[PATCH] ARM: dts: at91: sam9x60: fix the SOC detection

[Durai Manickam KR]

Remove the dbgu compatible strings in the UART submodule of the
flexcom for the proper SOC detection.

Fixes: 99c808335877 (ARM: dts: at91: sam9x60: Add missing flexcom definitions)
Signed-off-by: Durai Manickam KR <durai.manickamkr at microchip.com>
---
 arch/arm/boot/dts/microchip/sam9x60.dtsi | 26 ++++++++++++------------
 1 file changed, 13 insertions(+), 13 deletions(-)

diff --git a/arch/arm/boot/dts/microchip/sam9x60.dtsi b/arch/arm/boot/dts/microchip/sam9x60.dtsi
index 8b53997675e7..73d570a17269 100644
--- a/arch/arm/boot/dts/microchip/sam9x60.dtsi
+++ b/arch/arm/boot/dts/microchip/sam9x60.dtsi
@@ -172,7 +172,7 @@ flx4: flexcom at f0000000 {
 				status = "disabled";
 
 				uart4: serial at 200 {
-					compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
 					reg = <0x200 0x200>;
 					interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
 					dmas = <&dma0
@@ -240,7 +240,7 @@ flx5: flexcom at f0004000 {
 				status = "disabled";
 
 				uart5: serial at 200 {
-					compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
 					reg = <0x200 0x200>;
 					atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 					interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -370,7 +370,7 @@ flx11: flexcom at f0020000 {
 				status = "disabled";
 
 				uart11: serial at 200 {
-					compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
 					reg = <0x200 0x200>;
 					interrupts = <32 IRQ_TYPE_LEVEL_HIGH 7>;
 					dmas = <&dma0
@@ -419,7 +419,7 @@ flx12: flexcom at f0024000 {
 				status = "disabled";
 
 				uart12: serial at 200 {
-					compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
 					reg = <0x200 0x200>;
 					interrupts = <33 IRQ_TYPE_LEVEL_HIGH 7>;
 					dmas = <&dma0
@@ -576,7 +576,7 @@ flx6: flexcom at f8010000 {
 				status = "disabled";
 
 				uart6: serial at 200 {
-					compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
 					reg = <0x200 0x200>;
 					interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
 					dmas = <&dma0
@@ -625,7 +625,7 @@ flx7: flexcom at f8014000 {
 				status = "disabled";
 
 				uart7: serial at 200 {
-					compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
 					reg = <0x200 0x200>;
 					interrupts = <10 IRQ_TYPE_LEVEL_HIGH 7>;
 					dmas = <&dma0
@@ -674,7 +674,7 @@ flx8: flexcom at f8018000 {
 				status = "disabled";
 
 				uart8: serial at 200 {
-					compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
 					reg = <0x200 0x200>;
 					interrupts = <11 IRQ_TYPE_LEVEL_HIGH 7>;
 					dmas = <&dma0
@@ -723,7 +723,7 @@ flx0: flexcom at f801c000 {
 				status = "disabled";
 
 				uart0: serial at 200 {
-					compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
 					reg = <0x200 0x200>;
 					interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
 					dmas = <&dma0
@@ -791,7 +791,7 @@ flx1: flexcom at f8020000 {
 				status = "disabled";
 
 				uart1: serial at 200 {
-					compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
 					reg = <0x200 0x200>;
 					interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
 					dmas = <&dma0
@@ -859,7 +859,7 @@ flx2: flexcom at f8024000 {
 				status = "disabled";
 
 				uart2: serial at 200 {
-					compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
 					reg = <0x200 0x200>;
 					interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
 					dmas = <&dma0
@@ -927,7 +927,7 @@ flx3: flexcom at f8028000 {
 				status = "disabled";
 
 				uart3: serial at 200 {
-					compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
 					reg = <0x200 0x200>;
 					interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
 					dmas = <&dma0
@@ -1050,7 +1050,7 @@ flx9: flexcom at f8040000 {
 				status = "disabled";
 
 				uart9: serial at 200 {
-					compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
 					reg = <0x200 0x200>;
 					interrupts = <15 IRQ_TYPE_LEVEL_HIGH 7>;
 					dmas = <&dma0
@@ -1099,7 +1099,7 @@ flx10: flexcom at f8044000 {
 				status = "disabled";
 
 				uart10: serial at 200 {
-					compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
 					reg = <0x200 0x200>;
 					interrupts = <16 IRQ_TYPE_LEVEL_HIGH 7>;
 					dmas = <&dma0
-- 
2.25.1