[PATCH 3/3] arm64: dts: rockchip: Add Orange Pi 5
Muhammed Efe Cetin
efectn at 6tel.net
Thu Aug 17 06:33:55 PDT 2023
Hi, Ondřej
Thanks for reviews, i'll fix them soon.
On 15.08.2023 19:39, Ondřej Jirman wrote:
> Hello Muhammed,
>
> Looks like you trusted Xunlong's DT a bit too much. See a few issues
> below.
>
> On Tue, Aug 15, 2023 at 03:59:01PM +0300, Muhammed Efe Cetin wrote:
>> ing-List: linux-kernel at vger.kernel.org
>>
>> Add initial support for OPi5 that includes support for USB2, PCIe2, Sata,
>> Sdmmc, SPI Flash, PMIC.
>>
>> Signed-off-by: Muhammed Efe Cetin <efectn at 6tel.net>
>> ---
>> .../boot/dts/rockchip/rk3588s-orangepi-5.dts | 873 ++++++++++++++++++
>> 1 file changed, 873 insertions(+)
>> create mode 100644 arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5.dts
>>
>> diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5.dts b/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5.dts
>> new file mode 100644
>> index 000000000000..85071084a207
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5.dts
>> @@ -0,0 +1,873 @@
>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>> +
>> +/dts-v1/;
>> +
>> +#include <dt-bindings/pinctrl/rockchip.h>
>> +#include <dt-bindings/gpio/gpio.h>
>> +#include <dt-bindings/input/input.h>
>> +#include "rk3588s.dtsi"
>> +
>> +/ {
>> + model = "Xunlong Orange Pi 5";
>> + compatible = "xunlong,orangepi-5", "rockchip,rk3588s";
>> +
>> + aliases {
>> + mmc0 = &sdmmc;
>> +
>> + serial2 = &uart2;
>> + };
>> +
>> + chosen {
>> + stdout-path = "serial2:1500000n8";
>> + };
>> +
>> + leds {
>> + compatible = "gpio-leds";
>> + pinctrl-names = "default";
>> + pinctrl-0 =<&leds_gpio>;
>> +
>> + led at 1 {
>> + gpios = <&gpio1 RK_PA2 GPIO_ACTIVE_HIGH>;
>> + label = "status_led";
>> + linux,default-trigger = "heartbeat";
>> + linux,default-trigger-delay-ms = <0>;
>
> This is a PWM LED hooked to PWM0_M2. You can use a PWM LED drvier.
Yes the mosfet is connected to PWM line. I'll try to use pwm-leds here.
>
>> + };
>> + };
>> +
>> + adc-keys {
>> + compatible = "adc-keys";
>> + io-channels = <&saradc 1>;
>> + io-channel-names = "buttons";
>> + keyup-threshold-microvolt = <1800000>;
>> + poll-interval = <100>;
>> +
>> + vol-up-key {
>> + label = "volume up";
>> + linux,code = <KEY_VOLUMEUP>;
>> + press-threshold-microvolt = <17000>;
>> + };
>> +
>> + vol-down-key {
>> + label = "volume down";
>> + linux,code = <KEY_VOLUMEDOWN>;
>> + press-threshold-microvolt = <417000>;
>> + };
>> +
>> + menu-key {
>> + label = "menu";
>> + linux,code = <KEY_MENU>;
>> + press-threshold-microvolt = <890000>;
>> + };
>> +
>> + back-key {
>> + label = "back";
>> + linux,code = <KEY_BACK>;
>> + press-threshold-microvolt = <1235000>;
>
> None of these 4 buttons are in the scehmatic. There's one recovery button hooked
> to saradc 0, instead.
Will remove these too. I won't add recovery button because of it's mostly used for rockusb.
