imx8mp mipi csi camera overlay: Unable to retrieve endpoint for port at 1
Kieran Bingham
kieran.bingham at ideasonboard.com
Tue Jul 11 15:49:54 PDT 2023
Hi Tim,
Quoting Tim Harvey (2023-07-11 23:16:33)
> On Mon, Jul 10, 2023 at 6:09 PM Adam Ford <aford173 at gmail.com> wrote:
> >
> > On Mon, Jul 10, 2023 at 7:59 PM Tim Harvey <tharvey at gateworks.com> wrote:
> > >
> > > On Fri, Jul 7, 2023 at 6:11 PM Adam Ford <aford173 at gmail.com> wrote:
> > > >
> > > > On Fri, Jul 7, 2023 at 7:28 PM Tim Harvey <tharvey at gateworks.com> wrote:
> > > > >
> > > > > Greetings,
> > > > >
> > > > > I have an imx219 camera connected to an imx8mp-venice-gw74xx via the
> > > > > following details:
> > > > > - camera is a RaspberryPi Camera v2 -
> > > > > https://datasheets.raspberrypi.com/camera/camera-v2-schematics.pdf
> > > > > - has its own on-board 24MHz osc so no clock is required from the baseboard
> > > > > - pin 11 on the camera enables 1.8V and 2.8V LDO which is connected to
> > > > > IMX8MP GPIO1_IO1 so we use that as a gpio regulator
> > > > > - MIPI_CSI1 lanes 0 and 1 are used
> > > > >
> > > > > I'm using Linux 6.4 with Laurent's pending patch to add the MIPI CSI
> > > > > DT nodes to imx8mp.dtsi [1] as follows:
> > > > >
> > > > > #include <dt-bindings/gpio/gpio.h>
> > > > > #include "imx8mp-pinfunc.h"
> > > > >
> > > > > /dts-v1/;
> > > > > /plugin/;
> > > > >
> > > > > &{/} {
> > > > > compatible = "gw,imx8mp-gw74xx", "fsl,imx8mp";
> > > > >
> > > > > reg_cam: regulator-cam {
> > > > > pinctrl-names = "default";
> > > > > pinctrl-0 = <&pinctrl_reg_cam>;
> > > > > compatible = "regulator-fixed";
> > > > > regulator-name = "reg_cam";
> > > > > gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>;
> > > > > enable-active-high;
> > > > > regulator-min-microvolt = <1800000>;
> > > > > regulator-max-microvolt = <1800000>;
> > > > > };
> > > > >
> > > > > cam24m: cam24m {
> > > > > compatible = "fixed-clock";
> > > > > #clock-cells = <0>;
> > > > > clock-frequency = <24000000>;
> > > > > clock-output-names = "cam24m";
> > > > > };
> > > > > };
> > > > >
> > > > > &i2c3 {
> > > > > #address-cells = <1>;
> > > > > #size-cells = <0>;
> > > > >
> > > > > imx219: sensor at 10 {
> > > > > compatible = "sony,imx219";
> > > > > reg = <0x10>;
> > > > > clocks = <&cam24m>;
> > > > > VDIG-supply = <®_cam>;
> > > > >
> > > > > port {
> > > > > /* MIPI CSI-2 bus endpoint */
> > > > > imx219_to_mipi_csi2: endpoint {
> > > > > remote-endpoint = <&mipi_csi_0_in>;
> > > > > clock-lanes = <0>;
> > > > > data-lanes = <1 2>;
> > > > > link-frequencies = /bits/ 64 <456000000>;
> > > > > };
> > > > > };
> > > > > };
> > > > > };
> > > > >
> > > > > &mipi_csi_0 {
> > > > > status = "okay";
> > > > >
> > > > > ports {
> > > > > port at 0 {
> > > > > mipi_csi_0_in: endpoint {
> > > > > remote-endpoint = <&imx219_to_mipi_csi2>;
> > > > > data-lanes = <1 2>;
> > > > > };
> > > > > };
> > > > > };
> > > > > };
> > > > >
> > > > > &iomuxc {
> > > > > pinctrl_reg_cam: regcamgrp {
> > > > > fsl,pins = <
> > > > > MX8MP_IOMUXC_GPIO1_IO01__GPIO1_IO01 0x41
> > > > > >;
> > > > > };
> > > > > };
> > > > >
> > > > > imx-mipi-csis fails to probe due to a missing port1 endpoint and I'm
> > > > > not clear what to do with that:
> > > > > imx-mipi-csis 32e40000.csi: Unable to retrieve endpoint for port at 1
> > > > > imx-mipi-csis: probe of 32e40000.csi failed with error -2
> > > > >
> > > > > Any suggestions?
