[PATCH] arm64: dts: imx8mn-var-som-symphony: fix USB OTG

[Hugo Villeneuve]

On Tue, 4 Jul 2023 18:02:53 -0300
Fabio Estevam <festevam at gmail.com> wrote:

> Hi Hugo,
> 
> On Tue, Jul 4, 2023 at 5:41 PM Hugo Villeneuve <hugo at hugovil.com> wrote:
> 
> > Hi Fabio,
> > with interrupts = <11 IRQ_TYPE_LEVEL_LOW>, USB OTG doesn't work.
> 
> PTN5150 datasheet says:
> 
> "Any changes in the attach/detach events or Rp current source changes
> will trigger INTB pin to go LOW."

Hi Fabio,
it is important to remember that on this board, like I explained
before, the INTB pin is not connected to anything.

It is only the ID pin (9) that is connected to the GPIO1_11 pin.

> What about:  interrupts = <11 IRQ_TYPE_EDGE_FALLING>; ?

With this setting, USB OTG works:

$ dmesg | grep 5150
[    4.833529] ptn5150 1-003d: No VBUS GPIO, ignoring VBUS control
[    4.839972] ptn5150 1-003d: DEBUG_IRQ: i2c->irq: 42
[    4.874173] ptn5150 1-003d: DEBUG_IRQ: error in usb_role_switch_get()
[    4.896822] ptn5150 1-003d: No VBUS GPIO, ignoring VBUS control
[    4.902905] ptn5150 1-003d: DEBUG_IRQ: i2c->irq: 42
[    4.911190] ptn5150 1-003d: DEBUG_IRQ: error in usb_role_switch_get()
[    4.918462] ptn5150 1-003d: No VBUS GPIO, ignoring VBUS control
[    4.926197] ptn5150 1-003d: DEBUG_IRQ: i2c->irq: 42
[    4.935210] ptn5150 1-003d: DEBUG_IRQ: error in usb_role_switch_get()
[    4.947673] ptn5150 1-003d: No VBUS GPIO, ignoring VBUS control
[    4.953771] ptn5150 1-003d: DEBUG_IRQ: i2c->irq: 42
[    4.961104] ptn5150 1-003d: DEBUG_IRQ: error in usb_role_switch_get()
[    5.052165] ptn5150 1-003d: No VBUS GPIO, ignoring VBUS control
[    5.058234] ptn5150 1-003d: DEBUG_IRQ: i2c->irq: 42
[    5.064632] ptn5150 1-003d: DEBUG_IRQ: error in usb_role_switch_get()
[    5.096452] ptn5150 1-003d: No VBUS GPIO, ignoring VBUS control
[    5.102578] ptn5150 1-003d: DEBUG_IRQ: i2c->irq: 42
[    5.114959] ptn5150 1-003d: DEBUG_IRQ: error in usb_role_switch_get()
[    5.187060] ptn5150 1-003d: No VBUS GPIO, ignoring VBUS control
[    5.193243] ptn5150 1-003d: DEBUG_IRQ: i2c->irq: 42
[    5.206235] ptn5150 1-003d: DEBUG_IRQ: probe done


> Also, please add a pullup to the GPIO1_11 pad.

There is already an external 10K pull-up resistor (R88) to +3.3V 
on GPIO1_11 pin...

Hugo.