[PATCH v2 4/4] arm64: dts: freescale: Add DEBIX SOM A and SOM A I/O Board support

Laurent Pinchart laurent.pinchart at ideasonboard.com
Tue Jul 25 06:26:07 PDT 2023


Hi Marco,

Thank you for the patch.

On Mon, Jul 17, 2023 at 06:51:27PM +0200, Marco Felsch wrote:
> Add support for the Debix SOM A + SOM A I/O board. The commit enables
> only the basic features like:
>  - 2x UART
>  - 2x Network
>  - eMMC/µSD
>  - CAN
>  - QSPI
>  - USB Host / Device
> 
> Signed-off-by: Marco Felsch <m.felsch at pengutronix.de>
> ---
> Required patchsets:
> 
> - usb: https://lore.kernel.org/all/20230623142228.4069084-1-m.felsch@pengutronix.de/
> - net: https://lore.kernel.org/all/20230717164307.2868264-1-m.felsch@pengutronix.de/
> 
> Changelog:
> 
> v2:
> - drop to generic polyhex,imx8mp-debix binding
> - net/phy: replace deprecated snps,reset-* and phy-reset-* bindings with
>   new phy-node based ones
> - net/phy: fix phy properties and reset timings
> - net/phy: add fec phy-supply handling
> - net/phy: add eqos phy-supply handling
> - net/phy: fix baseboard-vdd3v3 timings to fulfill net-phy-timings
> - Fix spelling
> - Drop superfluous blank lines
> - pmic: make use of IRQ_TYPE_LEVEL_LOW
> - pmic: add whitespace between buck node name and '{'
> 
>  arch/arm64/boot/dts/freescale/Makefile        |   1 +
>  .../freescale/imx8mp-debix-som-a-bmb-08.dts   | 470 ++++++++++++++++++
>  .../dts/freescale/imx8mp-debix-som-a.dtsi     | 266 ++++++++++
>  3 files changed, 737 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-debix-som-a-bmb-08.dts
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-debix-som-a.dtsi
> 
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index ef7d17aef58f0..ca7c9595e6ffa 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -91,6 +91,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mn-venice-gw7902.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mp-beacon-kit.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mp-data-modul-edm-sbc.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mp-debix-model-a.dtb
> +dtb-$(CONFIG_ARCH_MXC) += imx8mp-debix-som-a-bmb-08.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mp-dhcom-pdk2.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mp-dhcom-pdk3.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb
> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a-bmb-08.dts b/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a-bmb-08.dts
> new file mode 100644
> index 0000000000000..17028ab169717
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a-bmb-08.dts
> @@ -0,0 +1,470 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2019 NXP
> + * Copyright (C) 2023 Pengutronix, Marco Felsch <kernel at pengutronix.de>
> + */
> +
> +/dts-v1/;
> +
> +#include "imx8mp-debix-som-a.dtsi"
> +
> +/ {
> +	model = "Polyhex i.MX8MPlus Debix SOM A on BMB-08";
> +	compatible = "polyhex,imx8mp-debix-som-a-bmb-08", "polyhex,imx8mp-debix-som-a",
> +		     "fsl,imx8mp";
> +
> +	chosen {
> +		stdout-path = &uart2;
> +	};
> +
> +	reg_baseboard_vdd3v3: regulator-baseboard-vdd3v3 {
> +		compatible = "regulator-fixed";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-name = "BB_VDD3V3";
> +		gpio = <&expander0 10 GPIO_ACTIVE_HIGH>;
> +		/* Required timings for ethernet phy's */
> +		startup-delay-us = <50000>;

The regulator's datasheet shows a much smaller delay (about 1500µs with
a 3A load).

> +		off-on-delay-us = <110000>;

Is this really a property of the regulator ? Or a requirement of the
ethernet PHY ? In the latter case, shouldn't it be handled by the PHY ?

> +		enable-active-high;
> +		regulator-always-on;

Why always on ? Same for the other supplies.

> +	};
> +
> +	reg_baseboard_vdd5v0: regulator-baseboard-vdd5v0 {
> +		compatible = "regulator-fixed";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-name = "BB_VDD5V";
> +		gpio = <&expander0 9 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
> +
> +	regulator-som-vdd1v8 {
> +		compatible = "regulator-fixed";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +		regulator-name = "SOM_VDD1V8_SW";
> +		gpio = <&expander0 12 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +		regulator-always-on;
> +	};
> +
> +	regulator-som-vdd3v3 {
> +		compatible = "regulator-fixed";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-name = "SOM_VDD3V3_SW";
> +		gpio = <&expander0 11 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +		regulator-always-on;
> +	};
> +
> +	reg_usdhc2_vmmc: regulator-usdhc2 {
> +		compatible = "regulator-fixed";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
> +		regulator-name = "VSD_3V3";

This seems to be produced by the SoM, it should be moved to the SoM
.dtsi.

> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
> +
> +	regulator-vbus-usb20 {
> +		compatible = "regulator-fixed";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-name = "USB20_5V";
> +		gpio = <&expander1 14 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +		regulator-always-on;
> +		vin-supply = <&reg_baseboard_vdd5v0>;
> +	};
> +
> +	regulator-vbus-usb30 {
> +		compatible = "regulator-fixed";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-name = "USB30_5V";
> +		gpio = <&expander1 12 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +		regulator-always-on;
> +		vin-supply = <&reg_baseboard_vdd5v0>;
> +	};
> +
> +	reg_vdd5v0: regulator-vdd5v0 {
> +		compatible = "regulator-fixed";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-name = "VDD_5V";
> +		gpio = <&expander0 8 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
> +};
> +
> +&eqos {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_eqos>;
> +	phy-supply = <&reg_baseboard_vdd3v3>;
> +	phy-handle = <&ethphy0>;
> +	phy-mode = "rgmii-id";
> +	status = "okay";
> +
> +	mdio {
> +		compatible = "snps,dwmac-mdio";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		ethphy0: ethernet-phy at 0 {

Unless I'm mistaken, the PHYs are both at address 1. Address 0 works as
it's the broadcast address, but is there a good reason not to use the
real address ? Same below.

> +			compatible = "ethernet-phy-ieee802.3-c22";
> +			reg = <0>;
> +			reset-gpios = <&gpio4 18 GPIO_ACTIVE_LOW>;
> +			reset-assert-us = <20000>;
> +			reset-deassert-us = <150000>;
> +			eee-broken-1000t;
> +			realtek,clkout-disable;
> +		};
> +	};
> +};
> +
> +&fec {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_fec>;
> +	phy-supply = <&reg_baseboard_vdd3v3>;
> +	phy-handle = <&ethphy1>;
> +	phy-mode = "rgmii-id";
> +	fsl,magic-packet;
> +	status = "okay";
> +
> +	mdio {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		ethphy1: ethernet-phy at 0 {
> +			compatible = "ethernet-phy-ieee802.3-c22";
> +			reg = <0>;
> +			reset-gpios = <&gpio4 19 GPIO_ACTIVE_LOW>;
> +			reset-assert-us = <20000>;
> +			reset-deassert-us = <150000>;
> +			eee-broken-1000t;
> +			realtek,clkout-disable;
> +		};
> +	};
> +};
> +
> +&flexcan1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_flexcan1>;
> +	xceiver-supply = <&reg_vdd5v0>;
> +	status = "okay";
> +};
> +
> +&flexcan2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_flexcan2>;
> +	xceiver-supply = <&reg_vdd5v0>;
> +	status = "okay";
> +};
> +
> +&flexspi {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_flexspi0>;
> +	status = "okay";
> +
> +	flash: flash at 0 {
> +		compatible = "jedec,spi-nor";
> +		reg = <0>;
> +		spi-max-frequency = <80000000>;
> +		spi-tx-bus-width = <1>;
> +		spi-rx-bus-width = <4>;
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +	};
> +};
> +
> +&i2c4 {
> +	expander0: gpio at 20 {
> +		compatible = "nxp,pca9535";
> +		reg = <0x20>;
> +		gpio-controller;
> +		#gpio-cells = <0x02>;
> +	};
> +
> +	expander1: gpio at 23 {
> +		compatible = "nxp,pca9535";
> +		reg = <0x23>;
> +		gpio-controller;
> +		#gpio-cells = <0x02>;
> +
> +		/*
> +		 * Since USB1 is bound to peripheral mode we need to ensure
> +		 * that VBUS is turned off.
> +		 */
> +		usb30-otg-hog {
> +			gpio-hog;
> +			gpios = <13 GPIO_ACTIVE_HIGH>;
> +			output-low;
> +			line-name = "USB30_OTG_EN";
> +		};
> +	};
> +
> +	eeprom at 52 {
> +		compatible = "atmel,24c02";
> +		reg = <0x52>;
> +		pagesize = <16>;
> +	};
> +
> +	rtc at 51 {
> +		compatible = "haoyu,hym8563";
> +		reg = <0x51>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_rtc>;
> +		interrupt-parent = <&gpio4>;
> +		interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
> +		#clock-cells = <0>;
> +	};
> +};
> +
> +&snvs_pwrkey {
> +	status = "okay";
> +};
> +
> +/* Debug */
> +&uart2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart2>;
> +	status = "okay";
> +};
> +
> +&uart3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart3>;
> +	status = "okay";
> +};
> +
> +&uart4 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart4>;
> +	status = "okay";
> +};
> +
> +&usb3_0 {
> +	status = "okay";
> +};
> +
> +&usb3_1 {
> +	status = "okay";
> +};
> +
> +&usb_dwc3_0 {
> +	dr_mode = "peripheral";
> +	status = "okay";
> +};
> +
> +&usb_dwc3_1 {
> +	dr_mode = "host";
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	status = "okay";
> +
> +	/* 2.x hub on port 1 */
> +	usb_hub_2_x: hub at 1 {
> +		compatible = "usb5e3,610";
> +		reg = <1>;
> +		reset-gpios = <&expander1 9 GPIO_ACTIVE_LOW>;
