[PATCH] dt-bindings: media: st,stmipid02: Convert the text bindings to YAML
Marek Vasut
marex at denx.de
Mon Sep 26 17:55:38 PDT 2022
Convert the text STMIPID02 DT bindings to YAML DT format to permit
validation of DTs using this I2C CSI-2 to CPI bridge.
Signed-off-by: Marek Vasut <marex at denx.de>
---
Cc: Alexandre Torgue <alexandre.torgue at foss.st.com>
Cc: Benjamin Mugnier <benjamin.mugnier at foss.st.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski at linaro.org>
Cc: Mauro Carvalho Chehab <mchehab at kernel.org>
Cc: Maxime Coquelin <mcoquelin.stm32 at gmail.com>
Cc: Rob Herring <robh+dt at kernel.org>
Cc: Sylvain Petinot <sylvain.petinot at foss.st.com>
Cc: devicetree at vger.kernel.org
Cc: linux-media at vger.kernel.org
Cc: linux-stm32 at st-md-mailman.stormreply.com
To: linux-arm-kernel at lists.infradead.org
---
.../bindings/media/i2c/st,st-mipid02.txt | 82 --------
.../bindings/media/i2c/st,st-mipid02.yaml | 175 ++++++++++++++++++
2 files changed, 175 insertions(+), 82 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt
create mode 100644 Documentation/devicetree/bindings/media/i2c/st,st-mipid02.yaml
diff --git a/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt b/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt
deleted file mode 100644
index 7976e6c40a80a..0000000000000
--- a/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt
+++ /dev/null
@@ -1,82 +0,0 @@
-STMicroelectronics MIPID02 CSI-2 to PARALLEL bridge
-
-MIPID02 has two CSI-2 input ports, only one of those ports can be active at a
-time. Active port input stream will be de-serialized and its content outputted
-through PARALLEL output port.
-CSI-2 first input port is a dual lane 800Mbps per lane whereas CSI-2 second
-input port is a single lane 800Mbps. Both ports support clock and data lane
-polarity swap. First port also supports data lane swap.
-PARALLEL output port has a maximum width of 12 bits.
-Supported formats are RAW6, RAW7, RAW8, RAW10, RAW12, RGB565, RGB888, RGB444,
-YUV420 8-bit, YUV422 8-bit and YUV420 10-bit.
-
-Required Properties:
-- compatible: shall be "st,st-mipid02"
-- clocks: reference to the xclk input clock.
-- clock-names: shall be "xclk".
-- VDDE-supply: sensor digital IO supply. Must be 1.8 volts.
-- VDDIN-supply: sensor internal regulator supply. Must be 1.8 volts.
-
-Optional Properties:
-- reset-gpios: reference to the GPIO connected to the xsdn pin, if any.
- This is an active low signal to the mipid02.
-
-Required subnodes:
- - ports: A ports node with one port child node per device input and output
- port, in accordance with the video interface bindings defined in
- Documentation/devicetree/bindings/media/video-interfaces.txt. The
- port nodes are numbered as follows:
-
- Port Description
- -----------------------------
- 0 CSI-2 first input port
- 1 CSI-2 second input port
- 2 PARALLEL output
-
-Endpoint node required property for CSI-2 connection is:
-- data-lanes: shall be <1> for Port 1. for Port 0 dual-lane operation shall be
-<1 2> or <2 1>. For Port 0 single-lane operation shall be <1> or <2>.
-Endpoint node optional property for CSI-2 connection is:
-- lane-polarities: any lane can be inverted or not.
-
-Endpoint node required property for PARALLEL connection is:
-- bus-width: shall be set to <6>, <7>, <8>, <10> or <12>.
-Endpoint node optional properties for PARALLEL connection are:
-- hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
-LOW being the default.
-- vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
-LOW being the default.
-
-Example:
-
-mipid02: csi2rx at 14 {
- compatible = "st,st-mipid02";
- reg = <0x14>;
- status = "okay";
- clocks = <&clk_ext_camera_12>;
- clock-names = "xclk";
- VDDE-supply = <&vdd>;
- VDDIN-supply = <&vdd>;
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
- port at 0 {
- reg = <0>;
-
- ep0: endpoint {
- data-lanes = <1 2>;
- remote-endpoint = <&mipi_csi2_in>;
- };
- };
- port at 2 {
- reg = <2>;
-
- ep2: endpoint {
- bus-width = <8>;
- hsync-active = <0>;
- vsync-active = <0>;
- remote-endpoint = <¶llel_out>;
- };
- };
- };
-};
diff --git a/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.yaml b/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.yaml
new file mode 100644
index 0000000000000..2cb117d883368
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.yaml
@@ -0,0 +1,175 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/st,st-mipid02.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: STMicroelectronics MIPID02 CSI-2 to PARALLEL bridge
+
+maintainers:
+ - Mickael Guene <mickael.guene at foss.st.com>
+ - Marek Vasut <marex at denx.de>
+
+description:
+ MIPID02 has two CSI-2 input ports, only one of those ports can be
+ active at a time. Active port input stream will be de-serialized
+ and its content outputted through PARALLEL output port.
