[PATCH v2 2/5] pwm: Add support for the MSTAR MSC313 PWM
Uwe Kleine-König
u.kleine-koenig at pengutronix.de
Tue Sep 27 09:33:14 PDT 2022
Hello Romain, hello Daniel,
adding Mark Brown to Cc: for the regmap stuff.
On Wed, Sep 07, 2022 at 03:12:38PM +0200, Romain Perier wrote:
> From: Daniel Palmer <daniel at 0x0f.com>
>
> This adds support for the PWM block on the Mstar MSC313e SoCs and newer.
>
> Signed-off-by: Daniel Palmer <daniel at 0x0f.com>
> Co-developed-by: Romain Perier <romain.perier at gmail.com>
> Signed-off-by: Romain Perier <romain.perier at gmail.com>
> ---
> MAINTAINERS | 1 +
> drivers/pwm/Kconfig | 9 ++
> drivers/pwm/Makefile | 1 +
> drivers/pwm/pwm-msc313e.c | 269 ++++++++++++++++++++++++++++++++++++++
> 4 files changed, 280 insertions(+)
> create mode 100644 drivers/pwm/pwm-msc313e.c
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 9d7f64dc0efe..c3b39b09097c 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -2439,6 +2439,7 @@ F: arch/arm/mach-mstar/
> F: drivers/clk/mstar/
> F: drivers/clocksource/timer-msc313e.c
> F: drivers/gpio/gpio-msc313.c
> +F: drivers/pwm/pwm-msc313e.c
> F: drivers/rtc/rtc-msc313.c
> F: drivers/watchdog/msc313e_wdt.c
> F: include/dt-bindings/clock/mstar-*
> diff --git a/drivers/pwm/Kconfig b/drivers/pwm/Kconfig
> index 60d13a949bc5..8049fd03a821 100644
> --- a/drivers/pwm/Kconfig
> +++ b/drivers/pwm/Kconfig
> @@ -372,6 +372,15 @@ config PWM_MESON
> To compile this driver as a module, choose M here: the module
> will be called pwm-meson.
>
> +config PWM_MSC313E
> + tristate "MStar MSC313e PWM support"
> + depends on ARCH_MSTARV7 || COMPILE_TEST
> + help
> + Generic PWM framework driver for MSTAR MSC313e.
> +
> + To compile this driver as a module, choose M here: the module
> + will be called pwm-msc313e.
> +
> config PWM_MTK_DISP
> tristate "MediaTek display PWM driver"
> depends on ARCH_MEDIATEK || COMPILE_TEST
> diff --git a/drivers/pwm/Makefile b/drivers/pwm/Makefile
> index 7bf1a29f02b8..bc285c054f2a 100644
> --- a/drivers/pwm/Makefile
> +++ b/drivers/pwm/Makefile
> @@ -62,4 +62,5 @@ obj-$(CONFIG_PWM_TWL) += pwm-twl.o
> obj-$(CONFIG_PWM_TWL_LED) += pwm-twl-led.o
> obj-$(CONFIG_PWM_VISCONTI) += pwm-visconti.o
> obj-$(CONFIG_PWM_VT8500) += pwm-vt8500.o
> +obj-$(CONFIG_PWM_MSC313E) += pwm-msc313e.o
> obj-$(CONFIG_PWM_XILINX) += pwm-xilinx.o
> diff --git a/drivers/pwm/pwm-msc313e.c b/drivers/pwm/pwm-msc313e.c
> new file mode 100644
> index 000000000000..a71f39ba66c3
> --- /dev/null
> +++ b/drivers/pwm/pwm-msc313e.c
> @@ -0,0 +1,269 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2021 Daniel Palmer <daniel at thingy.jp>
> + * Copyright (C) 2022 Romain Perier <romain.perier at gmail.com>
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/of_device.h>
> +#include <linux/pwm.h>
> +#include <linux/regmap.h>
> +
> +#define DRIVER_NAME "msc313e-pwm"
> +
> +#define CHANNEL_OFFSET 0x80
> +#define REG_DUTY 0x8
> +#define REG_PERIOD 0x10
> +#define REG_DIV 0x18
> +#define REG_CTRL 0x1c
> +#define REG_SWRST 0x1fc
> +
> +struct msc313e_pwm_channel {
> + struct regmap_field *clkdiv;
> + struct regmap_field *polarity;
> + struct regmap_field *dutyl;
> + struct regmap_field *dutyh;
> + struct regmap_field *periodl;
> + struct regmap_field *periodh;
> + struct regmap_field *swrst;
> +};
> +
> +struct msc313e_pwm {
> + struct regmap *regmap;
> + struct pwm_chip pwmchip;
> + struct clk *clk;
> + struct msc313e_pwm_channel channels[];
> +};
> +
> +struct msc313e_pwm_info {
> + unsigned int channels;
> +};
> +
> +#define to_msc313e_pwm(ptr) container_of(ptr, struct msc313e_pwm, pwmchip)
> +
> +static const struct regmap_config msc313e_pwm_regmap_config = {
> + .reg_bits = 16,
> + .val_bits = 16,
> + .reg_stride = 4,
> +};
> +
> +static const struct msc313e_pwm_info msc313e_data = {
