[PATCH 09/10] arm64: dts: imx8ulp-evk: add 100MHz/200MHz pinctrl setting for eMMC

[Shawn Guo]

On Mon, Jul 24, 2023 at 06:51:17AM +0000, Bough Chen wrote:
> > -----Original Message-----
> > From: Shawn Guo <shawnguo at kernel.org>
> > Sent: 2023年7月18日 11:32
> > To: Peng Fan (OSS) <peng.fan at oss.nxp.com>
> > Cc: robh+dt at kernel.org; krzysztof.kozlowski+dt at linaro.org;
> > s.hauer at pengutronix.de; kernel at pengutronix.de; festevam at gmail.com;
> > dl-linux-imx <linux-imx at nxp.com>; devicetree at vger.kernel.org;
> > linux-arm-kernel at lists.infradead.org; linux-kernel at vger.kernel.org; Bough
> > Chen <haibo.chen at nxp.com>; Sherry Sun <sherry.sun at nxp.com>; Peng Fan
> > <peng.fan at nxp.com>
> > Subject: Re: [PATCH 09/10] arm64: dts: imx8ulp-evk: add 100MHz/200MHz
> > pinctrl setting for eMMC
> > 
> > On Sun, Jun 25, 2023 at 08:42:37PM +0800, Peng Fan (OSS) wrote:
> > > From: Haibo Chen <haibo.chen at nxp.com>
> > >
> > > Add 100MHz and 200MHz pinctrl setting for eMMC, and enable 8 bit bus
> > > mode to config the eMMC work at HS400ES mode.
> > >
> > > Also update to use Standard Drive Strength for USDHC pad to get a
> > > better signal quality per Hardware team suggests.
> > >
> > > Reviewed-by: Sherry Sun <sherry.sun at nxp.com>
> > > Signed-off-by: Haibo Chen <haibo.chen at nxp.com>
> > > Signed-off-by: Peng Fan <peng.fan at nxp.com>
> > > ---
> > >  arch/arm64/boot/dts/freescale/imx8ulp-evk.dts | 26
> > > ++++++++++---------
> > >  1 file changed, 14 insertions(+), 12 deletions(-)
> > >
> > > diff --git a/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts
> > > b/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts
> > > index e459dc35e469..ab7af705bbca 100644
> > > --- a/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts
> > > +++ b/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts
> > > @@ -121,9 +121,11 @@ &lpuart5 {
> > >  };
> > >
> > >  &usdhc0 {
> > > -	pinctrl-names = "default", "sleep";
> > > +	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
> > >  	pinctrl-0 = <&pinctrl_usdhc0>;
> > >  	pinctrl-1 = <&pinctrl_usdhc0>;
> > > +	pinctrl-2 = <&pinctrl_usdhc0>;
> > > +	pinctrl-3 = <&pinctrl_usdhc0>;
> > 
> > All three speed modes use the same pinctrl?
> 
> Yes, the IOMUX on imx8ulp do not support config different drive strength. So here use the same pinctrl.

Mention that in the commit log or with a comment would be helpful.

Shawn