>
>> + };
>> + };
>> +
>> + backlight: backlight {
>> + compatible = "pwm-backlight";
>> + brightness-levels = < 0 20 20 21 21 22 22 23
>> + 23 24 24 25 25 26 26 27
>> + 27 28 28 29 29 30 30 31
>> + 31 32 32 33 33 34 34 35
>> + 35 36 36 37 37 38 38 39
>> + 40 41 42 43 44 45 46 47
>> + 48 49 50 51 52 53 54 55
>> + 56 57 58 59 60 61 62 63
>> + 64 65 66 67 68 69 70 71
>> + 72 73 74 75 76 77 78 79
>> + 80 81 82 83 84 85 86 87
>> + 88 89 90 91 92 93 94 95
>> + 96 97 98 99 100 101 102 103
>> + 104 105 106 107 108 109 110 111
>> + 112 113 114 115 116 117 118 119
>> + 120 121 122 123 124 125 126 127
>> + 128 129 130 131 132 133 134 135
>> + 136 137 138 139 140 141 142 143
>> + 144 145 146 147 148 149 150 151
>> + 152 153 154 155 156 157 158 159
>> + 160 161 162 163 164 165 166 167
>> + 168 169 170 171 172 173 174 175
>> + 176 177 178 179 180 181 182 183
>> + 184 185 186 187 188 189 190 191
>> + 192 193 194 195 196 197 198 199
>> + 200 201 202 203 204 205 206 207
>> + 208 209 210 211 212 213 214 215
>> + 216 217 218 219 220 221 222 223
>> + 224 225 226 227 228 229 230 231
>> + 232 233 234 235 236 237 238 239
>> + 240 241 242 243 244 245 246 247
>> + 248 249 250 251 252 253 254 255>;
>
> Linar table will not give you "linear" looking brightness steps. Use some
> algorithm to generate a proper curve of PWM duty cycle -> brightness table.
>
> Either way, the board has no backlight. This should be in overlay if someone
> wants to connect some particular display to the board.
You are right. It's better idea to use them in overlay instead of making them a part of devicetree.
>
>> + default-brightness-level = <200>;
>> + pwms = <&pwm2 0 25000 0>;
>> + };
>> +
>> + backlight_1: backlight_1 {
>> + compatible = "pwm-backlight";
>> + brightness-levels = < 0 20 20 21 21 22 22 23
>> + 23 24 24 25 25 26 26 27
>> + 27 28 28 29 29 30 30 31
>> + 31 32 32 33 33 34 34 35
>> + 35 36 36 37 37 38 38 39
>> + 40 41 42 43 44 45 46 47
>> + 48 49 50 51 52 53 54 55
>> + 56 57 58 59 60 61 62 63
>> + 64 65 66 67 68 69 70 71
>> + 72 73 74 75 76 77 78 79
>> + 80 81 82 83 84 85 86 87
>> + 88 89 90 91 92 93 94 95
>> + 96 97 98 99 100 101 102 103
>> + 104 105 106 107 108 109 110 111
>> + 112 113 114 115 116 117 118 119
>> + 120 121 122 123 124 125 126 127
>> + 128 129 130 131 132 133 134 135
>> + 136 137 138 139 140 141 142 143
>> + 144 145 146 147 148 149 150 151
>> + 152 153 154 155 156 157 158 159
>> + 160 161 162 163 164 165 166 167
>> + 168 169 170 171 172 173 174 175
>> + 176 177 178 179 180 181 182 183
>> + 184 185 186 187 188 189 190 191
>> + 192 193 194 195 196 197 198 199
>> + 200 201 202 203 204 205 206 207
>> + 208 209 210 211 212 213 214 215
>> + 216 217 218 219 220 221 222 223
>> + 224 225 226 227 228 229 230 231
>> + 232 233 234 235 236 237 238 239
>> + 240 241 242 243 244 245 246 247
>> + 248 249 250 251 252 253 254 255>;
>> + default-brightness-level = <200>;
>> + pwms = <&pwm6 0 25000 0>;
>> + };
>
> Ditto.
>
>> + vcc12v_dcin: vcc12v-dcin-regulator {
>> + compatible = "regulator-fixed";
>> + regulator-name = "vcc12v_dcin";
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <12000000>;
>> + regulator-max-microvolt = <12000000>;
>> + };
>
> The board has no 12V input. Please avoid low-effort copy pasting from vendor's
> device tree. Check everything with the schematic to verify DT is actually
> describing the HW correctly, if you really want to start from the vendor's DT
> when porting the board to mainline Linux.
Thanks i'll remove it.
>
>> + vcc5v0_sys: vcc5v0-sys-regulator {
>> + compatible = "regulator-fixed";
>> + regulator-name = "vcc5v0_sys";
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <5000000>;
>> + regulator-max-microvolt = <5000000>;
>> + vin-supply = <&vcc12v_dcin>;
>> + };
>
> Not supplied from 12V power supply.