+ CSI-2 first input port is a dual lane 800Mbps per lane whereas CSI-2
+ second input port is a single lane 800Mbps. Both ports support clock
+ and data lane polarity swap. First port also supports data lane swap.
+ PARALLEL output port has a maximum width of 12 bits.
+ Supported formats are RAW6, RAW7, RAW8, RAW10, RAW12, RGB565, RGB888,
+ RGB444, YUV420 8-bit, YUV422 8-bit and YUV420 10-bit.
+
+properties:
+ compatible:
+ const: st,st-mipid02
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ clock-names:
+ description:
+ Reference to the xclk input clock.
+ items:
+ - const: xclk
+
+ VDDE-supply:
+ description:
+ Sensor digital IO supply. Must be 1.8 volts.
+
+ VDDIN-supply:
+ description:
+ Sensor internal regulator supply. Must be 1.8 volts.
+
+ reset-gpios:
+ description:
+ Reference to the GPIO connected to the xsdn pin, if any.
+ This is an active low signal to the mipid02.
+
+ ports:
+ $ref: /schemas/graph.yaml#/properties/ports
+ properties:
+ port at 0:
+ $ref: /schemas/graph.yaml#/$defs/port-base
+ unevaluatedProperties: false
+ description: CSI-2 first input port
+ properties:
+ endpoint:
+ $ref: /schemas/media/video-interfaces.yaml#
+ unevaluatedProperties: false
+
+ properties:
+ data-lanes:
+ description:
+ Single-lane operation shall be <1> or <2> .
+ Dual-lane operation shall be <1 2> or <2 1> .
+ minItems: 1
+ maxItems: 2
+ lane-polarity:
+ description:
+ Any lane can be inverted or not.
+ minItems: 1
+ maxItems: 2
+
+ required:
+ - data-lanes
+
+ port at 1:
+ $ref: /schemas/graph.yaml#/$defs/port-base
+ unevaluatedProperties: false
+ description: CSI-2 second input port
+ properties:
+ endpoint:
+ $ref: /schemas/media/video-interfaces.yaml#
+ unevaluatedProperties: false
+
+ properties:
+ data-lanes:
+ description:
+ Single-lane operation shall be <1> or <2> .
+ maxItems: 1
+ lane-polarity:
+ description:
+ Any lane can be inverted or not.
+ maxItems: 1
+
+ required:
+ - data-lanes
+
+ port at 2:
+ $ref: /schemas/graph.yaml#/$defs/port-base
+ unevaluatedProperties: false
+ description: Output port
+ properties:
+ endpoint:
+ $ref: /schemas/media/video-interfaces.yaml#
+ unevaluatedProperties: false
+
+ properties:
+ bus-width:
+ enum: [8, 10, 12, 14]
+ default: 8
+ hsync-active: true
+ vsync-active: true
+
+ required:
+ - bus-width
+
+ required:
+ - port at 0
+ - port at 2
+
+additionalProperties: false
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - clock-names
+ - VDDE-supply
+ - VDDIN-supply
+ - ports
+
+examples:
+ - |
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ mipid02: csi2rx at 14 {
+ compatible = "st,st-mipid02";
+ reg = <0x14>;
+ status = "okay";
+ clocks = <&clk_ext_camera_12>;
+ clock-names = "xclk";
+ VDDE-supply = <&vdd>;
+ VDDIN-supply = <&vdd>;
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port at 0 {
+ reg = <0>;
+
+ ep0: endpoint {
+ data-lanes = <1 2>;
+ remote-endpoint = <&mipi_csi2_in>;
+ };
+ };
+ port at 2 {
+ reg = <2>;
+
+ ep2: endpoint {
+ bus-width = <8>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ remote-endpoint = <¶llel_out>;
+ };
+ };
+ };
+ };
+ };
+
+...
--
2.35.1
More information about the linux-arm-kernel
mailing list