> > > >
> > > > I think the port needs to point to an ISI node or a ISP node.
> > > > Linux-next shows port at 1 pointing to isi_in_0. In the patch you're
> > > > referencing, it appears that node at 1 is missing.
> > > >
> > > > Check out:
> > > >
> > > > https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/arch/arm64/boot/dts/freescale/imx8mp.dtsi?h=next-20230707&id=9da15c4c850dd53309e07d5611f33655f8f8c05d
> > > >
> > > > See if that helps.
> > > >
> > > > adam
> > > >
> > >
> > > Hi Adam,
> > >
> > > Thanks for the info. I didn't realize those patches were already in
> > > linux-next and I missed the fact that the ISI was related to the CSI
> > > (so I was missing the ISI patch and enabling that driver).
> > >
> > > I'm now using 6.5.0-rc1 which has the patches that add CSI and ISI
> > > nodes to the imx8mp.dtsi with the following dt fragment:
> > > #include <dt-bindings/gpio/gpio.h>
> > >
> > > #include "imx8mp-pinfunc.h"
> > >
> > > /dts-v1/;
> > > /plugin/;
> > >
> > > &{/} {
> > > compatible = "gw,imx8mp-gw74xx", "fsl,imx8mp";
> > >
> > > reg_cam: regulator-cam {
> > > pinctrl-names = "default";
> > > pinctrl-0 = <&pinctrl_reg_cam>;
> > > compatible = "regulator-fixed";
> > > regulator-name = "reg_cam";
> > > gpio = <&gpio1 4 GPIO_ACTIVE_HIGH>;
> > > enable-active-high;
> > > regulator-min-microvolt = <1800000>;
> > > regulator-max-microvolt = <1800000>;
> > > };
> > >
> > > cam24m: cam24m {
> > > compatible = "fixed-clock";
> > > #clock-cells = <0>;
> > > clock-frequency = <24000000>;
> > > clock-output-names = "cam24m";
> > > };
> > > };
> > >
> > > &i2c4 {
> > > #address-cells = <1>;
> > > #size-cells = <0>;
> > >
> > > imx219: sensor at 10 {
> > > compatible = "sony,imx219";
> > > reg = <0x10>;
> > > clocks = <&cam24m>;
> > > VDIG-supply = <®_cam>;
> > >
> > > port {
> > > /* MIPI CSI-2 bus endpoint */
> > > imx219_to_mipi_csi2: endpoint {
> > > remote-endpoint = <&mipi_csi_0_in>;
> > > clock-lanes = <0>;
> > > data-lanes = <1 2>;
> > > link-frequencies = /bits/ 64 <456000000>;
> > > };
> > > };
> > > };
> > > };
> > >
> > > &isi_0 {
> > > status = "okay";
> > > };
> > >
> > > &mipi_csi_0 {
> > > status = "okay";
> > >
> > > ports {
> > > port at 0 {
> > > mipi_csi_0_in: endpoint {
> > > remote-endpoint = <&imx219_to_mipi_csi2>;
> > > data-lanes = <1 2>;
> > > };
> > > };
> > > };
> > > };
> > >
> > > &iomuxc {
> > > pinctrl_reg_cam: regcamgrp {
> > > fsl,pins = <
> > > MX8MP_IOMUXC_GPIO1_IO04__GPIO1_IO04 0x41
> > > >;
> > > };
> > > };
> > >
> > > Now I'm getting:
> > > # dmesg | grep imx219
> > > [ 1.764111] imx219 2-0010: supply VANA not found, using dummy regulator
> > > [ 1.770953] imx219 2-0010: supply VDDL not found, using dummy regulator
> > > [ 5.520396] imx219 2-0010: Consider updating driver imx219 to match
> > > on endpoints
> > > # dmesg | grep mipi
> > > [ 2.080468] imx-mipi-csis 32e40000.csi: lanes: 2, freq: 500000000
> > > # cat /sys/bus/media/devices/media*/model
> > > FSL Capture Media Device
> > > hantro-vpu
> > > hantro-vpu
> > > # cat /sys/class/video4linux/video*/name
> > > mxc_isi.0.capture
> > > mxc_isi.1.capture
