[PATCH] arm64: dts: rockchip: add support for Rongpin king3399 board
Krzysztof Kozlowski
krzysztof.kozlowski at linaro.org
Sat Jul 1 02:25:39 PDT 2023
On 30/06/2023 19:27, ocfox wrote:
> king3399 is a bord from Rongpin, you can find detail about
> it here:
> (http://www.rpdzkj.com/copy_2_1703937_175104_2536441.html)
>
> This patch add basic node for the board and make it able to bring
> up.
>
> Works:
> - USB, type-C port
> - Ethernet
> - WiFi/BT
> - HDMI
> - eMMC
> - PCIe
> - sd-card
>
> Not test for other peripheral:
> - AUDIO
> - MIC
> - SIM
> - MIPI
>
> Signed-off-by: ocfox <i at ocfox.me>
> ---
> arch/arm64/boot/dts/rockchip/Makefile | 1 +
> .../boot/dts/rockchip/rk3399-king3399.dts | 1077 +++++++++++++++++
> 2 files changed, 1078 insertions(+)
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-king3399.dts
>
> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> index b7fb908eb92d..73ebee6ef430 100644
> --- a/arch/arm64/boot/dts/rockchip/Makefile
> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> @@ -42,6 +42,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-hugsun-x99.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-khadas-edge.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-khadas-edge-captain.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-khadas-edge-v.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-king3399.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-kobol-helios64.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-leez-p710.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopc-t4.dtb
> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-king3399.dts b/arch/arm64/boot/dts/rockchip/rk3399-king3399.dts
> new file mode 100644
> index 000000000000..5d68add63d59
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3399-king3399.dts
> @@ -0,0 +1,1077 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2017 Fuzhou Rockchip Electronics Co., Ltd.
> + *
> + * Copyright (c) 2023 ocfox <i at ocfox.me>
> + */
> +
> +/dts-v1/;
> +#include <dt-bindings/pwm/pwm.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/usb/pd.h>
> +#include "rk3399.dtsi"
> +#include "rk3399-opp.dtsi"
> +
> +/ {
> + model = "KING3399 RK3399 Board";
> + compatible = "rockchip,king3399", "rockchip,rk3399";
Missing bindings patch. Looks like wrong vendor prefix - you called this
board "Rongpin", not "Rockchip".
> +
> + aliases {
> + mmc0 = &sdio0;
> + mmc1 = &sdmmc;
> + mmc2 = &sdhci;
> + };
> +
> + chosen {
> + stdout-path = "serial2:1500000n8";
> + };
> +
> + clkin_gmac: external-gmac-clock {
> + compatible = "fixed-clock";
> + clock-frequency = <125000000>;
> + clock-output-names = "clkin_gmac";
> + #clock-cells = <0>;
> + };
> +
> + adc-keys {
> + compatible = "adc-keys";
> + io-channels = <&saradc 1>;
> + io-channel-names = "buttons";
> + keyup-threshold-microvolt = <1800000>;
> + poll-interval = <100>;
> +
> + button-up {
> + label = "Volume Up";
> + linux,code = <KEY_VOLUMEUP>;
> + press-threshold-microvolt = <100000>;
> + };
> +
> + button-down {
> + label = "Volume Down";
> + linux,code = <KEY_VOLUMEDOWN>;
> + press-threshold-microvolt = <300000>;
> + };
> +
> + back {
It does not look like you tested the DTS against bindings. Please run
`make dtbs_check` (see
Documentation/devicetree/bindings/writing-schema.rst or
https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/
for instructions).
> + label = "Back";
> + linux,code = <KEY_BACK>;
> + press-threshold-microvolt = <985000>;
> + };
> + };
> +
> + keys: gpio-keys {
> + compatible = "gpio-keys"; // poweroff not sure
> + autorepeat;
> +
> + power {
It does not look like you tested the DTS against bindings. Please run
`make dtbs_check` (see
Documentation/devicetree/bindings/writing-schema.rst or
https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/
for instructions).
