[PATCH v3 50/50] ARM: dts: at91: sam9x75_curiosity: add sam9x75 curiosity board
Krzysztof Kozlowski
krzysztof.kozlowski at linaro.org
Fri Jul 28 04:58:40 PDT 2023
On 28/07/2023 12:31, Varshini Rajendran wrote:
> Add device tree file for sam9x75 curiosity board.
>
> Signed-off-by: Varshini Rajendran <varshini.rajendran at microchip.com>
> ---
> arch/arm/boot/dts/microchip/Makefile | 5 +
> .../dts/microchip/at91-sam9x75_curiosity.dts | 311 ++++++++++++++++++
> 2 files changed, 316 insertions(+)
> create mode 100644 arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dts
>
> diff --git a/arch/arm/boot/dts/microchip/Makefile b/arch/arm/boot/dts/microchip/Makefile
> index 0f5193d05a31..f3d604c30325 100644
> --- a/arch/arm/boot/dts/microchip/Makefile
> +++ b/arch/arm/boot/dts/microchip/Makefile
> @@ -10,6 +10,7 @@ DTC_FLAGS_at91-sama5d3_eds := -@
> DTC_FLAGS_at91-sama5d3_xplained := -@
> DTC_FLAGS_at91-sama5d4_xplained := -@
> DTC_FLAGS_at91-sama7g5ek := -@
> +DTC_FLAGS_at91-sam9x75_curiosity := -@
> dtb-$(CONFIG_SOC_AT91RM9200) += \
> at91rm9200ek.dtb \
> mpa1600.dtb
> @@ -61,6 +62,10 @@ dtb-$(CONFIG_SOC_SAM9X60) += \
> at91-sam9x60_curiosity.dtb \
> at91-sam9x60ek.dtb
> # Enables support for device-tree overlays
> +DTC_FLAGS_at91-sam9x75_curiosity := -@
> +dtb-$(CONFIG_SOC_SAM9X7) += \
> + at91-sam9x75_curiosity.dtb
> +# Enables support for device-tree overlays
> DTC_FLAGS_at91-sama5d27_som1_ek := -@
> DTC_FLAGS_at91-sama5d27_wlsom1_ek := -@
> DTC_FLAGS_at91-sama5d2_icp := -@
> diff --git a/arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dts b/arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dts
> new file mode 100644
> index 000000000000..a9ecb02a9f3c
> --- /dev/null
> +++ b/arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dts
> @@ -0,0 +1,311 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * at91-sam9x75_curiosity.dts - Device Tree file for Microchip SAM9X75 Curiosity board
> + *
> + * Copyright (C) 2023 Microchip Technology Inc. and its subsidiaries
> + *
> + * Author: Varshini Rajendran <varshini.rajendran at microchip.com>
> + */
> +/dts-v1/;
> +#include "sam9x7.dtsi"
> +#include <dt-bindings/input/input.h>
> +
> +/ {
> + model = "Microchip SAM9X75 Curiosity";
> + compatible = "microchip,sam9x75-curiosity", "microchip,sam9x7", "atmel,at91sam9";
> +
> + aliases {
> + i2c0 = &i2c6;
> + i2c1 = &i2c7;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + clocks {
> + clock-slowxtal {
You should override/extend nodes by label/phandle. Doing by full node
path is error prone and make it more difficult to make changes to DTSI
later.
> + clock-frequency = <32768>;
> + };
> +
> + clock-mainxtal {
> + clock-frequency = <24000000>;
> + };
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_key_gpio_default>;
> +
> + button-user {
> + label = "USER";
> + gpios = <&pioC 9 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_PROG1>;
> + wakeup-source;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_led_gpio_default>;
> +
> + led-0 {
> + label = "red";
Use function and color instead.
> + gpios = <&pioC 19 GPIO_ACTIVE_HIGH>;
> + };
> +
> + led-1 {
> + label = "green";
Use function and color instead.
> + gpios = <&pioC 21 GPIO_ACTIVE_HIGH>;
> + };
> +
> + led-2 {
> + label = "blue";
Use function and color instead.
> + gpios = <&pioC 20 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +
> + memory at 20000000 {
> + device_type = "memory";
> + reg = <0x20000000 0x10000000>;
> + };
> +};
> +
> +&dbgu {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_dbgu>;
> + status = "okay";
> +};
> +
> +&dma0 {
> + status = "okay";
> +};
> +
> +&ehci0 {
> + status = "okay";
> +};
> +
> +&flx6 {
> + atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
> + status = "okay";
> +
> + i2c6 {
This is just broken. Not tested, either.
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flx6_default>;
> + i2c-analog-filter;
> + i2c-digital-filter;
> + i2c-digital-filter-width-ns = <35>;
> + status = "okay";
> +
Best regards,
Krzysztof
More information about the linux-arm-kernel
mailing list