>
>> + vcc_1v1_nldo_s3: vcc-1v1-nldo-s3-regulator {
>> + compatible = "regulator-fixed";
>> + regulator-name = "vcc_1v1_nldo_s3";
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <1100000>;
>> + regulator-max-microvolt = <1100000>;
>> + vin-supply = <&vcc5v0_sys>;
>> + };
>
> There's no such regulator on the board.
It's connected to PMIC https://i.imgur.com/sVJdC5K.png
>
>> + vcc_3v3_sd_s0: vcc-3v3-sd-s0-regulator {
>> + compatible = "regulator-fixed";
>> + regulator-name = "vcc_3v3_sd_s0";
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + gpios = <&gpio4 RK_PB5 GPIO_ACTIVE_LOW>;
>> + enable-active-low;
>> + vin-supply = <&vcc_3v3_s3>;
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + };
>
> Fixed regulators don't implement regulator-state-*. Also why are you making
> this regulator always on? It will be impossible for mmc subsystem to power
> cycle the SD card. (without knowing, which is bad, because after powercycle
> it will think that uSD I/O is in 3.3V, while it may still be in 1.8V mode)
I'll remove regulator-always-on and regulator-state-mem.
>
>> + };
>>
>> + vcc5v0_usbdcin: vcc5v0-usbdcin-regulator {
>> + compatible = "regulator-fixed";
>> + regulator-name = "vcc5v0_usbdcin";
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <5000000>;
>> + regulator-max-microvolt = <5000000>;
>> + vin-supply = <&vcc12v_dcin>;
>> + };
>
> No such regulator on the board.
Will remove it.
>
>> + vcc5v0_usb: vcc5v0-usb-regulator {
>> + compatible = "regulator-fixed";
>> + regulator-name = "vcc5v0_usb";
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <5000000>;
>> + regulator-max-microvolt = <5000000>;
>> + vin-supply = <&vcc5v0_usbdcin>;
>> + };
>
> No such regulator on the board. Host ports' VBUS is either hardwired
> to VCC_5V0 or goes throug a a protection circuit and becomes VCC5V0_USB_HOST.
Will remove it.
>
>> + vbus5v0_typec: vbus5v0-typec-regulator {
>> + compatible = "regulator-fixed";
>> + regulator-name = "vbus5v0_typec";
>> + regulator-min-microvolt = <5000000>;
>> + regulator-max-microvolt = <5000000>;
>> + enable-active-high;
>> + gpio = <&gpio3 RK_PC0 GPIO_ACTIVE_HIGH>;
>> + vin-supply = <&vcc5v0_usb>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&typec5v_pwren>;
>> + };
>
> No such power rail on the board. This should be VBUS_TYPEC power rail.
> Please name regulators/power rails as they are named in the schematic.
> Otherwise it's impossible to cross-check DT against schematic.
Perhaps i can add it as a comment line. Otherwise the current name seems OK to me but still open to suggestions.
>
>> + combophy_avdd0v85: combophy-avdd0v85-regulator {
>> + compatible = "regulator-fixed";
>> + regulator-name = "combophy_avdd0v85";
>> + regulator-boot-on;
>> + regulator-always-on;
>> + regulator-min-microvolt = <850000>;
>> + regulator-max-microvolt = <850000>;
>> + vin-supply = <&vdd_0v85_s0>;
>> + };
>
> No such regulator on the board.
Will remove it.
>
>> + combophy_avdd1v8: combophy-avdd1v8-regulator {
>> + compatible = "regulator-fixed";
>> + regulator-name = "combophy_avdd1v8";
>> + regulator-boot-on;
>> + regulator-always-on;
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + vin-supply = <&avcc_1v8_s0>;
>> + };
>
> Again, no such regulator on the board.
Will remove it.
>
>> +
>> + vcc3v3_pcie2x1l2: vcc3v3-pcie2x1l2-regulator {
>> + compatible = "regulator-fixed";
>> + regulator-name = "vcc3v3_pcie2x1l2";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + enable-active-high;
>> + regulator-boot-on;
>> + regulator-always-on;
>> + gpios = <&gpio0 RK_PC5 GPIO_ACTIVE_HIGH>;
>> + startup-delay-us = <50000>;
>
> Startup delay for always-on regulator is kinda pointless. Also why is this
> always on? It should not be.
Agree, i'll remove regulator-always-on property.
