[PATCH v4 3/5] iommu/arm-smmu: add ACTLR data and support for SM8550

[Bibek Kumar Patro]

On 12/16/2023 5:33 AM, Konrad Dybcio wrote:
> On 15.12.2023 13:54, Robin Murphy wrote:
>> On 2023-12-15 12:20 pm, Bibek Kumar Patro wrote:
>>>
>>>
>>> On 12/15/2023 4:14 PM, Dmitry Baryshkov wrote:
>>>> On Fri, 15 Dec 2023 at 12:19, Bibek Kumar Patro
>>>> <quic_bibekkum at quicinc.com> wrote:
>>>>>
>>>>> Add ACTLR data table for SM8550 along with support for
>>>>> same including SM8550 specific implementation operations.
>>>>>
>>>>> Signed-off-by: Bibek Kumar Patro <quic_bibekkum at quicinc.com>
>>>>> ---
>>>>>    drivers/iommu/arm/arm-smmu/arm-smmu-qcom.c | 89 ++++++++++++++++++++++
>>>>>    1 file changed, 89 insertions(+)
>>>>>
>>>>> diff --git a/drivers/iommu/arm/arm-smmu/arm-smmu-qcom.c b/drivers/iommu/arm/arm-smmu/arm-smmu-qcom.c
>>>>> index cb49291f5233..d2006f610243 100644
>>>>> --- a/drivers/iommu/arm/arm-smmu/arm-smmu-qcom.c
>>>>> +++ b/drivers/iommu/arm/arm-smmu/arm-smmu-qcom.c
>>>>> @@ -20,6 +20,85 @@ struct actlr_config {
>>>>>           u32 actlr;
>>>>>    };
>>>>>
>>>>> +/*
>>>>> + * SMMU-500 TRM defines BIT(0) as CMTLB (Enable context caching in the
>>>>> + * macro TLB) and BIT(1) as CPRE (Enable context caching in the prefetch
>>>>> + * buffer). The remaining bits are implementation defined and vary across
>>>>> + * SoCs.
>>>>> + */
>>>>> +
>>>>> +#define PREFETCH_DEFAULT       0
>>>>> +#define PREFETCH_SHALLOW       BIT(8)
>>>>> +#define PREFETCH_MODERATE      BIT(9)
>>>>> +#define PREFETCH_DEEP          (BIT(9) | BIT(8))
>>>>
>>>> I thin the following might be more correct:
>>>>
>>>> #include <linux/bitfield.h>
>>>>
>>>> #define PREFETCH_MASK GENMASK(9, 8)
>>>> #define PREFETCH_DEFAULT FIELD_PREP(PREFETCH_MASK, 0)
>>>> #define PREFETCH_SHALLOW FIELD_PREP(PREFETCH_MASK, 1)
>>>> #define PREFETCH_MODERATE FIELD_PREP(PREFETCH_MASK, 2)
>>>> #define PREFETCH_DEEP FIELD_PREP(PREFETCH_MASK, 3)
>>>>
>>>
>>> Ack, thanks for this suggestion. Let me try this out using
>>> GENMASK. Once tested, will take care of this in next version.
>>
>> FWIW the more typical usage would be to just define the named macros for the raw field values, then put the FIELD_PREP() at the point of use. However in this case that's liable to get pretty verbose, so although I'm usually a fan of bitfield.h, the most readable option here might actually be to stick with simpler definitions of "(0 << 8)", "(1 << 8)", etc. However it's not really a big deal either way, and I defer to whatever Dmitry and Konrad prefer, since they're the ones looking after arm-smmu-qcom the most :)
> My 5 cents would be to just use the "common" style of doing this, so:
> 
> #define ACTRL_PREFETCH	GENMASK(9, 8)
>   #define PREFETCH_DEFAULT 0
>   #define PREFETCH_SHALLOW 1
>   #define PREFETCH_MODERATE 2
>   #define PREFETCH_DEEP 3
> 
> and then use
> 
> | FIELD_PREP(ACTRL_PREFETCH, PREFETCH_x)
> 
> it can get verbose, but.. arguably that's good, since you really want
> to make sure the right bits are set here
> 

Thanks for the suggestion with these mods.
Let me try out the suggested way and once tested will post this in next
version.

Thanks,
Bibek

> Konrad