[PATCH v2 5/9] arm64: dts: ls1046a: make dma-coherent global to the SoC

[Sean Anderson]

On 9/23/22 12:26 PM, Leo Li wrote:
> 
> 
>> -----Original Message-----
>> From: Sean Anderson <sean.anderson at seco.com>
>> Sent: Friday, September 23, 2022 11:11 AM
>> To: Leo Li <leoyang.li at nxp.com>; shawnguo at kernel.org;
>> devicetree at vger.kernel.org
>> Cc: robh+dt at kernel.org; linux-arm-kernel at lists.infradead.org; linux-
>> kernel at vger.kernel.org; Laurentiu Tudor <laurentiu.tudor at nxp.com>
>> Subject: Re: [PATCH v2 5/9] arm64: dts: ls1046a: make dma-coherent global
>> to the SoC
>> 
>> 
>> Hi All,
>> 
>> On 9/15/22 7:34 PM, Li Yang wrote:
>> > These SoCs are really completely dma coherent in their entirety so add
>> > the dma-coherent property at the soc level in the device tree and drop
>> > the instances where it's specifically added to a few select devices.
>> >
>> > Signed-off-by: Laurentiu Tudor <laurentiu.tudor at nxp.com>
>> > Signed-off-by: Li Yang <leoyang.li at nxp.com>
>> > ---
>> >  arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi | 5 +----
>> >  1 file changed, 1 insertion(+), 4 deletions(-)
>> >
>> > diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi
>> > b/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi
>> > index 27033c558e3e..e406499a26b4 100644
>> > --- a/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi
>> > +++ b/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi
>> > @@ -273,6 +273,7 @@ soc: soc {
>> >  		#size-cells = <2>;
>> >  		ranges;
>> >  		dma-ranges = <0x0 0x0 0x0 0x0 0x10000 0x00000000>;
>> > +		dma-coherent;
>> >
>> >  		ddr: memory-controller at 1080000 {
>> >  			compatible = "fsl,qoriq-memory-controller"; @@ -
>> 355,7 +356,6 @@
>> > crypto: crypto at 1700000 {
>> >  			ranges = <0x0 0x00 0x1700000 0x100000>;
>> >  			reg = <0x00 0x1700000 0x0 0x100000>;
>> >  			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
>> > -			dma-coherent;
>> >
>> >  			sec_jr0: jr at 10000 {
>> >  				compatible = "fsl,sec-v5.4-job-ring", @@ -
>> 794,7 +794,6 @@ pcie1:
>> > pcie at 3400000 {
>> >  			#address-cells = <3>;
>> >  			#size-cells = <2>;
>> >  			device_type = "pci";
>> > -			dma-coherent;
>> >  			num-viewport = <8>;
>> >  			bus-range = <0x0 0xff>;
>> >  			ranges = <0x81000000 0x0 0x00000000 0x40
>> 0x00010000 0x0 0x00010000   /* downstream I/O */
>> > @@ -834,7 +833,6 @@ pcie2: pcie at 3500000 {
>> >  			#address-cells = <3>;
>> >  			#size-cells = <2>;
>> >  			device_type = "pci";
>> > -			dma-coherent;
>> >  			num-viewport = <8>;
>> >  			bus-range = <0x0 0xff>;
>> >  			ranges = <0x81000000 0x0 0x00000000 0x48
>> 0x00010000 0x0 0x00010000   /* downstream I/O */
>> > @@ -874,7 +872,6 @@ pcie3: pcie at 3600000 {
>> >  			#address-cells = <3>;
>> >  			#size-cells = <2>;
>> >  			device_type = "pci";
>> > -			dma-coherent;
>> >  			num-viewport = <8>;
>> >  			bus-range = <0x0 0xff>;
>> >  			ranges = <0x81000000 0x0 0x00000000 0x50
>> 0x00010000 0x0 0x00010000   /* downstream I/O */
>> >
>> 
>> I'd like to summarize the conclusions of [1] below. This patch breaks I2C0,
>> which is the only user of eDMA at the moment. eDMA is noncoherent
>> because snooping is not enabled for it. I have submitted a patch [2] to U-
>> Boot to enable snooping for eDMA. For now, this patch must add dma-
>> noncoherent to the i2c0 node.
> 
> I have sent a V3 yesterday to set dma-noncoherent on edma node.  But are you saying that the dma-noncoherent need to be added to the i2c node to make it work?

I believe dma coherency is a property of the consumer, not the provider. See
e.g. really_probe/platform_dma_configure/of_dma_configure/of_dma_is_coherent.

> For the u-boot patch, I will check with the hardware team to see if it is safe to set the reserved bit for edma snooping.

Thanks. I'm curious as to whether this omission is intentional or not.

> There is a problem with this is that it breaks the i2c for older u-boot.  Probably the best way is to make the default to be non-coherent in dts and update it in u-boot when snooping is enabled?

Yes, that is what I propose.

--Sean