[PATCH v9 5/7] arm64: dts: ti: k3-am69-sk: Add support for TPS6594 PMIC

[Neha Malcom Francis]

Hi Udit,

On 07/12/23 10:29, Kumar, Udit wrote:
> 
> On 12/5/2023 3:04 PM, Neha Malcom Francis wrote:
>> This patch adds support for TPS6594 PMIC on wkup I2C0 bus. This device
>> provides regulators (bucks and LDOs), but also GPIOs, a RTC, a watchdog,
>> an ESM (Error Signal Monitor) which monitors the SoC error output
>> signal, and a PFSM (Pre-configurable Finite State Machine) which manages
>> the operational modes of the PMIC.
>>
>> Signed-off-by: Neha Malcom Francis <n-francis at ti.com>
>> Tested-by: Manorit Chawdhry <m-chawdhry at ti.com>
>> ---
>>   arch/arm64/boot/dts/ti/k3-am69-sk.dts | 100 ++++++++++++++++++++++++++
>>   1 file changed, 100 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/ti/k3-am69-sk.dts 
>> b/arch/arm64/boot/dts/ti/k3-am69-sk.dts
>> index 9868c7049bfb..dec27acb4e96 100644
>> --- a/arch/arm64/boot/dts/ti/k3-am69-sk.dts
>> +++ b/arch/arm64/boot/dts/ti/k3-am69-sk.dts
>> @@ -431,6 +431,17 @@ J784S4_IOPAD(0x000, PIN_INPUT, 7) /* (AN35) 
>> EXTINTN.GPIO0_0 */
>>       };
>>   };
>> +&wkup_pmx1 {
>> +    status = "okay";
>> +
>> +    pmic_irq_pins_default: pmic-irq-default-pins {
>> +        pinctrl-single,pins = <
>> +            /* (AA37) MCU_ADC1_AIN4.WKUP_GPIO0_83 */
>> +            J784S4_WKUP_IOPAD(0x12c, PIN_INPUT, 7)
>> +        >;
>> +    };
>> +};
> 
> Could you re check this pin mux
> 
> wkup_pmx1 is defined as reg = <0x00 0x4301c038 0x00 0x02c>;
> 
> LTM, this is above wrt given size
> 

You're right it must be in wkup_pmx2. Thanks for catching this!

> 
>> +
>>   &wkup_pmx2 {
>>       bootph-all;
>>       wkup_uart0_pins_default: wkup-uart0-default-pins {
>> @@ -631,6 +642,95 @@ eeprom at 51 {
>>           compatible = "atmel,24c512";
>>           reg = <0x51>;
>>       };
>> +
>> +    tps659413: pmic at 48 {
>> +        compatible = "ti,tps6594-q1";
>> +        reg = <0x48>;
>> +        system-power-controller;
>> +        pinctrl-names = "default";
>> +        pinctrl-0 = <&pmic_irq_pins_default>;
>> +        interrupt-parent = <&wkup_gpio0>;
>> +        interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
>> +        ti,primary-pmic;
>> +
>> +        gpio-controller;
>> +        #gpio-cells = <2>;
>> +
>> +        buck12-supply = <&vsys_3v3>;
>> +        buck3-supply = <&vsys_3v3>;
>> +        buck4-supply = <&vsys_3v3>;
>> +        buck5-supply = <&vsys_3v3>;
>> +        ldo1-supply = <&vsys_3v3>;
>> +        ldo2-supply = <&vsys_3v3>;
>> +        ldo3-supply = <&vsys_3v3>;
>> +        ldo4-supply = <&vsys_3v3>;
>> +
>> +        regulators {
>> +            bucka12: buck12 {
>> +                regulator-name = "vdd_ddr_1v1";
>> +                regulator-min-microvolt = <1100000>;
>> +                regulator-max-microvolt = <1100000>;
>> +                regulator-boot-on;
>> +                regulator-always-on;
>> +            };
>> +
>> +            bucka3: buck3 {
>> +                regulator-name = "vdd_ram_0v85";
>> +                regulator-min-microvolt = <850000>;
>> +                regulator-max-microvolt = <850000>;
>> +                regulator-boot-on;
>> +                regulator-always-on;
>> +            };
>> +
>> +            bucka4: buck4 {
>> +                regulator-name = "vdd_io_1v8";
>> +                regulator-min-microvolt = <1800000>;
>> +                regulator-max-microvolt = <1800000>;
>> +                regulator-boot-on;
>> +                regulator-always-on;
>> +            };
>> +
>> +            bucka5: buck5 {
>> +                regulator-name = "vdd_mcu_0v85";
>> +                regulator-min-microvolt = <850000>;
>> +                regulator-max-microvolt = <850000>;
>> +                regulator-boot-on;
>> +                regulator-always-on;
>> +            };
>> +
>> +            ldoa1: ldo1 {
>> +                regulator-name = "vdd_mcuio_1v8";
>> +                regulator-min-microvolt = <1800000>;
>> +                regulator-max-microvolt = <1800000>;
>> +                regulator-boot-on;
>> +                regulator-always-on;
>> +            };
>> +
>> +            ldoa2: ldo2 {
>> +                regulator-name = "vdd_mcuio_3v3";
>> +                regulator-min-microvolt = <3300000>;
>> +                regulator-max-microvolt = <3300000>;
>> +                regulator-boot-on;
>> +                regulator-always-on;
>> +            };
>> +
>> +            ldoa3: ldo3 {
>> +                regulator-name = "vds_dll_0v8";
>> +                regulator-min-microvolt = <800000>;
>> +                regulator-max-microvolt = <800000>;
>> +                regulator-boot-on;
>> +                regulator-always-on;
>> +            };
>> +
>> +            ldoa4: ldo4 {
>> +                regulator-name = "vda_mcu_1v8";
>> +                regulator-min-microvolt = <1800000>;
>> +                regulator-max-microvolt = <1800000>;
>> +                regulator-boot-on;
>> +                regulator-always-on;
>> +            };
>> +        };
>> +    };
>>   };
>>   &wkup_gpio0 {

-- 
Thanking You
Neha Malcom Francis