> + .channels = 8,
> +};
> +
> +static const struct msc313e_pwm_info ssd20xd_data = {
> + .channels = 4,
> +};
> +
> +static void msc313e_pwm_writecounter(struct regmap_field *low, struct regmap_field *high, u32 value)
> +{
> + /* The bus that connects the CPU to the peripheral registers splits 32 bit registers into
Please fix the comment style to use /* on a line for itself. Also for
comments staying below 80 chars per line is appreciated.
> + * two 16bit registers placed 4 bytes apart. It's the hardware design they used. The counter
> + * we are about to write has this contrainst.
s/contrainst/contraint/
I wonder if that could be abstracted by regmap?!
> + */
> + regmap_field_write(low, value & 0xffff);
> + regmap_field_write(high, value >> 16);
> +}
> +
> +static void msc313e_pwm_readcounter(struct regmap_field *low, struct regmap_field *high, u32 *value)
> +{
> + unsigned int val = 0;
> +
> + regmap_field_read(low, &val);
> + *value = val;
> + regmap_field_read(high, &val);
> + *value = (val << 16) | *value;
> +}
> +
> +static int msc313e_pwm_config(struct pwm_chip *chip, struct pwm_device *device,
> + int duty_ns, int period_ns)
> +{
> + struct msc313e_pwm *pwm = to_msc313e_pwm(chip);
> + unsigned long long nspertick = DIV_ROUND_DOWN_ULL(NSEC_PER_SEC, clk_get_rate(pwm->clk));
> + struct msc313e_pwm_channel *channel = &pwm->channels[device->hwpwm];
> + unsigned long long div = 1;
> +
> + /* Fit the period into the period register by prescaling the clk */
> + while (DIV_ROUND_DOWN_ULL(period_ns, nspertick) > 0x3ffff) {
dividing by the result of a division looses precision. Also rounding
down both divisions looks wrong.
> + div++;
> + if (div > (0xffff + 1)) {
> + /* Force clk div to the maximum allowed value */
> + div = 0xffff;
> + break;
> + }
> + nspertick = DIV_ROUND_DOWN_ULL(nspertick, div);
> + }
> +
> + regmap_field_write(channel->clkdiv, div - 1);
> + msc313e_pwm_writecounter(channel->dutyl, channel->dutyh,
> + DIV_ROUND_DOWN_ULL(duty_ns, nspertick));
> + msc313e_pwm_writecounter(channel->periodl, channel->periodh,
> + DIV_ROUND_DOWN_ULL(period_ns, nspertick));
> + return 0;
> +};
> +
> +static int msc313e_pwm_set_polarity(struct pwm_chip *chip, struct pwm_device *device,
> + enum pwm_polarity polarity)
> +{
> + struct msc313e_pwm *pwm = to_msc313e_pwm(chip);
> + struct msc313e_pwm_channel *channel = &pwm->channels[device->hwpwm];
> + unsigned int pol = 0;
> +
> + if (polarity == PWM_POLARITY_INVERSED)
> + pol = 1;
> + regmap_field_update_bits(channel->polarity, 1, pol);
> +
> + return 0;
> +}
> +
> +static int msc313e_pwm_enable(struct pwm_chip *chip, struct pwm_device *device)
> +{
> + struct msc313e_pwm *pwm = to_msc313e_pwm(chip);
> + struct msc313e_pwm_channel *channel = &pwm->channels[device->hwpwm];
> + int ret;
> +
> + ret = clk_prepare_enable(pwm->clk);
> + if (ret)
> + return ret;
> + return regmap_field_write(channel->swrst, 0);
> +}
> +
> +static int msc313e_pwm_disable(struct pwm_chip *chip, struct pwm_device *device)
> +{
> + struct msc313e_pwm *pwm = to_msc313e_pwm(chip);
> + struct msc313e_pwm_channel *channel = &pwm->channels[device->hwpwm];
> + int ret;
> +
> + ret = regmap_field_write(channel->swrst, 1);
> + clk_disable_unprepare(pwm->clk);
> + return ret;
> +}
> +
> +static int msc313e_apply(struct pwm_chip *chip, struct pwm_device *pwm,
> + const struct pwm_state *state)
> +{
> + int ret;
> +
> + if (state->enabled) {
> + if (!pwm->state.enabled) {
> + ret = msc313e_pwm_enable(chip, pwm);
> + if (ret)
> + return ret;
> + }
> + msc313e_pwm_set_polarity(chip, pwm, state->polarity);
> + msc313e_pwm_config(chip, pwm, state->duty_cycle, state->period);
Does the output emit a previous setting after msc313e_pwm_enable()? If
so, please do the enable at the end.
