[PATCH 2/3] arm64: dts: ti: k3-j7200: Add the supported frequencies for A72

[Kumar, Udit]

On 8/10/2023 12:39 AM, Nishanth Menon wrote:
> On 23:09-20230809, Apurva Nandan wrote:
>> From: Keerthy <j-keerthy at ti.com>
>>
>> Add 750M, 1G, 1.5G & 2G as the supported frequencies for A72.
>> This enables support for Dynamic Frequency Scaling(DFS)
>>
>> Signed-off-by: Keerthy <j-keerthy at ti.com>
>> Signed-off-by: Apurva Nandan <a-nandan at ti.com>
>> ---
>>   arch/arm64/boot/dts/ti/k3-j7200.dtsi | 28 ++++++++++++++++++++++++++++
>>   1 file changed, 28 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/ti/k3-j7200.dtsi b/arch/arm64/boot/dts/ti/k3-j7200.dtsi
>> index ef73e6d7e858..7222c453096f 100644
>> --- a/arch/arm64/boot/dts/ti/k3-j7200.dtsi
>> +++ b/arch/arm64/boot/dts/ti/k3-j7200.dtsi
>> @@ -48,6 +48,10 @@ cpu0: cpu at 0 {
>>   			d-cache-line-size = <64>;
>>   			d-cache-sets = <256>;
>>   			next-level-cache = <&L2_0>;
>> +			clocks = <&k3_clks 202 2>;
>> +			clock-names = "cpu";
>> +			operating-points-v2 = <&cpu0_opp_table>;
>> +			#cooling-cells = <2>; /* min followed by max */
>>   		};
>>   
>>   		cpu1: cpu at 1 {
>> @@ -62,6 +66,30 @@ cpu1: cpu at 1 {
>>   			d-cache-line-size = <64>;
>>   			d-cache-sets = <256>;
>>   			next-level-cache = <&L2_0>;
>> +			clocks = <&k3_clks 203 0>;
>> +			clock-names = "cpu";
>> +			operating-points-v2 = <&cpu0_opp_table>;
>> +			#cooling-cells = <2>; /* min followed by max */
>> +		};
>> +	};
>> +
>> +	cpu0_opp_table: opp-table {
>> +		compatible = "operating-points-v2";
>> +
>> +		opp4-2000000000 {
>> +			opp-hz = /bits/ 64 <2000000000>;
>> +		};
>> +
>> +		opp3-1500000000 {
>> +			opp-hz = /bits/ 64 <1500000000>;
>> +		};
>> +
>> +		opp2-1000000000 {
>> +			opp-hz = /bits/ 64 <1000000000>;
>> +		};
>> +
>> +		opp1-750000000 {
>> +			opp-hz = /bits/ 64 <750000000>;
>>   		};
>>   	};
>>   
>> -- 
>> 2.34.1
>>
> Are you sure this is correct to enable all OPPs without efuse bit checks?
>
> https://www.ti.com/lit/ds/symlink/dra821u-q1.pdf
> 7.5 Operating Performance Points
> DRA821xC operates only upto 750MHz
> DRA821xE at 1GHz
> DRA821xL upto 1.5GHz and
> DRA821xT upto 2GHz

Looks, top SKUs is considered here .

After detecting which SKU we are running (I hope TRM should have this 
information- through efuse or some other register)

I think, we can follow two approaches.

1) have OPP table for each SKU and select based SKUs type or

2) Do run time fixup by u-boot based upon SKU type