[PATCH v8 2/2] phy: freescale: imx8m-pcie: Add i.MX8MP PCIe PHY support
Hongxing Zhu
hongxing.zhu at nxp.com
Sun Sep 25 22:11:25 PDT 2022
Hi Vinod:
> -----Original Message-----
> From: Vinod Koul <vkoul at kernel.org>
> Sent: 2022年9月24日 15:33
> To: Hongxing Zhu <hongxing.zhu at nxp.com>
> Cc: p.zabel at pengutronix.de; l.stach at pengutronix.de; bhelgaas at google.com;
> lorenzo.pieralisi at arm.com; robh at kernel.org; shawnguo at kernel.org;
> alexander.stein at ew.tq-group.com; marex at denx.de; richard.leitner at linux.dev;
> linux-phy at lists.infradead.org; devicetree at vger.kernel.org;
> linux-pci at vger.kernel.org; linux-arm-kernel at lists.infradead.org;
> linux-kernel at vger.kernel.org; kernel at pengutronix.de; dl-linux-imx
> <linux-imx at nxp.com>
> Subject: Re: [PATCH v8 2/2] phy: freescale: imx8m-pcie: Add i.MX8MP PCIe
> PHY support
>
> On 20-09-22, 15:38, Richard Zhu wrote:
> > Add i.MX8MP PCIe PHY support.
> >
> > Signed-off-by: Richard Zhu <hongxing.zhu at nxp.com>
> > Signed-off-by: Lucas Stach <l.stach at pengutronix.de>
> > Tested-by: Marek Vasut <marex at denx.de>
> > Tested-by: Richard Leitner <richard.leitner at skidata.com>
> > Tested-by: Alexander Stein <alexander.stein at ew.tq-group.com>
> > Reviewed-by: Lucas Stach <l.stach at pengutronix.de>
> > ---
> > drivers/phy/freescale/phy-fsl-imx8m-pcie.c | 144
> > ++++++++++++++-------
> > 1 file changed, 97 insertions(+), 47 deletions(-)
> >
> > diff --git a/drivers/phy/freescale/phy-fsl-imx8m-pcie.c
> > b/drivers/phy/freescale/phy-fsl-imx8m-pcie.c
> > index ad7d2edfc414..bef0e9d64244 100644
> > --- a/drivers/phy/freescale/phy-fsl-imx8m-pcie.c
> > +++ b/drivers/phy/freescale/phy-fsl-imx8m-pcie.c
> > @@ -11,6 +11,9 @@
> > #include <linux/mfd/syscon.h>
> > #include <linux/mfd/syscon/imx7-iomuxc-gpr.h>
> > #include <linux/module.h>
> > +#include <linux/of_address.h>
> > +#include <linux/of_device.h>
> > +#include <linux/of_device.h>
>
> why do you need all these headers..?
Thanks for your review comments.
Sorry, forget to clean up them from the v1 series.
Only #include <linux/of_device.h> is needed.
>
> > #include <linux/phy/phy.h>
> > #include <linux/platform_device.h>
> > #include <linux/regmap.h>
> > @@ -31,12 +34,10 @@
> > #define IMX8MM_PCIE_PHY_CMN_REG065 0x194
> > #define ANA_AUX_RX_TERM (BIT(7) | BIT(4))
> > #define ANA_AUX_TX_LVL GENMASK(3, 0)
> > -#define IMX8MM_PCIE_PHY_CMN_REG75 0x1D4
> > -#define PCIE_PHY_CMN_REG75_PLL_DONE 0x3
> > +#define IMX8MM_PCIE_PHY_CMN_REG075 0x1D4
>
> why this change?
To keep align with the format of the other PHY CMN registers.
Change the "IMX8MM_PCIE_PHY_CMN_REG75" to
"IMX8MM_PCIE_PHY_CMN_REG075".
Would encapsulate them into one standalone patch later.