Does calling msc313e_pwm_set_polarity() and msc313e_pwm_config() have an
immediate effect? Or is the currently running period completed?
> + } else if (pwm->state.enabled) {
> + ret = msc313e_pwm_disable(chip, pwm);
How does the output behave on disable? Typical options are:
- freezes where ever it currently is
- goes to the inactive level
Does it complete the currently running period? Please answer these in a
"Limitations:" section similar to e.g. pwm-sl28cpld.c and pwm-iqs620a.
> + }
> + return 0;
> +}
> +
> +static void msc313e_get_state(struct pwm_chip *chip, struct pwm_device *device,
Please s/device/pwm/ to match the naming used in other drivers.
> + struct pwm_state *state)
> +{
> + struct msc313e_pwm *pwm = to_msc313e_pwm(chip);
> + struct msc313e_pwm_channel *channel = &pwm->channels[device->hwpwm];
> + unsigned long long nspertick = DIV_ROUND_DOWN_ULL(NSEC_PER_SEC, clk_get_rate(pwm->clk));
> + unsigned int val = 0;
> +
> + regmap_field_read(channel->polarity, &val);
> + state->polarity = val ? PWM_POLARITY_INVERSED : PWM_POLARITY_NORMAL;
> +
> + regmap_field_read(channel->swrst, &val);
> + state->enabled = val == 0 ? true : false;
> +
> + msc313e_pwm_readcounter(channel->dutyl, channel->dutyh, &val);
> + state->duty_cycle = val * nspertick;
Please do the division at the end. Consider val = 333335 and
clk_get_rate() returning 666666667.
Then the exact duty cycle would be 500002.49974999874 but you would
calculate nspertick = 1 and so duty_cycle = 333335.
Also you need to round up. Did you test your driver with PWM_DEBUG
enabled? The idea is that .get_state should return 500003 here to have
apply ∘ get_state idempotent. As apply is supposed to round down to the
next available setting, get_state has to round up.
> + msc313e_pwm_readcounter(channel->periodl, channel->periodh, &val);
> + state->period = val * nspertick;
> +}
> +
> +static const struct pwm_ops msc313e_pwm_ops = {
> + .apply = msc313e_apply,
> + .get_state = msc313e_get_state,
> + .owner = THIS_MODULE
> +};
> +
> +static int msc313e_pwm_probe(struct platform_device *pdev)
> +{
> + const struct msc313e_pwm_info *match_data;
> + struct device *dev = &pdev->dev;
> + struct msc313e_pwm *pwm;
> + __iomem void *base;
> + int i;
> +
> + match_data = of_device_get_match_data(dev);
> + if (!match_data)
> + return -EINVAL;
> +
> + base = devm_platform_ioremap_resource(pdev, 0);
> + if (IS_ERR(base))
> + return PTR_ERR(base);
> +
> + pwm = devm_kzalloc(dev, struct_size(pwm, channels, match_data->channels), GFP_KERNEL);
Please don't use "pwm" as a name for your driver data variable. That
name is reserved for struct pwm_device pointers. Something like "ddata"
would be fine, but there is a wide variety in pwm driver land to choose
from.