> > > mxc_isi.m2m
> > > nxp,imx8mm-vpu-g1-dec
> > > nxp,imx8mq-vpu-g2-dec
> > > # media-ctl /dev/media0 -p
> > > Media controller API version 6.5.0
> > >
> > > Media device information
> > > ------------------------
> > > driver mxc-isi
> > > model FSL Capture Media Device
> > > serial
> > > bus info platform:32e00000.isi
> > > hw revision 0x0
> > > driver version 6.5.0
> > >
> > > Device topology
> > > - entity 1: crossbar (5 pads, 4 links)
> > > type V4L2 subdev subtype Unknown flags 0
> > > device node name /dev/v4l-subdev0
> > > pad0: Sink
> > > [fmt:UYVY8_1X16/1920x1080 field:none colorspace:srgb
> > > xfer:srgb ycbcr:601 quantization:lim-range]
> > > <- "csis-32e40000.csi":1 [ENABLED,IMMUTABLE]
> > > pad1: Sink
> > > [fmt:UYVY8_1X16/1920x1080 field:none colorspace:srgb
> > > xfer:srgb ycbcr:601 quantization:lim-range]
> > > pad2: Sink
> > > <- "mxc_isi.output":0 [ENABLED,IMMUTABLE]
> > > pad3: Source
> > > [fmt:UYVY8_1X16/1920x1080 field:none colorspace:srgb
> > > xfer:srgb ycbcr:601 quantization:lim-range]
> > > -> "mxc_isi.0":0 [ENABLED,IMMUTABLE]
> > > pad4: Source
> > > [fmt:UYVY8_1X16/1920x1080 field:none colorspace:srgb
> > > xfer:srgb ycbcr:601 quantization:lim-range]
> > > -> "mxc_isi.1":0 [ENABLED,IMMUTABLE]
> > >
> > > - entity 7: mxc_isi.0 (2 pads, 2 links)
> > > type V4L2 subdev subtype Unknown flags 0
> > > device node name /dev/v4l-subdev1
> > > pad0: Sink
> > > [fmt:UYVY8_1X16/1920x1080 field:none colorspace:jpeg
> > > xfer:srgb ycbcr:601 quantization:full-range
> > > compose.bounds:(0,0)/1920x1080
> > > compose:(0,0)/1920x1080]
> > > <- "crossbar":3 [ENABLED,IMMUTABLE]
> > > pad1: Source
> > > [fmt:YUV8_1X24/1920x1080 field:none colorspace:jpeg
> > > xfer:srgb ycbcr:601 quantization:full-range
> > > crop.bounds:(0,0)/1920x1080
> > > crop:(0,0)/1920x1080]
> > > -> "mxc_isi.0.capture":0 [ENABLED,IMMUTABLE]
> > >
> > > - entity 10: mxc_isi.0.capture (1 pad, 1 link)
> > > type Node subtype V4L flags 0
> > > device node name /dev/video0
> > > pad0: Sink
> > > <- "mxc_isi.0":1 [ENABLED,IMMUTABLE]
> > >
> > > - entity 18: mxc_isi.1 (2 pads, 2 links)
> > > type V4L2 subdev subtype Unknown flags 0
> > > device node name /dev/v4l-subdev2
> > > pad0: Sink
> > > [fmt:UYVY8_1X16/1920x1080 field:none colorspace:jpeg
> > > xfer:srgb ycbcr:601 quantization:full-range
> > > compose.bounds:(0,0)/1920x1080
> > > compose:(0,0)/1920x1080]
> > > <- "crossbar":4 [ENABLED,IMMUTABLE]
> > > pad1: Source
> > > [fmt:YUV8_1X24/1920x1080 field:none colorspace:jpeg
> > > xfer:srgb ycbcr:601 quantization:full-range
> > > crop.bounds:(0,0)/1920x1080
> > > crop:(0,0)/1920x1080]
> > > -> "mxc_isi.1.capture":0 [ENABLED,IMMUTABLE]
> > >
> > > - entity 21: mxc_isi.1.capture (1 pad, 1 link)
> > > type Node subtype V4L flags 0
> > > device node name /dev/video1
> > > pad0: Sink
> > > <- "mxc_isi.1":1 [ENABLED,IMMUTABLE]
> > >
> > > - entity 29: mxc_isi.output (1 pad, 1 link)
> > > type Node subtype V4L flags 0
> > > pad0: Source
> > > -> "crossbar":2 [ENABLED,IMMUTABLE]
> > >
> > > - entity 36: csis-32e40000.csi (2 pads, 2 links)
> > > type V4L2 subdev subtype Unknown flags 0