> + debounce-interval = <100>;
> + gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
> + label = "GPIO Power";
> + linux,code = <KEY_POWER>;
> + linux,input-type = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pwr_btn>;
> + wakeup-source;
> + };
> + };
> +
> + ir-receiver {
> + compatible = "gpio-ir-receiver";
> + gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_LOW>; // bsp
> + pinctrl-names = "default";
> + pinctrl-0 = <&ir_int>;
> + };
> +
> + backlight: backlight {
> + status = "disabled";
> + compatible = "pwm-backlight";
> + brightness-levels = <
> + 0 1 2 3 4 5 6 7
> + 8 9 10 11 12 13 14 15
> + 16 17 18 19 20 21 22 23
> + 24 25 26 27 28 29 30 31
> + 32 33 34 35 36 37 38 39
> + 40 41 42 43 44 45 46 47
> + 48 49 50 51 52 53 54 55
> + 56 57 58 59 60 61 62 63
> + 64 65 66 67 68 69 70 71
> + 72 73 74 75 76 77 78 79
> + 80 81 82 83 84 85 86 87
> + 88 89 90 91 92 93 94 95
> + 96 97 98 99 100 101 102 103
> + 104 105 106 107 108 109 110 111
> + 112 113 114 115 116 117 118 119
> + 120 121 122 123 124 125 126 127
> + 128 129 130 131 132 133 134 135
> + 136 137 138 139 140 141 142 143
> + 144 145 146 147 148 149 150 151
> + 152 153 154 155 156 157 158 159
> + 160 161 162 163 164 165 166 167
> + 168 169 170 171 172 173 174 175
> + 176 177 178 179 180 181 182 183
> + 184 185 186 187 188 189 190 191
> + 192 193 194 195 196 197 198 199
> + 200 201 202 203 204 205 206 207
> + 208 209 210 211 212 213 214 215
> + 216 217 218 219 220 221 222 223
> + 224 225 226 227 228 229 230 231
> + 232 233 234 235 236 237 238 239
> + 240 241 242 243 244 245 246 247
> + 248 249 250 251 252 253 254 255>;
> + default-brightness-level = <200>;
> + enable-gpios = <&gpio1 RK_PB5 GPIO_ACTIVE_HIGH>;
> + pwms = <&pwm0 0 25000 0>;
> + };
> +
> + sdio_pwrseq: sdio-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + clocks = <&rk808 1>;
> + clock-names = "ext_clock";
> + pinctrl-names = "default";
> + pinctrl-0 = <&wifi_reg_on_h>;
> +
> + reset-gpios = <&gpio0 RK_PB2 GPIO_ACTIVE_LOW>;
> + };
> +
> + /* switched by pmic_sleep */
> + vcc1v8_s3: vcca1v8_s3: vcc1v8-s3 {
Use some consistent name suffixes or prefixes. Some of your regulators
are regulators, some not.
....
> +
> + // vdd 5v: USB 2&3, USB Hub, Type-C, HDMI, MIPI, IR
> + vcc5v0_host: vcc5v0-host-regulator {
Like here
> + compatible = "regulator-fixed";
> + enable-active-high;
> + regulator-boot-on;
> + gpio = <&gpio4 RK_PD6 GPIO_ACTIVE_HIGH>; // bsp
> + pinctrl-names = "default";
> + pinctrl-0 = <&vcc5v0_host_en>;
> + regulator-name = "vcc5v0_host";
> + // regulator-always-on;
Drop dead code
> + vin-supply = <&vcc5v0_sys>;
> + };
> +
> + vcc5v0_typec0: vbus-typec-regulator {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>; // bsp
What is that "// bsp" comment?
> + pinctrl-names = "default";
> + pinctrl-0 = <&vcc5v0_typec_en>;
> + regulator-name = "vcc5v0_typec0";
> + vin-supply = <&vcc5v0_sys>;
> + };
> +
> + vcc_sys: vcc5v0_sys: vcc5v0-sys { // bsp
> + compatible = "regulator-fixed";
> + regulator-name = "vcc5v0_sys";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&dc_12v>;
> + };
> +
> +
> + dc_12v: vdd_12v: dc-12v { // dc_12v vdd_12V
> + compatible = "regulator-fixed";
> + regulator-name = "dc_12v";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <12000000>;
> + regulator-max-microvolt = <12000000>;
> + };
> +
> + rt5651-sound { // verify
So it is not suitable to upstream. Drop unrelated comments or mark your
patch as not for merging.