>
>> + vin-supply = <&vcc5v0_sys>;
>> + };
>
> No such regulator on the board. You might have meant VCC3V3_PCIE30,
> or not?
Yes. However their naming in schematics is pretty nonsense. The board doesn't have PCIe3, i think current naming is more appropriate.
>
>> +};
>> +
>> +&combphy0_ps {
>> + status = "okay";
>> +};
>> +
>> +&combphy2_psu {
>> + status = "okay";
>> +};
>> +
>> +&cpu_b0 {
>> + cpu-supply = <&vdd_cpu_big0_s0>;
>> + mem-supply = <&vdd_cpu_big0_mem_s0>;
>> +};
>> +
>> +&cpu_b1 {
>> + cpu-supply = <&vdd_cpu_big0_s0>;
>> + mem-supply = <&vdd_cpu_big0_mem_s0>;
>> +};
>> +
>> +&cpu_b2 {
>> + cpu-supply = <&vdd_cpu_big1_s0>;
>> + mem-supply = <&vdd_cpu_big1_mem_s0>;
>> +};
>> +
>> +&cpu_b3 {
>> + cpu-supply = <&vdd_cpu_big1_s0>;
>> + mem-supply = <&vdd_cpu_big1_mem_s0>;
>> +};
>> +
>> +&cpu_l0 {
>> + cpu-supply = <&vdd_cpu_lit_s0>;
>> + mem-supply = <&vdd_cpu_lit_mem_s0>;
>> +};
>> +
>> +&cpu_l1 {
>> + cpu-supply = <&vdd_cpu_lit_s0>;
>> + mem-supply = <&vdd_cpu_lit_mem_s0>;
>> +};
>> +
>> +&cpu_l2 {
>> + cpu-supply = <&vdd_cpu_lit_s0>;
>> + mem-supply = <&vdd_cpu_lit_mem_s0>;
>> +};
>> +
>> +&cpu_l3 {
>> + cpu-supply = <&vdd_cpu_lit_s0>;
>> + mem-supply = <&vdd_cpu_lit_mem_s0>;
>> +};
>> +
>> +&gmac1 {
>> + clock_in_out = "output";
>> + phy-handle = <&rgmii_phy1>;
>> + phy-mode = "rgmii-rxid";
>> + pinctrl-0 = <&gmac1_miim
>> + &gmac1_tx_bus2
>> + &gmac1_rx_bus2
>> + &gmac1_rgmii_clk
>> + &gmac1_rgmii_bus>;
>> + pinctrl-names = "default";
>> + snps,reset-gpio = <&gpio3 RK_PB2 GPIO_ACTIVE_LOW>;
>> + snps,reset-active-low;
>> + snps,reset-delays-us = <0 20000 100000>;
>> + tx_delay = <0x42>;
>> + status = "okay";
>> +};
>> +
>> +&i2c0 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&i2c0m2_xfer>;
>> + status = "okay";
>> +
>> + vdd_cpu_big0_s0: vdd_cpu_big0_mem_s0: regulator at 42 {
>> + compatible = "rockchip,rk8602";
>> + reg = <0x42>;
>> + fcs,suspend-voltage-selector = <1>;
>> + regulator-name = "vdd_cpu_big0_s0";
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <550000>;
>> + regulator-max-microvolt = <1050000>;
>> + regulator-ramp-delay = <2300>;
>> + vin-supply = <&vcc5v0_sys>;
>> +
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + vdd_cpu_big1_s0: vdd_cpu_big1_mem_s0: regulator at 43 {
>> + compatible = "rockchip,rk8603", "rockchip,rk8602";
>> + reg = <0x43>;
>> + fcs,suspend-voltage-selector = <1>;
>> + regulator-name = "vdd_cpu_big1_s0";
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <550000>;
>> + regulator-max-microvolt = <1050000>;
>> + regulator-ramp-delay = <2300>;
>> + vin-supply = <&vcc5v0_sys>;
>> +
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +};
>> +
>> +&i2c2 {
>> + status = "okay";
>> +
>> + vdd_npu_s0: vdd_npu_mem_s0: regulator at 42 {
>> + compatible = "rockchip,rk8602";
>> + reg = <0x42>;
>> + fcs,suspend-voltage-selector = <1>;
>> + regulator-name = "vdd_npu_s0";
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <550000>;
>> + regulator-max-microvolt = <950000>;
>> + regulator-ramp-delay = <2300>;
>> + vin-supply = <&vcc5v0_sys>;
>> +
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +};
>> +
>> +&i2c6 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&i2c6m3_xfer>;
>> + status = "okay";
>> +
>> + hym8563: rtc at 51 {
>> + compatible = "haoyu,hym8563";
>> + reg = <0x51>;
>> + #clock-cells = <0>;
>> + clock-output-names = "hym8563";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&hym8563_int>;
>> + interrupt-parent = <&gpio0>;
>> + interrupts = <RK_PB0 IRQ_TYPE_LEVEL_LOW>;
>> + wakeup-source;
>> + };
>> +};
>> +
>> +&mdio1 {
>> + rgmii_phy1: ethernet-phy at 1 {
>> + compatible = "ethernet-phy-ieee802.3-c22";
>> + reg = <0x1>;
>> + };
>> +};
>> +
>> +&pcie2x1l2 {
>> + reset-gpios = <&gpio3 RK_PD1 GPIO_ACTIVE_HIGH>;
>> + vpcie3v3-supply = <&vcc3v3_pcie2x1l2>;
>> + rockchip,skip-scan-in-resume;
>
> There's no such property.