>
> > +#define ANA_PLL_DONE 0x3
> > #define PCIE_PHY_TRSV_REG5 0x414
> > -#define PCIE_PHY_TRSV_REG5_GEN1_DEEMP 0x2D
> > #define PCIE_PHY_TRSV_REG6 0x418
> > -#define PCIE_PHY_TRSV_REG6_GEN2_DEEMP 0xF
> >
> > #define IMX8MM_GPR_PCIE_REF_CLK_SEL GENMASK(25, 24)
> > #define IMX8MM_GPR_PCIE_REF_CLK_PLL
> FIELD_PREP(IMX8MM_GPR_PCIE_REF_CLK_SEL, 0x3)
> > @@ -47,16 +48,28 @@
> > #define IMX8MM_GPR_PCIE_SSC_EN BIT(16)
> > #define IMX8MM_GPR_PCIE_AUX_EN_OVERRIDE BIT(9)
> >
> > +enum imx8_pcie_phy_type {
> > + IMX8MM,
> > + IMX8MP,
> > +};
> > +
> > +struct imx8_pcie_phy_drvdata {
> > + enum imx8_pcie_phy_type variant;
> > + const char *gpr;
> > +};
> > +
> > struct imx8_pcie_phy {
> > void __iomem *base;
> > struct clk *clk;
> > struct phy *phy;
> > struct regmap *iomuxc_gpr;
> > struct reset_control *reset;
> > + struct reset_control *perst;
> > u32 refclk_pad_mode;
> > u32 tx_deemph_gen1;
> > u32 tx_deemph_gen2;
> > bool clkreq_unused;
> > + const struct imx8_pcie_phy_drvdata *drvdata;
> > };
> >
> > static int imx8_pcie_phy_init(struct phy *phy) @@ -68,31 +81,20 @@
> > static int imx8_pcie_phy_init(struct phy *phy)
> > reset_control_assert(imx8_phy->reset);
> >
> > pad_mode = imx8_phy->refclk_pad_mode;
> > - /* Set AUX_EN_OVERRIDE 1'b0, when the CLKREQ# isn't hooked */
> > - regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
> > - IMX8MM_GPR_PCIE_AUX_EN_OVERRIDE,
> > - imx8_phy->clkreq_unused ?
> > - 0 : IMX8MM_GPR_PCIE_AUX_EN_OVERRIDE);
> > - regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
> > - IMX8MM_GPR_PCIE_AUX_EN,
> > - IMX8MM_GPR_PCIE_AUX_EN);
> > - regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
> > - IMX8MM_GPR_PCIE_POWER_OFF, 0);
> > - regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
> > - IMX8MM_GPR_PCIE_SSC_EN, 0);
> > -
> > - regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
> > - IMX8MM_GPR_PCIE_REF_CLK_SEL,
> > - pad_mode == IMX8_PCIE_REFCLK_PAD_INPUT ?
> > - IMX8MM_GPR_PCIE_REF_CLK_EXT :
> > - IMX8MM_GPR_PCIE_REF_CLK_PLL);
> > - usleep_range(100, 200);
> > -
> > - /* Do the PHY common block reset */
> > - regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
> > - IMX8MM_GPR_PCIE_CMN_RST,
> > - IMX8MM_GPR_PCIE_CMN_RST);
> > - usleep_range(200, 500);
> > + switch (imx8_phy->drvdata->variant) {
> > + case IMX8MM:
> > + /* Tune PHY de-emphasis setting to pass PCIe compliance. */
> > + if (imx8_phy->tx_deemph_gen1)
> > + writel(imx8_phy->tx_deemph_gen1,
> > + imx8_phy->base + PCIE_PHY_TRSV_REG5);
> > + if (imx8_phy->tx_deemph_gen2)
> > + writel(imx8_phy->tx_deemph_gen2,
> > + imx8_phy->base + PCIE_PHY_TRSV_REG6);
> > + break;
> > + case IMX8MP:
> > + reset_control_assert(imx8_phy->perst);
> > + break;
> > + }
> >
> > if (pad_mode == IMX8_PCIE_REFCLK_PAD_INPUT ||
> > pad_mode == IMX8_PCIE_REFCLK_PAD_UNUSED) { @@ -120,20
> +122,44 @@
> > static int imx8_pcie_phy_init(struct phy *phy)
> > imx8_phy->base + IMX8MM_PCIE_PHY_CMN_REG065);
> > }
> >
> > - /* Tune PHY de-emphasis setting to pass PCIe compliance. */
> > - if (imx8_phy->tx_deemph_gen1)
> > - writel(imx8_phy->tx_deemph_gen1,
> > - imx8_phy->base + PCIE_PHY_TRSV_REG5);
> > - if (imx8_phy->tx_deemph_gen2)
> > - writel(imx8_phy->tx_deemph_gen2,
> > - imx8_phy->base + PCIE_PHY_TRSV_REG6);
> > + /* Set AUX_EN_OVERRIDE 1'b0, when the CLKREQ# isn't hooked */
> > + regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
> > + IMX8MM_GPR_PCIE_AUX_EN_OVERRIDE,
> > + imx8_phy->clkreq_unused ?
> > + 0 : IMX8MM_GPR_PCIE_AUX_EN_OVERRIDE);
> > + regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
> > + IMX8MM_GPR_PCIE_AUX_EN,
> > + IMX8MM_GPR_PCIE_AUX_EN);
> > + regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
> > + IMX8MM_GPR_PCIE_POWER_OFF, 0);
> > + regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
> > + IMX8MM_GPR_PCIE_SSC_EN, 0);
> > +
> > + regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
> > + IMX8MM_GPR_PCIE_REF_CLK_SEL,
> > + pad_mode == IMX8_PCIE_REFCLK_PAD_INPUT ?
> > + IMX8MM_GPR_PCIE_REF_CLK_EXT :
> > + IMX8MM_GPR_PCIE_REF_CLK_PLL);
>
> Lets do code reorg in a separate patch and then add support for new SOC, that
> is more reviewable that this big pile of changes
Okay, would spilt them into two patches.
