[PATCH 0/1] Re: [PATCH-next v1] arm64: dts: rockchip: Enable NVM Express PCIe controller on rock3a

[Chukun Pan]

Hi Anand,

> No, It's not working on my board.
> If you check the driver code it requires *data-line* and *num-lanes
> from the dts.

I have successfully tested NVME hard drives on my board. See
below for the patch, looking forward to your testing.

root at rock3a:~# lspci
0000:00:00.0 PCI bridge: Rockchip Electronics Co., Ltd \
             RK3568 Remote Signal Processor (rev 01)
0000:01:00.0 Network controller: MEDIATEK Corp. MT7921 \
             802.11ax PCI Express Wireless Network Adapter
0002:00:00.0 PCI bridge: Rockchip Electronics Co., Ltd \
             RK3568 Remote Signal Processor (rev 01)
0002:01:00.0 Non-Volatile memory controller: Sandisk Corp \
             PC SN520 NVMe SSD (rev 01)

Patch:

--- a/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
@@ -67,6 +67,37 @@ vcc12v_dcin: vcc12v-dcin-regulator {
 		regulator-boot-on;
 	};
 
+	pcie30_avdd0v9: pcie30-avdd0v9-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "pcie30_avdd0v9";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <900000>;
+		regulator-max-microvolt = <900000>;
+		vin-supply = <&vcc3v3_sys>;
+	};
+
+	pcie30_avdd1v8: pcie30-avdd1v8-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "pcie30_avdd1v8";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc3v3_sys>;
+	};
+
+	/* pi6c pcie clock generator */
+	vcc3v3_pi6c_03: vcc3v3-pi6c-03-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_pi6c_03";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
 	vcc3v3_pcie: vcc3v3-pcie-regulator {
 		compatible = "regulator-fixed";
 		enable-active-high;
@@ -546,6 +577,19 @@ &pcie2x1 {
 	status = "okay";
 };
 
+&pcie30phy {
+	phy-supply = <&vcc3v3_pi6c_03>;
+	status = "okay";
+};
+
+&pcie3x2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie30x2m1_pins>;
+	reset-gpios = <&gpio2 RK_PD6 GPIO_ACTIVE_HIGH>;
+	vpcie3v3-supply = <&vcc3v3_pcie>;
+	status = "okay";
+};
+
 &pinctrl {
 	cam {
 		vcc_cam_en: vcc_cam_en {
-- 
2.25.1

Thanks,
Chukun