Will remove it.
>
>> + status = "okay";
>> +};
>> +
>> +&pinctrl {
>> + gpio-func {
>> + leds_gpio: leds-gpio {
>> + rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
>> + };
>> + };
>> +
>> + hym8563 {
>> + hym8563_int: hym8563-int {
>> + rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
>> + };
>> + };
>> +
>> + sata {
>> + sata_reset:sata-reset{
>> + rockchip,pins = <3 RK_PD1 RK_FUNC_GPIO &pcfg_pull_up>;
>
> Not what you think: https://megous.com/dl/tmp/f135580b68cb5dfe.png
>
>> + };
>> + };
>> +};
>> +
>> +&pwm2 {
>> + pinctrl-names = "active";
>> + pinctrl-0 = <&pwm2m0_pins>;
>> + status = "okay";
>> +};
>> +
>> +&pwm6 {
>> + pinctrl-names = "active";
>> + pinctrl-0 = <&pwm6m0_pins>;
>> + status = "okay";
>> +};
>> +
>> +&saradc {
>> + vref-supply = <&avcc_1v8_s0>;
>> + status = "okay";
>> +};
>> +
>> +&sata0 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&sata_reset>;
>> + status = "disabled";
>> +};
>
> Where do you see a SATA port? http://www.orangepi.org/html/hardWare/computerAndMicrocontrollers/details/Orange-Pi-5.html
>
> Or a reset signal in the schematic?
It's needed to use sata node once you want to use mSata SSD. I don't know if it works without sata_reset pinctrl. Don't have mSata SSD to try.
>
>> +&sdmmc {
>> + max-frequency = <150000000>;
>> + no-sdio;
>> + no-mmc;
>> + bus-width = <4>;
>> + cap-mmc-highspeed;
>> + cap-sd-highspeed;
>> + disable-wp;
>> + sd-uhs-sdr104;
>> + vmmc-supply = <&vcc_3v3_sd_s0>;
>> + vqmmc-supply = <&vccio_sd_s0>;
>> + status = "okay";
>> +};
>> +
>> +&sfc {
>> + pinctrl-0 = <&fspim0_pins>;
>> + pinctrl-names = "default";
>> + max-freq = <100000000>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "okay";
>> +
>> + spi_flash: spi-flash at 0 {
>> + compatible = "jedec,spi-nor";
>> + reg = <0x0>;
>> + spi-max-frequency = <100000000>;
>> + spi-tx-bus-width = <1>;
>> + spi-rx-bus-width = <4>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "okay";
>> +
>> + partitions {
>> + compatible = "fixed-partitions";
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> +
>> + loader at 0 {
>> + label = "loader";
>> + reg = <0x0 0x1000000>;
>> + };
>> + };
>
> Partitions are not really needed.
Will remove it.
