d at mistralsolutions.com wrote:
> From: Dasnavis Sabiya <sabiya.d at ti.com>
> 
> Add device tree support to enable MCU CPSW for AM69 SK
> 
> Signed-off-by: Dasnavis Sabiya <sabiya.d at ti.com>

Does'nt
https://lore.kernel.org/linux-arm-kernel/20230602214937.2349545-6-nm@ti.com/
address this?

I already CCed you, so do you care to ack instead? OR provide review
comments so that I can improve the patch?

> ---
>  arch/arm64/boot/dts/ti/k3-am69-sk.dts | 50 +++++++++++++++++++++++++++
>  1 file changed, 50 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am69-sk.dts b/arch/arm64/boot/dts/ti/k3-am69-sk.dts
> index bc49ba534790..4b7d9280d76f 100644
> --- a/arch/arm64/boot/dts/ti/k3-am69-sk.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am69-sk.dts
> @@ -104,6 +104,32 @@ vdd_sd_dv: regulator-tlv71033 {
>  	};
>  };
>  
> +&wkup_pmx0 {
> +	mcu_cpsw_pins_default: mcu-cpsw-pins-default {
> +		pinctrl-single,pins = <
> +			J784S4_WKUP_IOPAD(0x094, PIN_INPUT, 0) /* (A35) MCU_RGMII1_RD0 */
> +			J784S4_WKUP_IOPAD(0x090, PIN_INPUT, 0) /* (B36) MCU_RGMII1_RD1 */
> +			J784S4_WKUP_IOPAD(0x08c, PIN_INPUT, 0) /* (C36) MCU_RGMII1_RD2 */
> +			J784S4_WKUP_IOPAD(0x088, PIN_INPUT, 0) /* (D36) MCU_RGMII1_RD3 */
> +			J784S4_WKUP_IOPAD(0x084, PIN_INPUT, 0) /* (B37) MCU_RGMII1_RXC */
> +			J784S4_WKUP_IOPAD(0x06c, PIN_INPUT, 0) /* (C37) MCU_RGMII1_RX_CTL */
> +			J784S4_WKUP_IOPAD(0x07c, PIN_OUTPUT, 0) /* (D37) MCU_RGMII1_TD0 */
> +			J784S4_WKUP_IOPAD(0x078, PIN_OUTPUT, 0) /* (D38) MCU_RGMII1_TD1 */
> +			J784S4_WKUP_IOPAD(0x074, PIN_OUTPUT, 0) /* (E37) MCU_RGMII1_TD2 */
> +			J784S4_WKUP_IOPAD(0x070, PIN_OUTPUT, 0) /* (E38) MCU_RGMII1_TD3 */
> +			J784S4_WKUP_IOPAD(0x080, PIN_OUTPUT, 0) /* (E36) MCU_RGMII1_TXC */
> +			J784S4_WKUP_IOPAD(0x068, PIN_OUTPUT, 0) /* (C38) MCU_RGMII1_TX_CTL */
> +		>;
> +	};
> +
> +	mcu_mdio_pins_default: mcu-mdio-pins-default {
> +		pinctrl-single,pins = <
> +			J784S4_WKUP_IOPAD(0x09c, PIN_OUTPUT, 0) /* (A36) MCU_MDIO0_MDC */
> +			J784S4_WKUP_IOPAD(0x098, PIN_INPUT, 0) /* (B35) MCU_MDIO0_MDIO */
> +		>;
> +	};
> +};
> +
>  &main_pmx0 {
>  	main_uart8_pins_default: main-uart8-pins-default {
>  		pinctrl-single,pins = <
> @@ -178,3 +204,27 @@ &main_sdhci1 {
>  &main_gpio0 {
>  	status = "okay";
>  };
> +
> +&mcu_cpsw {
> +	status = "okay";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&mcu_cpsw_pins_default>;
> +};
> +
> +&davinci_mdio {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&mcu_mdio_pins_default>;
> +
> +	mcu_phy0: ethernet-phy at 0 {
> +		reg = <0>;
> +		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
> +		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
> +		ti,min-output-impedance;
> +	};
> +};
> +
> +&mcu_cpsw_port1 {
> +	status = "okay";
> +	phy-mode = "rgmii-rxid";
> +	phy-handle = <&mcu_phy0>;
> +};
> -- 
> 2.25.1
> 

-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D