[PATCH v4 2/2] ARM: dts: aspeed: Add AMD DaytonaX BMC
Konstantin Aladyshev
aladyshev22 at gmail.com
Wed Sep 21 14:15:07 PDT 2022
Sorry, I still have some questions, can you please help me?
I work with kernel in the context of the OpenBMC project, and it is
not possible to run 'make dtbs_check' in the linux kernel devshell
(Yocto). So I've tried to download upstream kernel and have performed
the following commands to make the dtbs_check:
```
$ make ARCH=arm aspeed_g5_defconfig && make ARCH=arm dtbs_check
```
This gave me a ton of output regarding all the problems in all of the
aspeed boards. 'wc -l' says that the log file is about 7080 lines
long. Is it possible to get the output only for my target DTS? The
article that you've referred to
(https://www.kernel.org/doc/Documentation/devicetree/writing-schema.rst)
only have the information about how to run checks against one schema
(DT_SCHEMA_FILES), but it is not the same thing.
I've manually tried to split the output regarding my DTS file, but
even so the output is overwhelming - https://pastebin.com/b92rnBt0. I
just don't understand if the mentioned things are about the common
"aspeed-g5.dtsi" file that I should ignore or the things regarding
errors in my submitted DTS file. Can you give me some advice on that?
Anyway I think I've updated my patchset regarding all the things that
you've mentioned explicitly. I've split the patchset to two as you've
requested and have added a cover letter. I hope I did everything
correctly.
But I'm still not sure about this 'make dtbs_check'. If I did
something wrong, please correct me.
Best regards,
Konstantin Aladyshev
On Thu, Sep 22, 2022 at 12:10 AM Konstantin Aladyshev
<aladyshev22 at gmail.com> wrote:
>
> Add initial version of device tree for the BMC in the AMD DaytonaX
> platform.
>
> AMD DaytonaX platform is a customer reference board (CRB) with an
> Aspeed ast2500 BMC manufactured by AMD.
>
> Signed-off-by: Konstantin Aladyshev <aladyshev22 at gmail.com>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/aspeed-bmc-amd-daytonax.dts | 319 ++++++++++++++++++
> 2 files changed, 320 insertions(+)
> create mode 100644 arch/arm/boot/dts/aspeed-bmc-amd-daytonax.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 05d8aef6e5d2..d81fe7ef5475 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1574,6 +1574,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
> aspeed-ast2500-evb.dtb \
> aspeed-ast2600-evb-a1.dtb \
> aspeed-ast2600-evb.dtb \
> + aspeed-bmc-amd-daytonax.dtb \
> aspeed-bmc-amd-ethanolx.dtb \
> aspeed-bmc-ampere-mtjade.dtb \
> aspeed-bmc-arm-stardragon4800-rep2.dtb \
> diff --git a/arch/arm/boot/dts/aspeed-bmc-amd-daytonax.dts b/arch/arm/boot/dts/aspeed-bmc-amd-daytonax.dts
> new file mode 100644
> index 000000000000..64bb9bf92de2
> --- /dev/null
> +++ b/arch/arm/boot/dts/aspeed-bmc-amd-daytonax.dts
> @@ -0,0 +1,319 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/dts-v1/;
> +
> +#include "aspeed-g5.dtsi"
> +#include <dt-bindings/gpio/aspeed-gpio.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +
> +/ {
> + model = "AMD DaytonaX BMC";
> + compatible = "amd,daytonax-bmc", "aspeed,ast2500";
> +
> + memory at 80000000 {
> + reg = <0x80000000 0x20000000>;
> + };
> +
> + reserved-memory {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + video_engine_memory: jpegbuffer {
> + size = <0x02000000>; /* 32M */
> + alignment = <0x01000000>;
> + compatible = "shared-dma-pool";
> + reusable;
> + };
> + };
> +
> + aliases {
> + serial0 = &uart1;
> + serial4 = &uart5;
> + };
> +
> + chosen {
> + stdout-path = &uart5;
> + bootargs = "console=ttyS4,115200";
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + led-fault {
> + gpios = <&gpio ASPEED_GPIO(A, 2) GPIO_ACTIVE_LOW>;
> + };
> +
> + led-identify {
> + gpios = <&gpio ASPEED_GPIO(A, 3) GPIO_ACTIVE_LOW>;
> + };
> + };
> +
> + iio-hwmon {
> + compatible = "iio-hwmon";
> + io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>, <&adc 4>,
> + <&adc 5>, <&adc 6>, <&adc 7>, <&adc 8>, <&adc 9>,
> + <&adc 10>, <&adc 11>, <&adc 12>, <&adc 13>, <&adc 14>,
> + <&adc 15>;
> + };
> +};
> +
> +&fmc {
> + status = "okay";
> + flash at 0 {
> + status = "okay";
> + m25p,fast-read;
> + label = "bmc";
> + #include "openbmc-flash-layout.dtsi"
> + };
> +};
> +
> +&mac0 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_rgmii1_default &pinctrl_mdio1_default>;
> +};
> +
> +&uart1 {
> + //Host Console
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_txd1_default
> + &pinctrl_rxd1_default
> + &pinctrl_nrts1_default
> + &pinctrl_ndtr1_default
> + &pinctrl_ndsr1_default
> + &pinctrl_ncts1_default
> + &pinctrl_ndcd1_default
> + &pinctrl_nri1_default>;
> +};
> +
> +&uart5 {
> + //BMC Console
> + status = "okay";
> +};
> +
> +&vuart {