>
>> + };
>> +};
>> +
>> +&spi2 {
>> + status = "okay";
>> + assigned-clocks = <&cru CLK_SPI2>;
>> + assigned-clock-rates = <200000000>;
>> + num-cs = <1>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&spi2m2_cs0 &spi2m2_pins>;
>> +
>> + pmic at 0 {
>> + compatible = "rockchip,rk806";
>> + reg = <0x0>;
>> + interrupt-parent = <&gpio0>;
>> + interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>,
>> + <&rk806_dvs2_null>, <&rk806_dvs3_null>;
>> + spi-max-frequency = <1000000>;
>> +
>> + vcc1-supply = <&vcc5v0_sys>;
>> + vcc2-supply = <&vcc5v0_sys>;
>> + vcc3-supply = <&vcc5v0_sys>;
>> + vcc4-supply = <&vcc5v0_sys>;
>> + vcc5-supply = <&vcc5v0_sys>;
>> + vcc6-supply = <&vcc5v0_sys>;
>> + vcc7-supply = <&vcc5v0_sys>;
>> + vcc8-supply = <&vcc5v0_sys>;
>> + vcc9-supply = <&vcc5v0_sys>;
>> + vcc10-supply = <&vcc5v0_sys>;
>> + vcc11-supply = <&vcc_2v0_pldo_s3>;
>> + vcc12-supply = <&vcc5v0_sys>;
>> + vcc13-supply = <&vcc_1v1_nldo_s3>;
>> + vcc14-supply = <&vcc_1v1_nldo_s3>;
>> + vcca-supply = <&vcc5v0_sys>;
>> +
>> + gpio-controller;
>> + #gpio-cells = <2>;
>> +
>> + rk806_dvs1_null: dvs1-null-pins {
>> + pins = "gpio_pwrctrl2";
>> + function = "pin_fun0";
>> + };
>> +
>> + rk806_dvs2_null: dvs2-null-pins {
>> + pins = "gpio_pwrctrl2";
>> + function = "pin_fun0";
>> + };
>> +
>> + rk806_dvs3_null: dvs3-null-pins {
>> + pins = "gpio_pwrctrl3";
>> + function = "pin_fun0";
>> + };
>> +
>> + regulators {
>> + vdd_gpu_s0: vdd_gpu_mem_s0: dcdc-reg1 {
>> + regulator-name = "vdd_gpu_s0";
>> + regulator-boot-on;
>> + regulator-min-microvolt = <550000>;
>> + regulator-max-microvolt = <950000>;
>> + regulator-ramp-delay = <12500>;
>> + regulator-enable-ramp-delay = <400>;
>> +
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + vdd_cpu_lit_s0: vdd_cpu_lit_mem_s0: dcdc-reg2 {
>> + regulator-name = "vdd_cpu_lit_s0";
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <550000>;
>> + regulator-max-microvolt = <950000>;
>> + regulator-ramp-delay = <12500>;
>> +
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + vdd_log_s0: dcdc-reg3 {
>> + regulator-name = "vdd_log_s0";
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <675000>;
>> + regulator-max-microvolt = <750000>;
>> + regulator-ramp-delay = <12500>;
>> +
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + regulator-suspend-microvolt = <750000>;
>> + };
>> + };
>> +
>> + vdd_vdenc_s0: vdd_vdenc_mem_s0: dcdc-reg4 {
>> + regulator-name = "vdd_vdenc_s0";
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <550000>;
>> + regulator-max-microvolt = <950000>;
>> + regulator-ramp-delay = <12500>;
>> +
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + vdd_ddr_s0: dcdc-reg5 {
>> + regulator-name = "vdd_ddr_s0";
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <675000>;
>> + regulator-max-microvolt = <900000>;
>> + regulator-ramp-delay = <12500>;
>> +
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + regulator-suspend-microvolt = <850000>;
>> + };
>> + };
>> +
>> + vdd2_ddr_s3: dcdc-reg6 {
>> + regulator-name = "vdd2_ddr_s3";
>> + regulator-always-on;
>> + regulator-boot-on;
>> +
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + };
>> + };
>> +
>> + vcc_2v0_pldo_s3: dcdc-reg7 {
>> + regulator-name = "vdd_2v0_pldo_s3";
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <2000000>;
>> + regulator-max-microvolt = <2000000>;
>> + regulator-ramp-delay = <12500>;
>> +
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + regulator-suspend-microvolt = <2000000>;
>> + };
>> + };
>> +
>> + vcc_3v3_s3: dcdc-reg8 {
>> + regulator-name = "vcc_3v3_s3";
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> +
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + regulator-suspend-microvolt = <3300000>;
>> + };
>> + };
>> +
>> + vddq_ddr_s0: dcdc-reg9 {
>> + regulator-name = "vddq_ddr_s0";
>> + regulator-always-on;
>> + regulator-boot-on;
>> +
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + vcc_1v8_s3: dcdc-reg10 {
