[PATCH v2 03/10] PCI: aardvark: Send Set_Slot_Power_Limit message
Marek Behún
kabel at kernel.org
Tue Sep 27 07:19:19 PDT 2022
From: Pali Rohár <pali at kernel.org>
Emulate Slot PowerLimit Scale and Value bits in the Slot Capabilities
register of the emulated bridge and if slot power limit value is
defined, send that Set_Slot_Power_Limit message via Message Generation
Control Register in Link Up handler on link up event.
Slot power limit value is read from device-tree property
'slot-power-limit-milliwatt'. If this property is not specified, we
treat it as "Slot Capabilities register has not yet been initialized".
According to PCIe Base specification 3.0, when transitioning from a
non-DL_Up Status to a DL_Up Status, the Port must initiate the
transmission of a Set_Slot_Power_Limit Message to the other component
on the Link to convey the value programmed in the Slot Power Limit
Scale and Value fields of the Slot Capabilities register. This
transmission is optional if the Slot Capabilities register has not
yet been initialized.
Signed-off-by: Pali Rohár <pali at kernel.org>
Signed-off-by: Marek Behún <kabel at kernel.org>
---
drivers/pci/controller/pci-aardvark.c | 51 ++++++++++++++++++++++++---
1 file changed, 47 insertions(+), 4 deletions(-)
diff --git a/drivers/pci/controller/pci-aardvark.c b/drivers/pci/controller/pci-aardvark.c
index 31da28ebc5d1..03e318bc171f 100644
--- a/drivers/pci/controller/pci-aardvark.c
+++ b/drivers/pci/controller/pci-aardvark.c
@@ -213,6 +213,11 @@ enum {
};
#define VENDOR_ID_REG (LMI_BASE_ADDR + 0x44)
+#define PME_MSG_GEN_CTRL (LMI_BASE_ADDR + 0x220)
+#define SEND_SET_SLOT_POWER_LIMIT BIT(13)
+#define SEND_PME_TURN_OFF BIT(14)
+#define SLOT_POWER_LIMIT_DATA_SHIFT 16
+#define SLOT_POWER_LIMIT_DATA_MASK GENMASK(25, 16)
/* PCIe core controller registers */
#define CTRL_CORE_BASE_ADDR 0x18000
@@ -285,6 +290,8 @@ struct advk_pcie {
raw_spinlock_t msi_irq_lock;
DECLARE_BITMAP(msi_used, MSI_IRQ_NUM);
struct mutex msi_used_lock;
+ u8 slot_power_limit_value;
+ u8 slot_power_limit_scale;
int link_gen;
bool link_was_up;
struct timer_list link_irq_timer;
@@ -317,8 +324,9 @@ static inline bool advk_pcie_link_up(struct advk_pcie *pcie)
{
/* check if LTSSM is in normal operation - some L* state */
u8 ltssm_state = advk_pcie_ltssm_state(pcie);
+ u16 slotsta, slotctl;
+ u32 slotpwr, val;
bool link_is_up;
- u16 slotsta;
link_is_up = ltssm_state >= LTSSM_L0 && ltssm_state < LTSSM_DISABLED;
@@ -332,6 +340,27 @@ static inline bool advk_pcie_link_up(struct advk_pcie *pcie)
pcie->bridge.pcie_conf.slotsta = cpu_to_le16(slotsta);
mod_timer(&pcie->link_irq_timer, jiffies + 1);
+
+ /*
+ * According to PCIe Base specification 3.0, when transitioning
+ * from a non-DL_Up Status to a DL_Up Status, the Port must
+ * initiate the transmission of a Set_Slot_Power_Limit Message
+ * to the other component on the Link to convey the value
+ * programmed in the Slot Power Limit Scale and Value fields of
+ * the Slot Capabilities register. This transmission is optional
+ * if the Slot Capabilities register has not yet been
+ * initialized.
+ */
+ slotctl = le16_to_cpu(pcie->bridge.pcie_conf.slotctl);
+ slotpwr = FIELD_GET(PCI_EXP_SLTCAP_SPLV | PCI_EXP_SLTCAP_SPLS,
+ le32_to_cpu(pcie->bridge.pcie_conf.slotcap));
+ if (!(slotctl & PCI_EXP_SLTCTL_ASPL_DISABLE) && slotpwr) {
+ val = advk_readl(pcie, PME_MSG_GEN_CTRL);
+ val &= ~SLOT_POWER_LIMIT_DATA_MASK;
+ val |= slotpwr << SLOT_POWER_LIMIT_DATA_SHIFT;
+ val |= SEND_SET_SLOT_POWER_LIMIT;
+ advk_writel(pcie, val, PME_MSG_GEN_CTRL);
+ }
}
return link_is_up;
@@ -944,8 +973,9 @@ advk_pci_bridge_emul_pcie_conf_write(struct pci_bridge_emul *bridge,
case PCI_EXP_SLTCTL: {
u16 slotctl = le16_to_cpu(bridge->pcie_conf.slotctl);
- /* Only emulation of HPIE and DLLSCE bits is provided */
- slotctl &= PCI_EXP_SLTCTL_HPIE | PCI_EXP_SLTCTL_DLLSCE;
+ /* Only emulation of HPIE, DLLSCE and ASPLD bits is provided */
+ slotctl &= PCI_EXP_SLTCTL_HPIE | PCI_EXP_SLTCTL_DLLSCE |
+ PCI_EXP_SLTCTL_ASPL_DISABLE;
bridge->pcie_conf.slotctl = cpu_to_le16(slotctl);
break;
}
@@ -1109,9 +1139,13 @@ static int advk_sw_pci_bridge_init(struct advk_pcie *pcie)
* Set physical slot number to 1 since there is only one port and zero
* value is reserved for ports within the same silicon as Root Port
* which is not our case.
+ *
+ * Set slot power limit.
*/
slotcap = PCI_EXP_SLTCAP_NCCS | PCI_EXP_SLTCAP_HPC |
- FIELD_PREP(PCI_EXP_SLTCAP_PSN, 1);
+ FIELD_PREP(PCI_EXP_SLTCAP_PSN, 1) |
+ FIELD_PREP(PCI_EXP_SLTCAP_SPLV, pcie->slot_power_limit_value) |
+ FIELD_PREP(PCI_EXP_SLTCAP_SPLS, pcie->slot_power_limit_scale);
bridge->pcie_conf.slotcap = cpu_to_le32(slotcap);
bridge->pcie_conf.slotsta = cpu_to_le16(PCI_EXP_SLTSTA_PDS);
@@ -1837,6 +1871,7 @@ static int advk_pcie_probe(struct platform_device *pdev)
struct advk_pcie *pcie;
struct pci_host_bridge *bridge;
struct resource_entry *entry;
+ u32 slot_power_limit;
int ret, irq;
bridge = devm_pci_alloc_host_bridge(dev, sizeof(struct advk_pcie));
@@ -1957,6 +1992,14 @@ static int advk_pcie_probe(struct platform_device *pdev)
else
pcie->link_gen = ret;
+ slot_power_limit = of_pci_get_slot_power_limit(dev->of_node,
+ &pcie->slot_power_limit_value,
+ &pcie->slot_power_limit_scale);
+ if (slot_power_limit)
+ dev_info(dev, "Slot Power Limit: %u.%uW\n",
+ slot_power_limit / 1000,
+ (slot_power_limit / 100) % 10);
+
ret = advk_pcie_setup_phy(pcie);
if (ret)
return ret;
--
2.35.1
More information about the linux-arm-kernel
mailing list