[PATCH v3] arm64: dts: ti: k3-j721e: Add overlay to enable CPSW9G ports with GESI
Siddharth Vadapalli
s-vadapalli at ti.com
Tue Jul 25 00:30:57 PDT 2023
The J7 GESI EXP board for J721E Common-Proc-Board supports RGMII mode.
Use the overlay to configure CPSW9G ports in RGMII-RXID mode.
Add aliases for CPSW9G ports to enable kernel to fetch MAC addresses
directly from U-Boot.
Signed-off-by: Siddharth Vadapalli <s-vadapalli at ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran at ti.com>
---
NOTE: This patch is based on linux-next tagged next-20230725.
v2:
https://lore.kernel.org/r/20230710075551.1109024-1-s-vadapalli@ti.com/
Changes since v2:
- Collect Reviewed-by tag from Ravi Gunasekaran <r-gunasekaran at ti.com>
- Rename rgmii1_pins_default, rgmii2_pins_default, rgmii3_pins_default,
rgmii4_pins_default and mdio0_pins_default to:
rgmii1_default_pins, rgmii2_default_pins, rgmii3_default_pins,
rgmii4_default_pins and mdio0_default_pins respectively.
- Rename rgmii1-pins-default, rgmii2-pins-default, rgmii3-pins-default,
rgmii4-pins-default and mdio0-pins-default to:
rgmii1-default-pins, rgmii2-default-pins, rgmii3-default-pins,
rgmii4-default-pins and mdio0-default-pins respectively.
- The above changes are performed to follow the updated json-schema
patch at:
https://lore.kernel.org/all/169021456020.3622493.10284534202541859578.robh@kernel.org/
v1:
https://lore.kernel.org/r/20230529094222.512675-1-s-vadapalli@ti.com/
Changes since v1:
- Rebase on linux-next tagged next-20230710.
arch/arm64/boot/dts/ti/Makefile | 2 +
.../dts/ti/k3-j721e-evm-gesi-exp-board.dtso | 196 ++++++++++++++++++
2 files changed, 198 insertions(+)
create mode 100644 arch/arm64/boot/dts/ti/k3-j721e-evm-gesi-exp-board.dtso
diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index 6dd7b6f1d6ab..01d58aa8b06e 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -46,6 +46,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-j7200-evm.dtb
k3-j721e-evm-dtbs := k3-j721e-common-proc-board.dtb k3-j721e-evm-quad-port-eth-exp.dtbo
dtb-$(CONFIG_ARCH_K3) += k3-j721e-beagleboneai64.dtb
dtb-$(CONFIG_ARCH_K3) += k3-j721e-evm.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-j721e-evm-gesi-exp-board.dtbo
dtb-$(CONFIG_ARCH_K3) += k3-j721e-sk.dtb
# Boards with J721s2 SoC
@@ -58,3 +59,4 @@ dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm.dtb
# Enable support for device-tree overlays
DTC_FLAGS_k3-am6548-iot2050-advanced-m2 += -@
+DTC_FLAGS_k3-j721e-common-proc-board += -@
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-evm-gesi-exp-board.dtso b/arch/arm64/boot/dts/ti/k3-j721e-evm-gesi-exp-board.dtso
new file mode 100644
index 000000000000..6a7d37575da1
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-j721e-evm-gesi-exp-board.dtso
@@ -0,0 +1,196 @@
+// SPDX-License-Identifier: GPL-2.0
+/**
+ * DT Overlay for CPSW9G in RGMII mode using J7 GESI EXP BRD board with
+ * J721E board.