>> + regulator-name = "vcc_1v8_s3";
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> +
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + regulator-suspend-microvolt = <1800000>;
>> + };
>> + };
>> +
>> + avcc_1v8_s0: pldo-reg1 {
>> + regulator-name = "avcc_1v8_s0";
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> +
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + vcc_1v8_s0: pldo-reg2 {
>> + regulator-name = "vcc_1v8_s0";
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> +
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + regulator-suspend-microvolt = <1800000>;
>> + };
>> + };
>> +
>> + avdd_1v2_s0: pldo-reg3 {
>> + regulator-name = "avdd_1v2_s0";
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <1200000>;
>> + regulator-max-microvolt = <1200000>;
>> +
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + vcc_3v3_s0: pldo-reg4 {
>> + regulator-name = "vcc_3v3_s0";
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-ramp-delay = <12500>;
>> +
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + vccio_sd_s0: pldo-reg5 {
>> + regulator-name = "vccio_sd_s0";
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-ramp-delay = <12500>;
>> +
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + pldo6_s3: pldo-reg6 {
>> + regulator-name = "pldo6_s3";
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> +
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + regulator-suspend-microvolt = <1800000>;
>> + };
>> + };
>> +
>> + vdd_0v75_s3: nldo-reg1 {
>> + regulator-name = "vdd_0v75_s3";
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <750000>;
>> + regulator-max-microvolt = <750000>;
>> +
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + regulator-suspend-microvolt = <750000>;
>> + };
>> + };
>> +
>> + vdd_ddr_pll_s0: nldo-reg2 {
>> + regulator-name = "vdd_ddr_pll_s0";
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <850000>;
>> + regulator-max-microvolt = <850000>;
>> +
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + regulator-suspend-microvolt = <850000>;
>> + };
>> + };
>> +
>> + avdd_0v75_s0: nldo-reg3 {
>> + regulator-name = "avdd_0v75_s0";
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <750000>;
>> + regulator-max-microvolt = <750000>;
>> +
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + vdd_0v85_s0: nldo-reg4 {
>> + regulator-name = "vdd_0v85_s0";
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <850000>;
>> + regulator-max-microvolt = <850000>;
>> +
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + vdd_0v75_s0: nldo-reg5 {
>> + regulator-name = "vdd_0v75_s0";
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <750000>;
>> + regulator-max-microvolt = <750000>;
>> +
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>
> Have you checked all of the above regulators against the schematic?
Just checked bucks roughly. I think they are OK.
>
>> + };
>> + };
>> +};
>> +
>> +&tsadc {
>> + status = "okay";
>> +};
>> +
>> +&uart2 {
>> + pinctrl-0 = <&uart2m0_xfer>;
>> + status = "okay";
>> +};
>> +
>> +&u2phy0 {
>> + status = "okay";
>> +};
>> +
>> +&u2phy0_otg {
>> + rockchip,typec-vbus-det;
>
> No such property.
Will remove it.
>
> That's all from me, but it's not an exhaustive list of issues. You should
> go through the schematic and verify that every single node in DT actually
> matches what's in there.
>
> kind regards,
> o.
>
>> + status = "okay";
>> +};
>> +
>> +&u2phy2 {
>> + status = "okay";
>> +};
>> +
>> +&u2phy2_host {
>> + status = "okay";
>> +};
>> +
>> +&u2phy3 {
>> + status = "okay";
>> +};
>> +
>> +&u2phy3_host {
>> + status = "okay";
>> +};
>> +
>> +&usb_host0_ehci {
>> + status = "okay";
>> +};
>> +
>> +&usb_host0_ohci {
>> + status = "okay";
>> +};
>> +
>> +&usb_host1_ehci {
>> + status = "okay";
>> +};
>> +
>> +&usb_host1_ohci {
>> + status = "okay";
>> +};
>>
>> +&wdt {
>> + status = "okay";
>> +};
>> --
>> 2.41.0
>>
Regards,
Efe
More information about the linux-arm-kernel
mailing list