> + status = "okay";
> + aspeed,lpc-io-reg = <0x3f8>;
> + aspeed,lpc-interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&adc {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_adc0_default
> + &pinctrl_adc1_default
> + &pinctrl_adc2_default
> + &pinctrl_adc3_default
> + &pinctrl_adc4_default
> + &pinctrl_adc5_default
> + &pinctrl_adc6_default
> + &pinctrl_adc7_default
> + &pinctrl_adc8_default
> + &pinctrl_adc9_default
> + &pinctrl_adc10_default
> + &pinctrl_adc11_default
> + &pinctrl_adc12_default
> + &pinctrl_adc13_default
> + &pinctrl_adc14_default
> + &pinctrl_adc15_default>;
> +};
> +
> +&gpio {
> + status = "okay";
> + gpio-line-names =
> + /*A0-A7*/ "","","led-fault","led-identify","","","","",
> + /*B0-B7*/ "","","","","","","","",
> + /*C0-C7*/ "id-button","","","","","","","",
> + /*D0-D7*/ "","","ASSERT_BMC_READY","","","","","",
> + /*E0-E7*/ "reset-button","reset-control","power-button","power-control","",
> + "power-good","power-ok","",
> + /*F0-F7*/ "","","","","","","BATTERY_DETECT","",
> + /*G0-G7*/ "","","","","","","","",
> + /*H0-H7*/ "","","","","","","","",
> + /*I0-I7*/ "","","","","","","","",
> + /*J0-J7*/ "","","","","","","","",
> + /*K0-K7*/ "","","","","","","","",
> + /*L0-L7*/ "","","","","","","","",
> + /*M0-M7*/ "","","","","","","","",
> + /*N0-N7*/ "","","","","","","","",
> + /*O0-O7*/ "","","","","","","","",
> + /*P0-P7*/ "","","","","","","","",
> + /*Q0-Q7*/ "","","","","","","","",
> + /*R0-R7*/ "","","","","","","","",
> + /*S0-S7*/ "","","","","","","","",
> + /*T0-T7*/ "","","","","","","","",
> + /*U0-U7*/ "","","","","","","","",
> + /*V0-V7*/ "","","","","","","","",
> + /*W0-W7*/ "","","","","","","","",
> + /*X0-X7*/ "","","","","","","","",
> + /*Y0-Y7*/ "","","","","","","","",
> + /*Z0-Z7*/ "","","","","","","","",
> + /*AA0-AA7*/ "","","","","","","","",
> + /*AB0-AB7*/ "FM_BMC_READ_SPD_TEMP","","","","","","","",
> + /*AC0-AC7*/ "","","","","","","","";
> +};
> +
> +&i2c0 {
> + status = "okay";
> +};
> +
> +&i2c1 {
> + status = "okay";
> +};
> +
> +&i2c2 {
> + status = "okay";
> +};
> +
> +&i2c3 {
> + status = "okay";
> +};
> +
> +&i2c4 {
> + status = "okay";
> +};
> +
> +&i2c5 {
> + status = "okay";
> +};
> +
> +&i2c6 {
> + status = "okay";
> +};
> +
> +&i2c7 {
> + status = "okay";
> +};
> +
> +&i2c8 {
> + status = "okay";
> +};
> +
> +&i2c10 {
> + status = "okay";
> +};
> +
> +&i2c11 {
> + status = "okay";
> +};
> +
> +&i2c12 {
> + status = "okay";
> +};
> +
> +&kcs3 {
> + status = "okay";
> + aspeed,lpc-io-reg = <0xca2>;
> +};
> +
> +&lpc_snoop {
> + status = "okay";
> + snoop-ports = <0x80>, <0x81>;
> +};
> +
> +&lpc_ctrl {
> + status = "okay";
> +};
> +
> +&pwm_tacho {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm0_default
> + &pinctrl_pwm1_default
> + &pinctrl_pwm2_default
> + &pinctrl_pwm3_default
> + &pinctrl_pwm4_default
> + &pinctrl_pwm5_default
> + &pinctrl_pwm6_default
> + &pinctrl_pwm7_default>;
> +
> + fan at 0 {
> + reg = <0x00>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x00>;
> + };
> +
> + fan at 1 {
> + reg = <0x00>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x01>;
> + };
> +
> + fan at 2 {
> + reg = <0x01>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x02>;
> + };
> +
> + fan at 3 {
> + reg = <0x01>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x03>;
> + };
> +
> + fan at 4 {
> + reg = <0x02>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x04>;
> + };
> +
> + fan at 5 {
> + reg = <0x02>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x05>;
> + };
> +
> + fan at 6 {
> + reg = <0x03>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x06>;
> + };
> +
> + fan at 7 {
> + reg = <0x03>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x07>;
> + };
> +
> + fan at 8 {
> + reg = <0x04>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x08>;
> + };
> +
> + fan at 9 {
> + reg = <0x04>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x09>;
> + };
> +
> + fan at 10 {
> + reg = <0x05>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x0a>;
> + };
> +
> + fan at 11 {
> + reg = <0x05>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x0b>;
> + };
> +
> + fan at 12 {
> + reg = <0x06>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x0c>;
> + };
> +
> + fan at 13 {
> + reg = <0x06>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x0d>;
> + };
> +
> + fan at 14 {
> + reg = <0x07>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x0e>;
> + };
> +
> + fan at 15 {
> + reg = <0x07>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x0f>;
> + };
> +};
> +
> +&video {
> + status = "okay";
> + memory-region = <&video_engine_memory>;
> +};
> +
> +&vhub {
> + status = "okay";
> +};
> --
> 2.25.1
>
More information about the linux-arm-kernel
mailing list