Aw: Re: [PATCH net-next 0/4] Remove legacy phylink behaviour

[Daniel Golle]

On Sat, Jul 22, 2023 at 02:31:45PM +0200, Frank Wunderlich wrote:
> Hi
> 
> > Gesendet: Samstag, 22. Juli 2023 um 00:40 Uhr
> > Von: "Daniel Golle" <daniel at makrotopia.org>
> >
> > Hi Russell,
> >
> > On Fri, Jul 21, 2023 at 12:33:52PM +0100, Russell King (Oracle) wrote:
> > > Hi,
> > >
> > > This series removes the - as far as I can tell - unreachable code in
> > > mtk_eth_soc that relies upon legacy phylink behaviour, and then removes
> > > the support in phylink for this legacy behaviour.
> > >
> > > Patch 1 removes the clocking configuration from mtk_eth_soc for non-
> > > TRGMII, non-serdes based interface modes, and disables those interface
> > > modes prior to phylink configuration.
> > >
> > > Patch 2 removes the mac_pcs_get_state() method from mtk_eth_soc which
> > > I believe is also not used - mtk_eth_soc appears not to be used with
> > > SFPs (which would use a kind of in-band mode) nor does any DT appear
> > > to specify in-band mode for any non-serdes based interface mode.
> > >
> > > With both of those dealt with, the kernel is now free of any driver
> > > relying on the phylink legacy mode. Therefore, patch 3 removes support
> > > for this.
> > >
> > > Finally, with the advent of a new driver being submitted today that
> > > makes use of state->speed in the mac_config() path, patch 4 ensures that
> > > any phylink_link_state member that should not be used in mac_config is
> > > either cleared or set to an invalid value.
> >
> > Thank you for taking care of this!
> 
> > For the whole series:
> >
> > Reviewed-by: Daniel Golle <daniel at makrotopia.org>
> > Tested-by: Daniel Golle <daniel at makrotopia.org>
> >
> > Tested on BPi-R2 (MT7623N), BPi-R3 (MT7986A) and BPi-R64 (MT7622A).
> > All works fine as expected.
> 
> have you changed anything?
> 
> in my test with bpi-r2 i see boot hangs after link-up on my wan-port (still trgmii-mode configured), no access to userspace.
> 
> [   10.881844] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/trgmii link mode
> [   10.891611] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
> [   11.005814] mt7530-mdio mdio-bus:1f wan: configuring for phy/gmii link mode
> [   11.016654] mt7530-mdio mdio-bus:1f lan3: configuring for phy/gmii link mode
> [   11.025685] mt7530-mdio mdio-bus:1f lan2: configuring for phy/gmii link mode
> [   11.035122] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode
> [   11.045370] mt7530-mdio mdio-bus:1f lan0: configuring for phy/gmii link mode
> 
> [   15.144255] mt7530-mdio mdio-bus:1f wan: Link is Up - 1Gbps/Full - flow control rx/tx
> 
> removing the cable does not show link down so it looks like completely stalled...but also no panic/crash or similar.
> When booting without cable it hangs too (without the up-message of course).
> 
> > To apply the series I needed to resolve a minor conflict due to
> > net: ethernet: mtk_ppe: add MTK_FOE_ENTRY_V{1,2}_SIZE macros
> > being applied in the meantime.
> 
> i used yesterdays net-next (6.5-rc2) and put series on top (also needed to do one hunk of first patch manually) and
> then my defconfig,buildscript etc. maybe i miss anything?

I tested in a fairly similar way.

> 
> afair trgmii is basicly rgmii only with higher clock-setting...and if this is dropped from mac-driver but switch is still using it it cannot work, but i'm sure you know this ;)

For TRGMII mode mtk_gmac0_rgmii_adjust behavior should not have changed,
only speed-dependent adjustments for RGMII have been dropped.
I also didn't not see such a problem when I was testing.

However, I guess in my case the MAC interface mode has already been
setup in hardware because I booted the board via TFTP, hence U-Boot
already took care of initializing everything, so that can also be
a reason why it worked fine for me.