> + if (!pwm)
> + return -ENOMEM;
> +
> + pwm->clk = devm_clk_get(dev, NULL);
> + if (IS_ERR(pwm->clk))
> + return dev_err_probe(dev, PTR_ERR(pwm->clk), "Cannot get clk\n");
> +
> + pwm->regmap = devm_regmap_init_mmio(dev, base, &msc313e_pwm_regmap_config);
> + if (IS_ERR(pwm->regmap))
> + return dev_err_probe(dev, PTR_ERR(pwm->regmap), "Cannot get regmap\n");
> +
> + for (i = 0; i < match_data->channels; i++) {
> + unsigned int offset = CHANNEL_OFFSET * i;
> + struct reg_field div_clkdiv_field = REG_FIELD(offset + REG_DIV, 0, 7);
> + struct reg_field ctrl_polarity_field = REG_FIELD(offset + REG_CTRL, 4, 4);
> + struct reg_field dutyl_field = REG_FIELD(offset + REG_DUTY, 0, 15);
> + struct reg_field dutyh_field = REG_FIELD(offset + REG_DUTY + 4, 0, 2);
> + struct reg_field periodl_field = REG_FIELD(offset + REG_PERIOD, 0, 15);
> + struct reg_field periodh_field = REG_FIELD(offset + REG_PERIOD + 4, 0, 2);
> + struct reg_field swrst_field = REG_FIELD(REG_SWRST, i, i);
> +
> + pwm->channels[i].clkdiv = devm_regmap_field_alloc(dev, pwm->regmap,
> + div_clkdiv_field);
> + pwm->channels[i].polarity = devm_regmap_field_alloc(dev, pwm->regmap,
> + ctrl_polarity_field);
> + pwm->channels[i].dutyl = devm_regmap_field_alloc(dev, pwm->regmap, dutyl_field);
> + pwm->channels[i].dutyh = devm_regmap_field_alloc(dev, pwm->regmap, dutyh_field);
> + pwm->channels[i].periodl = devm_regmap_field_alloc(dev, pwm->regmap, periodl_field);
> + pwm->channels[i].periodh = devm_regmap_field_alloc(dev, pwm->regmap, periodh_field);
> + pwm->channels[i].swrst = devm_regmap_field_alloc(dev, pwm->regmap, swrst_field);
> +
> + /* Channels are enabled on boot, disable it until the pwm subsystem re-enable it
> + * explicitly
You're supposed to keep the PWM running. (Consider a bootloader setting
up a splash screen. You're probably killing the backlight here.) Note
you need improved clk handling to do that right.
> + */
> + regmap_field_write(pwm->channels[i].swrst, 1);
> + }
> +
> + pwm->pwmchip.dev = dev;
> + pwm->pwmchip.ops = &msc313e_pwm_ops;
> + pwm->pwmchip.npwm = match_data->channels;
> +
> + platform_set_drvdata(pdev, pwm);
This is unused, please drop.
> + return devm_pwmchip_add(dev, &pwm->pwmchip);
> +}
> +
> +static const struct of_device_id msc313e_pwm_dt_ids[] = {
> + { .compatible = "mstar,msc313e-pwm", .data = &msc313e_data },
> + { .compatible = "mstar,ssd20xd-pwm", .data = &ssd20xd_data },
> + {},
> +};
> +MODULE_DEVICE_TABLE(of, msc313e_pwm_dt_ids);
> +
> +static struct platform_driver msc313e_pwm_driver = {
> + .probe = msc313e_pwm_probe,
> + .driver = {
> + .name = DRIVER_NAME,
> + .of_match_table = msc313e_pwm_dt_ids,
> + },
> +};
> +module_platform_driver(msc313e_pwm_driver);
> +
> +MODULE_LICENSE("GPL v2");
> +MODULE_DESCRIPTION("Mstar MSC313e PWM driver");
> +MODULE_AUTHOR("Daniel Palmer <daniel at thingy.jp>");
That address doesn't match the author of this patch. Is this on purpose?
Best regards
Uwe
--
Pengutronix e.K. | Uwe Kleine-König |
Industrial Linux Solutions | https://www.pengutronix.de/ |
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 488 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20220927/609fe7b1/attachment.sig>
More information about the linux-arm-kernel
mailing list