[PATCH] Changes phy configuration to expose sata in place of usb3 on quartz64-a board

[Krzysztof Kozlowski]

On 14/09/2022 20:59, Alessandro Carminati wrote:
> The Quartz64 board is built upon Rockchip RK3566.
> Rockchip RK3566 has two combo phys.
> The first connects USB3 and SATA ctrl1, and the second PCIe lane and SATA
> ctrl2.
> The second combo phy is hardwired to the PCIe slot, where for the first,
> the hardware on the board provides both the USB3 connector and the SATA
> connector.
> This DT allows the users to switch the combo phy to the SATA connector.
> 
> Signed-off-by: Alessandro Carminati <alessandro.carminati at gmail.com>
> ---
>  .../dts/rockchip/rk3566-quartz64-a.sata.dts   | 839 ++++++++++++++++++
>  1 file changed, 839 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.sata.dts
> 
> diff --git a/arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.sata.dts b/arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.sata.dts
> new file mode 100644
> index 000000000000..6ac21b729be7
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.sata.dts
> @@ -0,0 +1,839 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/pinctrl/rockchip.h>
> +#include <dt-bindings/soc/rockchip,vop2.h>
> +#include "rk3566.dtsi"
> +
> +/ {
> +	model = "Pine64 RK3566 Quartz64-A Board";
> +	compatible = "pine64,quartz64-a", "rockchip,rk3566";
> +
> +	aliases {
> +		ethernet0 = &gmac1;
> +		mmc0 = &sdmmc0;
> +		mmc1 = &sdhci;
> +	};
> +
> +	chosen: chosen {
> +		stdout-path = "serial2:1500000n8";
> +	};
> +
> +	gmac1_clkin: external-gmac1-clock {
> +		compatible = "fixed-clock";
> +		clock-frequency = <125000000>;
> +		clock-output-names = "gmac1_clkin";
> +		#clock-cells = <0>;
> +	};
> +
> +	fan: gpio_fan {

No underscores in node names. Node name just "fan"

> +		compatible = "gpio-fan";
> +		gpios = <&gpio0 RK_PD5 GPIO_ACTIVE_HIGH>;
> +		gpio-fan,speed-map = <0    0
> +				      4500 1>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&fan_en_h>;
> +		#cooling-cells = <2>;
> +	};
> +
> +	hdmi-con {

Node name: connector

> +		compatible = "hdmi-connector";
> +		type = "a";
> +
> +		port {
> +			hdmi_con_in: endpoint {
> +				remote-endpoint = <&hdmi_out_con>;
> +			};
> +		};
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +
> +		led-work {
> +			label = "work-led";
> +			default-state = "off";
> +			gpios = <&gpio0 RK_PD3 GPIO_ACTIVE_HIGH>;
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&work_led_enable_h>;
> +			retain-state-suspended;
> +		};
> +
> +		led-diy {
> +			label = "diy-led";
> +			default-state = "on";
> +			gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>;
> +			linux,default-trigger = "heartbeat";
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&diy_led_enable_h>;
> +			retain-state-suspended;
> +		};
> +	};
> +
> +	rk817-sound {
> +		compatible = "simple-audio-card";
> +		simple-audio-card,format = "i2s";
> +		simple-audio-card,name = "Analog RK817";
> +		simple-audio-card,mclk-fs = <256>;
> +
> +		simple-audio-card,cpu {
> +			sound-dai = <&i2s1_8ch>;
> +		};
> +
> +		simple-audio-card,codec {
> +			sound-dai = <&rk817>;
> +		};
> +	};
> +
> +	sdio_pwrseq: sdio-pwrseq {
> +		compatible = "mmc-pwrseq-simple";
> +		clocks = <&rk817 1>;
> +		clock-names = "ext_clock";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&wifi_enable_h>;
> +		post-power-on-delay-ms = <100>;
> +		power-off-delay-us = <5000000>;
> +		reset-gpios = <&gpio2 RK_PC2 GPIO_ACTIVE_LOW>;
> +	};
> +
> +	spdif_dit: spdif-dit {
> +		compatible = "linux,spdif-dit";
> +		#sound-dai-cells = <0>;
> +	};
> +
> +	spdif_sound: spdif-sound {
> +		compatible = "simple-audio-card";
> +		simple-audio-card,name = "SPDIF";
> +
> +		simple-audio-card,cpu {
> +			sound-dai = <&spdif>;
> +		};
> +
> +		simple-audio-card,codec {
> +			sound-dai = <&spdif_dit>;
> +		};
> +	};
> +
> +	vcc12v_dcin: vcc12v_dcin {

No underscores in node names, generic node name, so at least with
regulator prefix or suffix.

> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc12v_dcin";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <12000000>;
> +		regulator-max-microvolt = <12000000>;
> +	};
> +
> +	/* vbus feeds the rk817 usb input.
> +	 * With no battery attached, also feeds vcc_bat+
> +	 * via ON/OFF_BAT jumper
> +	 */
> +	vbus: vbus {

Ditto

> +		compatible = "regulator-fixed";
> +		regulator-name = "vbus";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		vin-supply = <&vcc12v_dcin>;
> +	};
> +
> +	vcc3v3_pcie_p: vcc3v3-pcie-p-regulator {

And here you have suffix...

> +		compatible = "regulator-fixed";
> +		enable-active-high;
> +		gpio = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pcie_enable_h>;
> +		regulator-name = "vcc3v3_pcie_p";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		vin-supply = <&vcc_3v3>;
> +	};
> +
> +	vcc5v0_usb: vcc5v0_usb {

Ditto

> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc5v0_usb";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		vin-supply = <&vcc12v_dcin>;
> +	};
> +
> +	/* all four ports are controlled by one gpio
> +	 * the host ports are sourced from vcc5v0_usb
> +	 * the otg port is sourced from vcc5v0_midu
> +	 */
> +	vcc5v0_usb20_host: vcc5v0_usb20_host {

and in other places as well



> +		compatible = "regulator-fixed";
> +		enable-active-high;
> +		gpio = <&gpio4 RK_PB5 GPIO_ACTIVE_HIGH>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&vcc5v0_usb20_host_en>;
> +		regulator-name = "vcc5v0_usb20_host";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		vin-supply = <&vcc5v0_usb>;
> +	};
> +
> +	vcc5v0_usb20_otg: vcc5v0_usb20_otg {
> +		compatible = "regulator-fixed";
> +		enable-active-high;
> +		gpio = <&gpio4 RK_PB5 GPIO_ACTIVE_HIGH>;
> +		regulator-name = "vcc5v0_usb20_otg";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		vin-supply = <&dcdc_boost>;
> +	};
> +
> +	vcc3v3_sd: vcc3v3_sd {
> +		compatible = "regulator-fixed";
> +		enable-active-low;
> +		gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&vcc_sd_h>;
> +		regulator-boot-on;
> +		regulator-name = "vcc3v3_sd";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		vin-supply = <&vcc_3v3>;
> +	};
> +
> +	/* sourced from vbus and vcc_bat+ via rk817 sw5 */
> +	vcc_sys: vcc_sys {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc_sys";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <4400000>;
> +		regulator-max-microvolt = <4400000>;
> +		vin-supply = <&vbus>;
> +	};
> +
> +	/* sourced from vcc_sys, sdio module operates internally at 3.3v */
> +	vcc_wl: vcc_wl {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc_wl";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		vin-supply = <&vcc_sys>;
> +	};
> +};
> +
> +&combphy1 {
> +	status = "okay";
> +};
> +
> +&combphy2 {
> +	status = "okay";
> +};
> +
> +&cpu0 {
> +	cpu-supply = <&vdd_cpu>;
> +};
> +
> +&cpu1 {
> +	cpu-supply = <&vdd_cpu>;
> +};
> +
> +&cpu2 {
> +	cpu-supply = <&vdd_cpu>;
> +};
> +
> +&cpu3 {
> +	cpu-supply = <&vdd_cpu>;
> +};
> +
> +&cpu_thermal {
> +	trips {
> +		cpu_hot: cpu_hot {

No underscores in node names. Are you sure bindings/schema do not expect
some specific name?

> +			temperature = <55000>;
> +			hysteresis = <2000>;
> +			type = "active";
> +		};
> +	};


Best regards,
Krzysztof