Thanks.
Richard Zhu
Best Regards
>
> > + usleep_range(100, 200);
> >
> > - reset_control_deassert(imx8_phy->reset);
> > + /* Do the PHY common block reset */
> > + regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
> > + IMX8MM_GPR_PCIE_CMN_RST,
> > + IMX8MM_GPR_PCIE_CMN_RST);
> > +
> > + switch (imx8_phy->drvdata->variant) {
> > + case IMX8MP:
> > + reset_control_deassert(imx8_phy->perst);
> > + fallthrough;
> > + case IMX8MM:
> > + reset_control_deassert(imx8_phy->reset);
> > + usleep_range(200, 500);
> > + break;
> > + }
> >
> > /* Polling to check the phy is ready or not. */
> > - ret = readl_poll_timeout(imx8_phy->base +
> IMX8MM_PCIE_PHY_CMN_REG75,
> > - val, val == PCIE_PHY_CMN_REG75_PLL_DONE,
> > - 10, 20000);
> > + ret = readl_poll_timeout(imx8_phy->base +
> IMX8MM_PCIE_PHY_CMN_REG075,
> > + val, val == ANA_PLL_DONE, 10, 20000);
> > return ret;
> > }
> >
> > @@ -160,6 +186,25 @@ static const struct phy_ops imx8_pcie_phy_ops = {
> > .owner = THIS_MODULE,
> > };
> >
> > +static const struct imx8_pcie_phy_drvdata drvdata[] = {
> > + [IMX8MM] = {
> > + .variant = IMX8MM,
> > + .gpr = "fsl,imx8mm-iomuxc-gpr",
> > + },
> > +
> > + [IMX8MP] = {
> > + .variant = IMX8MP,
> > + .gpr = "fsl,imx8mp-iomuxc-gpr",
> > + },
> > +};
> > +
> > +static const struct of_device_id imx8_pcie_phy_of_match[] = {
> > + {.compatible = "fsl,imx8mm-pcie-phy", .data = &drvdata[IMX8MM], },
> > + {.compatible = "fsl,imx8mp-pcie-phy", .data = &drvdata[IMX8MP], },
> > + { },
> > +};
> > +MODULE_DEVICE_TABLE(of, imx8_pcie_phy_of_match);
> > +
> > static int imx8_pcie_phy_probe(struct platform_device *pdev) {
> > struct phy_provider *phy_provider;
> > @@ -172,6 +217,8 @@ static int imx8_pcie_phy_probe(struct
> platform_device *pdev)
> > if (!imx8_phy)
> > return -ENOMEM;
> >
> > + imx8_phy->drvdata = of_device_get_match_data(dev);
> > +
> > /* get PHY refclk pad mode */
> > of_property_read_u32(np, "fsl,refclk-pad-mode",
> > &imx8_phy->refclk_pad_mode);
> > @@ -197,7 +244,7 @@ static int imx8_pcie_phy_probe(struct
> > platform_device *pdev)
> >
> > /* Grab GPR config register range */
> > imx8_phy->iomuxc_gpr =
> > - syscon_regmap_lookup_by_compatible("fsl,imx6q-iomuxc-gpr");
> > + syscon_regmap_lookup_by_compatible(imx8_phy->drvdata->gpr);
> > if (IS_ERR(imx8_phy->iomuxc_gpr)) {
> > dev_err(dev, "unable to find iomuxc registers\n");
> > return PTR_ERR(imx8_phy->iomuxc_gpr); @@ -209,6 +256,15 @@
> static
> > int imx8_pcie_phy_probe(struct platform_device *pdev)
> > return PTR_ERR(imx8_phy->reset);
> > }
> >
> > + if (imx8_phy->drvdata->variant == IMX8MP) {
> > + imx8_phy->perst =
> > + devm_reset_control_get_exclusive(dev, "perst");
> > + if (IS_ERR(imx8_phy->perst)) {
> > + dev_err(dev, "Failed to get PCIE PHY PERST control\n");
> > + return PTR_ERR(imx8_phy->perst);
> > + }
> > + }
> > +
> > res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > imx8_phy->base = devm_ioremap_resource(dev, res);
> > if (IS_ERR(imx8_phy->base))
> > @@ -225,12 +281,6 @@ static int imx8_pcie_phy_probe(struct
> platform_device *pdev)
> > return PTR_ERR_OR_ZERO(phy_provider); }
> >
> > -static const struct of_device_id imx8_pcie_phy_of_match[] = {
> > - {.compatible = "fsl,imx8mm-pcie-phy",},
> > - { },
> > -};
> > -MODULE_DEVICE_TABLE(of, imx8_pcie_phy_of_match);
> > -
> > static struct platform_driver imx8_pcie_phy_driver = {
> > .probe = imx8_pcie_phy_probe,
> > .driver = {
> > --
> > 2.25.1
>
> --
> ~Vinod
More information about the linux-arm-kernel
mailing list