+ *
+ * GESI Board Product Link: https://www.ti.com/tool/J7EXPCXEVM
+ *
+ * Copyright (C) 2023 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/net/ti-dp83867.h>
+
+#include "k3-pinctrl.h"
+
+&{/} {
+ aliases {
+ ethernet1 = "/bus at 100000/ethernet at c000000/ethernet-ports/port at 1";
+ ethernet2 = "/bus at 100000/ethernet at c000000/ethernet-ports/port at 2";
+ ethernet3 = "/bus at 100000/ethernet at c000000/ethernet-ports/port at 3";
+ ethernet4 = "/bus at 100000/ethernet at c000000/ethernet-ports/port at 4";
+ };
+};
+
+&cpsw0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii1_default_pins
+ &rgmii2_default_pins
+ &rgmii3_default_pins
+ &rgmii4_default_pins>;
+};
+
+&cpsw0_port1 {
+ status = "okay";
+ phy-handle = <&cpsw9g_phy12>;
+ phy-mode = "rgmii-rxid";
+ mac-address = [00 00 00 00 00 00];
+ phys = <&cpsw0_phy_gmii_sel 1>;
+};
+
+&cpsw0_port2 {
+ status = "okay";
+ phy-handle = <&cpsw9g_phy15>;
+ phy-mode = "rgmii-rxid";
+ mac-address = [00 00 00 00 00 00];
+ phys = <&cpsw0_phy_gmii_sel 2>;
+};
+
+&cpsw0_port3 {
+ status = "okay";
+ phy-handle = <&cpsw9g_phy0>;
+ phy-mode = "rgmii-rxid";
+ mac-address = [00 00 00 00 00 00];
+ phys = <&cpsw0_phy_gmii_sel 3>;
+};
+
+&cpsw0_port4 {
+ status = "okay";
+ phy-handle = <&cpsw9g_phy3>;
+ phy-mode = "rgmii-rxid";
+ mac-address = [00 00 00 00 00 00];
+ phys = <&cpsw0_phy_gmii_sel 4>;
+};
+
+&cpsw9g_mdio {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mdio0_default_pins>;
+ bus_freq = <1000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpsw9g_phy0: ethernet-phy at 0 {
+ reg = <0>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ ti,min-output-impedance;
+ };
+ cpsw9g_phy3: ethernet-phy at 3 {
+ reg = <3>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ ti,min-output-impedance;
+ };
+ cpsw9g_phy12: ethernet-phy at 12 {
+ reg = <12>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ ti,min-output-impedance;
+ };
+ cpsw9g_phy15: ethernet-phy at 15 {
+ reg = <15>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ ti,min-output-impedance;
+ };
+};
+
+&exp1 {
+ p15-hog {
+ /* P15 - EXP_MUX2 */
+ gpio-hog;
+ gpios = <13 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "EXP_MUX2";
+ };
+
+ p16-hog {
+ /* P16 - EXP_MUX3 */
+ gpio-hog;
+ gpios = <14 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "EXP_MUX3";
+ };
+};
+
+&main_pmx0 {
+ mdio0_default_pins: mdio0-default-pins {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x1bc, PIN_OUTPUT, 0) /* (V24) MDIO0_MDC */
+ J721E_IOPAD(0x1b8, PIN_INPUT, 0) /* (V26) MDIO0_MDIO */
+ >;
+ };
+
+ rgmii1_default_pins: rgmii1-default-pins {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x4, PIN_INPUT, 4) /* (AC23) PRG1_PRU0_GPO0.RGMII1_RD0 */
+ J721E_IOPAD(0x8, PIN_INPUT, 4) /* (AG22) PRG1_PRU0_GPO1.RGMII1_RD1 */
+ J721E_IOPAD(0xc, PIN_INPUT, 4) /* (AF22) PRG1_PRU0_GPO2.RGMII1_RD2 */
+ J721E_IOPAD(0x10, PIN_INPUT, 4) /* (AJ23) PRG1_PRU0_GPO3.RGMII1_RD3 */
+ J721E_IOPAD(0x1c, PIN_INPUT, 4) /* (AD22) PRG1_PRU0_GPO6.RGMII1_RXC */
+ J721E_IOPAD(0x14, PIN_INPUT, 4) /* (AH23) PRG1_PRU0_GPO4.RGMII1_RX_CTL */
+ J721E_IOPAD(0x30, PIN_OUTPUT, 4) /* (AF24) PRG1_PRU0_GPO11.RGMII1_TD0 */
+ J721E_IOPAD(0x34, PIN_OUTPUT, 4) /* (AJ24) PRG1_PRU0_GPO12.RGMII1_TD1 */
+ J721E_IOPAD(0x38, PIN_OUTPUT, 4) /* (AG24) PRG1_PRU0_GPO13.RGMII1_TD2 */
