[PATCH v5 14/20] pinctrl: samsung: Add gs101 SoC pinctrl configuration

[Sam Protsenko]

On Fri, Dec 1, 2023 at 7:37 PM Alim Akhtar <alim.akhtar at samsung.com> wrote:
>
>
>
> > -----Original Message-----
> > From: Sam Protsenko <semen.protsenko at linaro.org>
> > Sent: Saturday, December 2, 2023 6:10 AM
> > To: Peter Griffin <peter.griffin at linaro.org>
> > Cc: robh+dt at kernel.org; krzysztof.kozlowski+dt at linaro.org;
> > mturquette at baylibre.com; conor+dt at kernel.org; sboyd at kernel.org;
> > tomasz.figa at gmail.com; s.nawrocki at samsung.com; linus.walleij at linaro.org;
> > wim at linux-watchdog.org; linux at roeck-us.net; catalin.marinas at arm.com;
> > will at kernel.org; arnd at arndb.de; olof at lixom.net;
> > gregkh at linuxfoundation.org; jirislaby at kernel.org;
> > cw00.choi at samsung.com; alim.akhtar at samsung.com;
> > tudor.ambarus at linaro.org; andre.draszik at linaro.org;
> > saravanak at google.com; willmcvicker at google.com; soc at kernel.org;
> > devicetree at vger.kernel.org; linux-arm-kernel at lists.infradead.org; linux-
> > samsung-soc at vger.kernel.org; linux-clk at vger.kernel.org; linux-
> > gpio at vger.kernel.org; linux-watchdog at vger.kernel.org; kernel-
> > team at android.com; linux-serial at vger.kernel.org
> > Subject: Re: [PATCH v5 14/20] pinctrl: samsung: Add gs101 SoC pinctrl
> > configuration
> >
> > On Fri, Dec 1, 2023 at 10:11 AM Peter Griffin <peter.griffin at linaro.org>
> > wrote:
> > >
> > > Add support for the pin-controller found on the gs101 SoC used in
> > > Pixel 6 phones.
> > >
> > > Signed-off-by: Peter Griffin <peter.griffin at linaro.org>
> > > ---
> > >  .../pinctrl/samsung/pinctrl-exynos-arm64.c    | 159 ++++++++++++++++++
> > >  drivers/pinctrl/samsung/pinctrl-exynos.c      |   2 +
> > >  drivers/pinctrl/samsung/pinctrl-exynos.h      |  34 ++++
> > >  drivers/pinctrl/samsung/pinctrl-samsung.c     |   2 +
> > >  drivers/pinctrl/samsung/pinctrl-samsung.h     |   1 +
> > >  5 files changed, 198 insertions(+)
> > >
> > > diff --git a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c
> > > b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c
> > > index cb965cf93705..e1a0668ecb16 100644
> > > --- a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c
> > > +++ b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c
> > > @@ -796,3 +796,162 @@ const struct samsung_pinctrl_of_match_data
> > fsd_of_data __initconst = {
> > >         .ctrl           = fsd_pin_ctrl,
> > >         .num_ctrl       = ARRAY_SIZE(fsd_pin_ctrl),
> > >  };
> > > +
> > > +/*
> > > + * bank type for non-alive type
> > > + * (CON bit field: 4, DAT bit field: 1, PUD bit field: 4, DRV bit
> > > +field: 4)
> > > + * (CONPDN bit field: 2, PUDPDN bit field: 4)  */ static struct
> > > +samsung_pin_bank_type gs101_bank_type_off  = {
> > > +       .fld_width = { 4, 1, 4, 4, 2, 4, },
> > > +       .reg_offset = { 0x00, 0x04, 0x08, 0x0c, 0x10, 0x14, }, };
> >
> > This is just the same as exynos850_bank_type_off (100% duplication).
> > Here is what I suggest. Now that it's obvious there is some common platform
> > for moder Exynos SoCs, and it's probably Exynos9, I'd suggest next course of
> > action (if maintainers agree):
> >   1. Remove this one
> >   2. Rename exynos850_bank_type_off to exynos9_bank_type_off
> >   3. Use it for both gs101 and exynos850
> >
> > Does it make sense?
> >
> My opinion is to reuse exynos850 for gs101 (wherever applicable), same philosophy was historically followed in this file.
> That way (using exynos850 for gs101) things will be simple.
> Adding exynos9_* is not adding any benefit, rather it create confusion.
>

Yes. But why not also rename exynos850_* to exynos9_*? I've a feeling
that a lot of modern Exynos SoCs have the same pin bank configuration.
Wouldn't it be better to use exynos9_ prefix for all such SoCs than
exynos850_*? Because Exynos9 is a family, but Exynos850 is a
particular SoC from that family.

> > > +
> > > +/*
> > > + * bank type for alive type
> > > + * (CON bit field: 4, DAT bit field: 1, PUD bit field: 4, DRV bit
> > > +field: 4)  */ static const struct samsung_pin_bank_type
> > > +gs101_bank_type_alive = {
> > > +       .fld_width = { 4, 1, 4, 4, },
> > > +       .reg_offset = { 0x00, 0x04, 0x08, 0x0c, }, };
> [...]
>
>