> +		vdd-supply = <&reg_vdd5v0>;
> +		peer-hub = <&usb_hub_3_x>;
> +	};
> +
> +	/* 3.x hub on port 2 */
> +	usb_hub_3_x: hub at 2 {
> +		compatible = "usb5e3,620";
> +		reg = <2>;
> +		reset-gpios = <&expander1 9 GPIO_ACTIVE_LOW>;
> +		vdd-supply = <&reg_vdd5v0>;
> +		peer-hub = <&usb_hub_2_x>;
> +	};
> +};
> +
> +&usb3_phy0 {
> +	status = "okay";
> +};
> +
> +&usb3_phy1 {
> +	status = "okay";
> +};
> +
> +/* µSD Card */
> +&usdhc2 {
> +	pinctrl-names = "default", "state_100mhz", "state_200mhz";
> +	pinctrl-0 = <&pinctrl_usdhc2>;
> +	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
> +	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
> +	assigned-clocks = <&clk IMX8MP_CLK_USDHC2>;
> +	assigned-clock-rates = <400000000>;
> +	vmmc-supply = <&reg_usdhc2_vmmc>;
> +	bus-width = <4>;
> +	disable-wp;
> +	no-sdio;
> +	no-mmc;
> +	status = "okay";
> +};
> +
> +&iomuxc {
> +	pinctrl_eqos: eqosgrp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC				0x3
> +			MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO				0x3
> +			MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0			0x91
> +			MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1			0x91
> +			MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2			0x91
> +			MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3			0x91
> +			MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK	0x91
> +			MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL			0x91
> +			MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0			0x1f
> +			MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1			0x1f
> +			MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2			0x1f
> +			MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3			0x1f
> +			MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL			0x1f
> +			MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK	0x1f
> +
> +			MX8MP_IOMUXC_SAI1_RXFS__ENET1_1588_EVENT0_IN			0x1f
> +			MX8MP_IOMUXC_SAI1_TXD6__GPIO4_IO18				0x19
> +		>;
> +	};
> +
> +	pinctrl_fec: fecgrp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC		0x3
> +			MX8MP_IOMUXC_SAI1_RXD3__ENET1_MDIO		0x3
> +			MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0		0x91
> +			MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1		0x91
> +			MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2		0x91
> +			MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3		0x91
> +			MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC		0x91
> +			MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL	0x91
> +			MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0		0x1f
> +			MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1		0x1f
> +			MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2		0x1f
> +			MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3		0x1f
> +			MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL	0x1f
> +			MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC		0x1f
> +			MX8MP_IOMUXC_SAI1_RXD0__ENET1_1588_EVENT1_IN    0x1f
> +			MX8MP_IOMUXC_SAI1_TXD7__GPIO4_IO19		0x19
> +		>;
> +	};
> +
> +	pinctrl_flexcan1: flexcan1grp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_SAI5_RXD2__CAN1_RX			0x154
> +			MX8MP_IOMUXC_SAI5_RXD1__CAN1_TX			0x154
> +		>;
> +	};
> +
> +	pinctrl_flexcan2: flexcan2grp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_SAI5_MCLK__CAN2_RX			0x154
> +			MX8MP_IOMUXC_SAI5_RXD3__CAN2_TX			0x154
> +		>;
> +	};
> +
> +	pinctrl_flexspi0: flexspi0grp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_NAND_ALE__FLEXSPI_A_SCLK           0x1c2
> +			MX8MP_IOMUXC_NAND_CE0_B__FLEXSPI_A_SS0_B        0x82
> +			MX8MP_IOMUXC_NAND_DATA00__FLEXSPI_A_DATA00      0x82
> +			MX8MP_IOMUXC_NAND_DATA01__FLEXSPI_A_DATA01      0x82
> +			MX8MP_IOMUXC_NAND_DATA02__FLEXSPI_A_DATA02      0x82
> +			MX8MP_IOMUXC_NAND_DATA03__FLEXSPI_A_DATA03      0x82
> +		>;
> +	};
> +
> +	pinctrl_i2c1: i2c1grp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL			0x400001c2
> +			MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA			0x400001c2
> +		>;
> +	};
> +
> +	pinctrl_i2c4: i2c4grp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_I2C4_SCL__I2C4_SCL			0x400001c3
> +			MX8MP_IOMUXC_I2C4_SDA__I2C4_SDA			0x400001c3
> +		>;
> +	};
> +
> +	pinctrl_rtc: rtcgrp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_SAI1_RXD1__GPIO4_IO03		0x140
> +		>;
> +	};
> +
> +	pinctrl_pmic: pmicgrp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03		0x41
> +		>;
> +	};
> +
> +	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19		0x41
> +		>;
> +	};
> +