> > > device node name /dev/v4l-subdev3
> > > pad0: Sink
> > > [fmt:UYVY8_1X16/640x480 field:none
> > > colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range]
> > > <- "imx219 3-0010":0 []
> > > pad1: Source
> > > [fmt:UYVY8_1X16/640x480 field:none
> > > colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range]
> > > -> "crossbar":0 [ENABLED,IMMUTABLE]
> > >
> > > - entity 41: imx219 3-0010 (1 pad, 1 link)
> > > type V4L2 subdev subtype Sensor flags 0
> > > device node name /dev/v4l-subdev4
> > > pad0: Source
> > > [fmt:SRGGB10_1X10/3280x2464 field:none colorspace:srgb
> > > xfer:srgb ycbcr:601 quantization:full-range
> > > crop.bounds:(8,8)/3280x2464
> > > crop:(8,8)/3280x2464]
> > > -> "csis-32e40000.csi":0 []
> > >
> > > # enable imx219 to csi link
> > > media-ctl --device /dev/media0 --links "'imx219
> > > 3-0010':0->'csis-32e40000.csi':0[1]"
> > >
> > > # v4l2-ctl --device /dev/video0 --all
> > > Driver Info:
> > > Driver name : mxc-isi
> > > Card type : mxc-isi-cap
> > > Bus info : platform:32e00000.isi
> > > Driver version : 6.5.0
> > > Capabilities : 0xa4201000
> > > Video Capture Multiplanar
> > > Streaming
> > > Extended Pix Format
> > > Device Capabilities
> > > Device Caps : 0x24201000
> > > Video Capture Multiplanar
> > > Streaming
> > > Extended Pix Format
> > > Media Driver Info:
> > > Driver name : mxc-isi
> > > Model : FSL Capture Media Device
> > > Serial :
> > > Bus info : platform:32e00000.isi
> > > Media version : 6.5.0
> > > Hardware revision: 0x00000000 (0)
> > > Driver version : 6.5.0
> > > Interface Info:
> > > ID : 0x0300000c
> > > Type : V4L Video
> > > Entity Info:
> > > ID : 0x0000000a (10)
> > > Name : mxc_isi.0.capture
> > > Function : V4L2 I/O
> > > Pad 0x0100000b : 0: Sink
> > > Link 0x0200000e: from remote pad 0x1000009 of entity
> > > 'mxc_isi.0' (Video Pixel Formatter): Data, Enabled, Immutable
> > > Priority: 2
> > > Video input : 0 (mxc_isi.0.capture: ok)
> > > Format Video Capture Multiplanar:
> > > Width/Height : 640/480
> > > Pixel Format : 'RGGB' (8-bit Bayer RGRG/GBGB)
> > > Field : None
> > > Number of planes : 1
> > > Flags :
> > > Colorspace : sRGB
> > > Transfer Function : sRGB
> > > YCbCr/HSV Encoding: ITU-R 601
> > > Quantization : Limited Range
> > > Plane 0 :
> > > Bytes per Line : 640
> > > Size Image : 307200
> > >
> > > User Controls
> > >
> > > horizontal_flip 0x00980914 (bool) : default=0 value=0
> > > vertical_flip 0x00980915 (bool) : default=0 value=0
> > > alpha_component 0x00980929 (int) : min=0 max=255
> > > step=1 default=0 value=0
> > >
> > > # try to capture a frame
> > > v4l2-ctl --device /dev/video0 --stream-mmap --stream-to=x.raw --stream-count=1
> > > VIDIOC_STREAMON returned -1 (Broken pipe)
> > > ^^^ fails... not sure why
> > >
> > > # try to use gstreamer
> > > gst-launch-1.0 v4l2src device=/dev/video0 !
> > > video/x-bayer,format=rggb,width=640,height=480,framerate=10/1 !
> > > fakesink
> > > Setting pipeline to PAUSED ...
> > > Pipeline is live and does not need PREROLL ...
> > > Pipeline is PREROLLED ...
> > > Setting pipeline to PLAYING ...