+ J721E_IOPAD(0x3c, PIN_OUTPUT, 4) /* (AD24) PRG1_PRU0_GPO14.RGMII1_TD3 */
+ J721E_IOPAD(0x44, PIN_OUTPUT, 4) /* (AE24) PRG1_PRU0_GPO16.RGMII1_TXC */
+ J721E_IOPAD(0x40, PIN_OUTPUT, 4) /* (AC24) PRG1_PRU0_GPO15.RGMII1_TX_CTL */
+ >;
+ };
+
+ rgmii2_default_pins: rgmii2-default-pins {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x58, PIN_INPUT, 4) /* (AE22) PRG1_PRU1_GPO0.RGMII2_RD0 */
+ J721E_IOPAD(0x5c, PIN_INPUT, 4) /* (AG23) PRG1_PRU1_GPO1.RGMII2_RD1 */
+ J721E_IOPAD(0x60, PIN_INPUT, 4) /* (AF23) PRG1_PRU1_GPO2.RGMII2_RD2 */
+ J721E_IOPAD(0x64, PIN_INPUT, 4) /* (AD23) PRG1_PRU1_GPO3.RGMII2_RD3 */
+ J721E_IOPAD(0x70, PIN_INPUT, 4) /* (AE23) PRG1_PRU1_GPO6.RGMII2_RXC */
+ J721E_IOPAD(0x68, PIN_INPUT, 4) /* (AH24) PRG1_PRU1_GPO4.RGMII2_RX_CTL */
+ J721E_IOPAD(0x84, PIN_OUTPUT, 4) /* (AJ25) PRG1_PRU1_GPO11.RGMII2_TD0 */
+ J721E_IOPAD(0x88, PIN_OUTPUT, 4) /* (AH25) PRG1_PRU1_GPO12.RGMII2_TD1 */
+ J721E_IOPAD(0x8c, PIN_OUTPUT, 4) /* (AG25) PRG1_PRU1_GPO13.RGMII2_TD2 */
+ J721E_IOPAD(0x90, PIN_OUTPUT, 4) /* (AH26) PRG1_PRU1_GPO14.RGMII2_TD3 */
+ J721E_IOPAD(0x98, PIN_OUTPUT, 4) /* (AJ26) PRG1_PRU1_GPO16.RGMII2_TXC */
+ J721E_IOPAD(0x94, PIN_OUTPUT, 4) /* (AJ27) PRG1_PRU1_GPO15.RGMII2_TX_CTL */
+ >;
+ };
+
+ rgmii3_default_pins: rgmii3-default-pins {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0xb0, PIN_INPUT, 4) /* (AF28) PRG0_PRU0_GPO0.RGMII3_RD0 */
+ J721E_IOPAD(0xb4, PIN_INPUT, 4) /* (AE28) PRG0_PRU0_GPO1.RGMII3_RD1 */
+ J721E_IOPAD(0xb8, PIN_INPUT, 4) /* (AE27) PRG0_PRU0_GPO2.RGMII3_RD2 */
+ J721E_IOPAD(0xbc, PIN_INPUT, 4) /* (AD26) PRG0_PRU0_GPO3.RGMII3_RD3 */
+ J721E_IOPAD(0xc8, PIN_INPUT, 4) /* (AE26) PRG0_PRU0_GPO6.RGMII3_RXC */
+ J721E_IOPAD(0xc0, PIN_INPUT, 4) /* (AD25) PRG0_PRU0_GPO4.RGMII3_RX_CTL */
+ J721E_IOPAD(0xdc, PIN_OUTPUT, 4) /* (AJ28) PRG0_PRU0_GPO11.RGMII3_TD0 */
+ J721E_IOPAD(0xe0, PIN_OUTPUT, 4) /* (AH27) PRG0_PRU0_GPO12.RGMII3_TD1 */
+ J721E_IOPAD(0xe4, PIN_OUTPUT, 4) /* (AH29) PRG0_PRU0_GPO13.RGMII3_TD2 */
+ J721E_IOPAD(0xe8, PIN_OUTPUT, 4) /* (AG28) PRG0_PRU0_GPO14.RGMII3_TD3 */
+ J721E_IOPAD(0xf0, PIN_OUTPUT, 4) /* (AH28) PRG0_PRU0_GPO16.RGMII3_TXC */
+ J721E_IOPAD(0xec, PIN_OUTPUT, 4) /* (AG27) PRG0_PRU0_GPO15.RGMII3_TX_CTL */
+ >;
+ };
+
+ rgmii4_default_pins: rgmii4-default-pins {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x100, PIN_INPUT, 4) /* (AE29) PRG0_PRU1_GPO0.RGMII4_RD0 */
+ J721E_IOPAD(0x104, PIN_INPUT, 4) /* (AD28) PRG0_PRU1_GPO1.RGMII4_RD1 */
+ J721E_IOPAD(0x108, PIN_INPUT, 4) /* (AD27) PRG0_PRU1_GPO2.RGMII4_RD2 */
+ J721E_IOPAD(0x10c, PIN_INPUT, 4) /* (AC25) PRG0_PRU1_GPO3.RGMII4_RD3 */
+ J721E_IOPAD(0x118, PIN_INPUT, 4) /* (AC26) PRG0_PRU1_GPO6.RGMII4_RXC */
+ J721E_IOPAD(0x110, PIN_INPUT, 4) /* (AD29) PRG0_PRU1_GPO4.RGMII4_RX_CTL */
+ J721E_IOPAD(0x12c, PIN_OUTPUT, 4) /* (AG26) PRG0_PRU1_GPO11.RGMII4_TD0 */
+ J721E_IOPAD(0x130, PIN_OUTPUT, 4) /* (AF27) PRG0_PRU1_GPO12.RGMII4_TD1 */
+ J721E_IOPAD(0x134, PIN_OUTPUT, 4) /* (AF26) PRG0_PRU1_GPO13.RGMII4_TD2 */
+ J721E_IOPAD(0x138, PIN_OUTPUT, 4) /* (AE25) PRG0_PRU1_GPO14.RGMII4_TD3 */
+ J721E_IOPAD(0x140, PIN_OUTPUT, 4) /* (AG29) PRG0_PRU1_GPO16.RGMII4_TXC */
+ J721E_IOPAD(0x13c, PIN_OUTPUT, 4) /* (AF29) PRG0_PRU1_GPO15.RGMII4_TX_CTL */
+ >;
+ };
+};
--
2.34.1
More information about the linux-arm-kernel
mailing list