> +	pinctrl_uart2: uart2grp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX		0x14f
> +			MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX		0x14f
> +		>;
> +	};
> +
> +	pinctrl_uart3: uart3grp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_UART3_RXD__UART3_DCE_RX		0x49
> +			MX8MP_IOMUXC_UART3_TXD__UART3_DCE_TX		0x49
> +		>;
> +	};
> +
> +	pinctrl_uart4: uart4grp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_UART4_RXD__UART4_DCE_RX		0x49
> +			MX8MP_IOMUXC_UART4_TXD__UART4_DCE_TX		0x49
> +		>;
> +	};
> +
> +	pinctrl_usdhc2: usdhc2grp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK		0x190
> +			MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD		0x1d0
> +			MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0		0x1d0
> +			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1		0x1d0
> +			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2		0x1d0
> +			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3		0x1d0
> +			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT		0xc1
> +		>;
> +	};
> +
> +	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK		0x194
> +			MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD		0x1d4
> +			MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0		0x1d4
> +			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1		0x1d4
> +			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2		0x1d4
> +			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3		0x1d4
> +			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT		0xc1
> +		>;
> +	};
> +
> +	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK		0x196
> +			MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD		0x1d6
> +			MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0		0x1d6
> +			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1		0x1d6
> +			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2		0x1d6
> +			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3		0x1d6
> +			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT		0xc1
> +		>;
> +	};
> +};
> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a.dtsi
> new file mode 100644
> index 0000000000000..a089cadacc105
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a.dtsi
> @@ -0,0 +1,266 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2019 NXP
> + * Copyright (C) 2023 Pengutronix, Marco Felsch <kernel at pengutronix.de>
> + */
> +
> +#include "imx8mp.dtsi"
> +
> +/ {
> +	model = "Polyhex i.MX8MPlus Debix SOM A";
> +	compatible = "polyhex,imx8mp-debix-som-a", "fsl,imx8mp";
> +};
> +
> +&A53_0 {
> +	cpu-supply = <&buck2>;
> +};
> +
> +&A53_1 {
> +	cpu-supply = <&buck2>;
> +};
> +
> +&A53_2 {
> +	cpu-supply = <&buck2>;
> +};
> +
> +&A53_3 {
> +	cpu-supply = <&buck2>;
> +};
> +
> +&i2c1 {
> +	clock-frequency = <400000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c1>;
> +	status = "okay";
> +
> +	pmic at 25 {
> +		compatible = "nxp,pca9450c";
> +		reg = <0x25>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_pmic>;
> +		interrupt-parent = <&gpio1>;
> +		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
> +
> +		regulators {
> +			buck1: BUCK1 {
> +				regulator-name = "BUCK1";
> +				regulator-min-microvolt = <600000>;
> +				regulator-max-microvolt = <2187500>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +				regulator-ramp-delay = <3125>;
> +			};
> +
> +			buck2: BUCK2 {
> +				regulator-name = "BUCK2";
> +				regulator-min-microvolt = <600000>;
> +				regulator-max-microvolt = <2187500>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +				regulator-ramp-delay = <3125>;
> +				nxp,dvs-run-voltage = <950000>;
> +				nxp,dvs-standby-voltage = <850000>;
> +			};
> +
> +			buck4: BUCK4 {
> +				regulator-name = "BUCK4";
> +				regulator-min-microvolt = <600000>;
> +				regulator-max-microvolt = <3400000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			buck5: BUCK5 {
> +				regulator-name = "BUCK5";
> +				regulator-min-microvolt = <600000>;
> +				regulator-max-microvolt = <3400000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			buck6: BUCK6 {
> +				regulator-name = "BUCK6";
> +				regulator-min-microvolt = <600000>;
> +				regulator-max-microvolt = <3400000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			ldo1: LDO1 {
> +				regulator-name = "LDO1";
> +				regulator-min-microvolt = <1600000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			ldo2: LDO2 {
> +				regulator-name = "LDO2";
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <1150000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			ldo3: LDO3 {