> > > New clock: GstSystemClock
> > > ERROR: from element /GstPipeline:pipeline0/GstV4l2Src:v4l2src0: Failed
> > > to allocate required memory.
> > > Additional debug info:
> > > ../sys/v4l2/gstv4l2src.c(759): gst_v4l2src_decide_allocation ():
> > > /GstPipeline:pipeline0/GstV4l2Src:v4l2src0:
> > > Buffer pool activation failed
> > > ERROR: from element /GstPipeline:pipeline0/GstV4l2Src:v4l2src0:
> > > Internal data stream error.
> > > Execution ended after 0:00:00.005517125
> > > Additional debug info:
> > > ../libs/gst/base/gstbasesrc.c(3127): gst_base_src_loop ():
> > > /GstPipeline:pipeline0/GstV4l2Src:v4l2src0:
> > > streaming stopped, reason not-negotiated (-4)
> > > Setting pipeline to NULL ...
> > > Freeing pipeline ...
> > > ^^^ not sure what the memory allocation failure is about. It was
> > > complaining about cma memory until I added cma=256M to the cmdline
> > >
> > > I'm now at the point where I likely need help from the video4linux and
> > > linux-media (cc'd) gurus.
> >
> >
> > The video format from the camera doesn't match the video format
> > through the ISI and the crossbar, so you're getting the broken pipe.
> > My experience with the ISI is that they all need to match since the
> > ISI isn't an ISP.
> > Laurent would likely suggest libcamera, but I haven't used it yet.
> > I'm waiting for the 8MP's ISP driver to get finalized. However, the
> > ISI on the Nano is similar to the ISI on the Plus, so if you want to
> > take a look at the patch I did for the Beacon Nano board, it might
> > give you some ideas on how to set the video formats. The patch I
> > submitted uses a different video format, but I would expect it to work
> > if you change the video format to the RGGB from the IMX219 camera.
> >
> > Hopefully this patch [1] can give you some idea on how to set the
> > video formats for each of the subdevs.
> >
> > adam
> >
> > [1] - https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/arch/arm64/boot/dts/freescale/imx8mn-beacon-baseboard.dtsi?h=v6.5-rc1&id=6bc3ea47332648a4211926ba7afc1e1fb935c71a
> >
>
> Hi Adam,
>
> Thanks, this helped point me in the right direction and proves the
> video capture device works with v4l2.
>
> For the imx219 which can capture 640x480 raw 8bit bayer:
> # configure media entities for 8-bit raw bayer 640x480
> media-ctl -v -V "'imx219 3-0010':0 [fmt:SRGGB8/640x480 field:none]"
> media-ctl -v -V "'crossbar':0 [fmt:SRGGB8/640x480 field:none]"
> media-ctl -v -V "'mxc_isi.0':0 [fmt:SRGGB8/640x480 field:none]"
> # configure for RGGB (8-bit bayer) 640x480
> v4l2-ctl --device /dev/video0
> --set-fmt-video=width=640,height=480,pixelformat=RGGB --verbose
> # capture a frame
> v4l2-ctl --device /dev/video0 --stream-mmap --stream-to=frame.raw
> --stream-count=1
> convert -size 640x480 -depth 8 gray:frame.raw frame.png # convert to png
> # stream to display
> gst-launch-1.0 v4l2src ! \
> video/x-bayer,format=rggb,width=640,height=480,framerate=10/1 ! \
> bayer2rgb ! fbdevsink
>
I would expect if that's all working then libcamera with the ISI
pipeline handler would be able to handle all of the media-ctl
configuration for you.
You should be able to use this directly (without needing calls to media-ctl):
gst-launch-1.0 libcamerasrc ! \
video/x-bayer,format=rggb,width=640,height=480 ! \
bayer2rgb ! fbdevsink
in the same way.
If it does work, I'd be interested to hear that, and if it doesn't -
then lets fix it!
Note I removed the framerate=10/1 as that's the part I would suspect
might cause issues in the libcamerasrc. It's likely worth trying both
with and without it.
Regards
--
Kieran
> best regards,
>
> Tim
>
>
>
> Additional debug info:
> ../libs/gst/base/gstbasesrc.c(3127): gst_base_src_loop ():
> /GstPipeline:pipeline0/GstV4l2Src:v4l2src0:
> streaming stopped, reason not-negotiated (-4)
> Setting pipeline to NULL ...
> Freeing pipeline ...
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
More information about the linux-arm-kernel
mailing list