> + status = "okay";
Drop, it's by default.
> + compatible = "simple-audio-card";
> + pinctrl-names = "default";
> + pinctrl-0 = <&hp_det>;
> +
> + simple-audio-card,name = "realtek,rt5651-codec";
> + simple-audio-card,format = "i2s";
> + simple-audio-card,mclk-fs = <256>;
> + simple-audio-card,hp-det-gpio = <&gpio4 RK_PD4 GPIO_ACTIVE_HIGH>;
> + simple-audio-card,aux-devs = <&speaker_amp>;
> + simple-audio-card,pin-switches = "Speaker";
> + simple-audio-card,widgets =
> + "Microphone", "Mic Jack",
> + "Headphone", "Headphones",
> + "Speaker", "Speaker";
> + simple-audio-card,routing =
> + "Mic Jack", "micbias1",
> + "Headphones", "HPOL",
> + "Headphones", "HPOR",
> + "Speaker Amplifier INL", "HPOL",
> + "Speaker Amplifier INR", "HPOR",
> + "Speaker", "Speaker Amplifier OUTL",
> + "Speaker", "Speaker Amplifier OUTR";
> + simple-audio-card,cpu {
> + sound-dai = <&i2s0>;
> + };
> + simple-audio-card,codec {
> + sound-dai = <&rt5651>;
> + };
> + };
> +
> + speaker_amp: speaker-amplifier { // verify
> + compatible = "simple-audio-amplifier";
> + pinctrl-names = "default";
> + pinctrl-0 = <&spk_ctl>;
> + enable-gpios = <&gpio0 RK_PB3 GPIO_ACTIVE_HIGH>;
> + sound-name-prefix = "Speaker Amplifier";
> + vcc-supply = <&vcc5v0_sys>;
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&breathe_led_pin>;
> +
> + breathe_led: led-breathe-led { // bsp // vdd_12V
> + label = "breathe_led";
> + linux,default-trigger = "heartbeat";
> + default-state = "off";
> + gpios = <&gpio4 RK_PD0 GPIO_ACTIVE_LOW>;
> + };
> + };
> +
> + fan0: gpio-fan { // verify // vcc5v0_sys
> + #cooling-cells = <2>;
> + compatible = "gpio-fan";
> + gpio-fan,speed-map = <0 0 3000 1>;
> + gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_HIGH>;
> + status = "okay";
> + };
Drop
> +
> + gpio-restart {
> + compatible = "gpio-restart";
> + gpios = <&gpio1 RK_PD0 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&hub_rst>;
> + priority = <200>;
> + active-delay = <100>;
> + inactive-delay = <10>;
> + wait-delay = <100>;
> + };
> +
Drop stray blank line
...
> +
> +&i2c1 {
> + i2c-scl-rising-time-ns = <300>;
> + i2c-scl-falling-time-ns = <15>;
> + status = "okay";
> +
> + rt5651: rt5651 at 1a {
Node names should be generic. See also explanation and list of examples
in DT specification:
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
> + #sound-dai-cells = <0>;
> + compatible = "realtek,rt5651";
> + reg = <0x1a>;
> + clocks = <&cru SCLK_I2S_8CH_OUT>;
> + clock-names = "mclk";
> + status = "okay";
> + };
> +};
> +
> +&i2c2 {
> + status = "okay";
> +};
> +
> +// Used for HDMI
> +&i2c3 {
> + i2c-scl-rising-time-ns = <450>;
> + i2c-scl-falling-time-ns = <15>;
> + status = "okay";
> +};
> +
> +// Type-C
> +// Accelerometer
> +// Touch Screen
> +&i2c4 {
> + clock-frequency = <400000>;
> + i2c-scl-rising-time-ns = <450>;
> + i2c-scl-falling-time-ns = <15>;
> + status = "okay";
> +
> + fusb302 at 22 { // bsp checked
Node names should be generic. See also explanation and list of examples
in DT specification:
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
Best regards,
Krzysztof
More information about the linux-arm-kernel
mailing list