> +				regulator-name = "LDO3";
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			ldo4: LDO4 {
> +				regulator-name = "LDO4";
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			ldo5: LDO5 {
> +				regulator-name = "LDO5";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +		};
> +	};
> +};
> +
> +&i2c4 {
> +	clock-frequency = <400000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c4>;
> +	status = "okay";
> +
> +	adc at 48 {
> +		 compatible = "ti,ads1115";
> +		 reg = <0x48>;
> +
> +		 #address-cells = <1>;
> +		 #size-cells = <0>;
> +
> +		 channel at 4 {
> +			 reg = <4>;
> +			 ti,gain = <1>;
> +			 ti,datarate = <7>;
> +		 };
> +		 channel at 5 {
> +			 reg = <5>;
> +			 ti,gain = <1>;
> +			 ti,datarate = <7>;
> +		 };
> +		 channel at 6 {
> +			 reg = <6>;
> +			 ti,gain = <1>;
> +			 ti,datarate = <7>;
> +		 };
> +		 channel at 7 {
> +			 reg = <7>;
> +			 ti,gain = <1>;
> +			 ti,datarate = <7>;
> +		 };
> +	 };
> +};
> +
> +&snvs_pwrkey {
> +	status = "okay";
> +};
> +
> +/* eMMC */
> +&usdhc3 {
> +	pinctrl-names = "default", "state_100mhz", "state_200mhz";
> +	pinctrl-0 = <&pinctrl_usdhc3>;
> +	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
> +	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
> +	assigned-clocks = <&clk IMX8MP_CLK_USDHC3>;
> +	assigned-clock-rates = <400000000>;
> +	bus-width = <8>;
> +	non-removable;
> +	status = "okay";
> +};
> +
> +&wdog1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_wdog>;
> +	fsl,ext-reset-output;
> +	status = "okay";
> +};
> +
> +&iomuxc {
> +	pinctrl_i2c1: i2c1grp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL			0x400001c2
> +			MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA			0x400001c2
> +		>;
> +	};
> +
> +	pinctrl_i2c4: i2c4grp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_I2C4_SCL__I2C4_SCL			0x400001c3
> +			MX8MP_IOMUXC_I2C4_SDA__I2C4_SDA			0x400001c3
> +		>;
> +	};
> +
> +	pinctrl_pmic: pmicgrp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03		0x41
> +		>;
> +	};
> +
> +	pinctrl_usdhc3: usdhc3grp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK		0x190
> +			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD		0x1d0
> +			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0		0x1d0
> +			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1		0x1d0
> +			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2		0x1d0
> +			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3		0x1d0
> +			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4		0x1d0
> +			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5		0x1d0
> +			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6		0x1d0
> +			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7		0x1d0
> +			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE		0x190
> +		>;
> +	};
> +
> +	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK		0x194
> +			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD		0x1d4
> +			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0		0x1d4
> +			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1		0x1d4
> +			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2		0x1d4
> +			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3		0x1d4
> +			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4		0x1d4
> +			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5		0x1d4
> +			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6		0x1d4
> +			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7		0x1d4
> +			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE		0x194
> +		>;
> +	};
> +
> +	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK		0x196
> +			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD		0x1d6
> +			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0		0x1d6
> +			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1		0x1d6
> +			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2		0x1d6
> +			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3		0x1d6
> +			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4		0x1d6
> +			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5		0x1d6
> +			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6		0x1d6
> +			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7		0x1d6
> +			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE		0x196
> +		>;
> +	};
> +
> +	pinctrl_wdog: wdoggrp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B		0xc6
> +		>;
> +	};
> +};

-- 
Regards,

Laurent Pinchart



More information about the linux-arm-kernel mailing list