[PATCH] PCI: j721e: Fix delay before PERST# deassert
Bjorn Helgaas
helgaas at kernel.org
Mon Jul 3 09:21:56 PDT 2023
In subject, "Fix" doesn't convey much information. Does it increase?
Decrease? How much time are we talking about? PERST# deassert is at
one end of the delay; what event is at the other end?
Some of these useful bits of information could appear in the subject
line.
On Mon, Jul 03, 2023 at 04:59:14PM +0530, Achal Verma wrote:
> As per the PCIe Card Electromechanical specification REV. 3.0, PERST#
I think the current rev of this spec is r5.0. Can you cite that
instead? I think the relevant section is r5.0, sec 2.9.2.
> signal should be de-asserted after minimum 100ms from the time power-rails
> become stable. Current delay of 100us is observed to be not enough on some
> custom platform implemented using TI's K3 SOCs.
Is this delay for the benefit of the Root Port or for the attached
Endpoint? If the latter, my guess is that some Endpoints might
tolerate the current shorter delay, while others might require more,
and it doesn't sound like "TI's K3 SoC" would be relevant here.
> So, to ensure 100ms delay to give sufficient time for power-rails and
> refclk to become stable, change delay from 100us to 100ms.
>
> From PCIe Card Electromechanical specification REV. 3.0 section 2.6.2:
> TPVPERL: Power stable to PERST# inactive - 100ms
> T-PERST-CLK: REFCLK stable before PERST# inactive - 100 usec.
Numbers like 100ms that come from the PCIe specs should have #defines
for them. If we don't have one already, can you add one, please?
> Fixes: f3e25911a430 ("PCI: j721e: Add TI J721E PCIe driver")
> Signed-off-by: Achal Verma <a-verma1 at ti.com>
> ---
> drivers/pci/controller/cadence/pci-j721e.c | 9 ++++-----
> 1 file changed, 4 insertions(+), 5 deletions(-)
>
> diff --git a/drivers/pci/controller/cadence/pci-j721e.c b/drivers/pci/controller/cadence/pci-j721e.c
> index e70213c9060a..fa2b4c11d2c4 100644
> --- a/drivers/pci/controller/cadence/pci-j721e.c
> +++ b/drivers/pci/controller/cadence/pci-j721e.c
> @@ -499,13 +499,12 @@ static int j721e_pcie_probe(struct platform_device *pdev)
> /*
> * "Power Sequencing and Reset Signal Timings" table in
> * PCI EXPRESS CARD ELECTROMECHANICAL SPECIFICATION, REV. 3.0
> - * indicates PERST# should be deasserted after minimum of 100us
> - * once REFCLK is stable. The REFCLK to the connector in RC
> - * mode is selected while enabling the PHY. So deassert PERST#
> - * after 100 us.
> + * indicates PERST# should be deasserted after minimum of 100ms
> + * after power rails achieve specified operating limits and
> + * within this period reference clock should also become stable.
> */
> if (gpiod) {
> - usleep_range(100, 200);
> + msleep(100);
> gpiod_set_value_cansleep(gpiod, 1);
> }
>
> --
> 2.25.1
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
More information about the linux-arm-kernel
mailing list