[PATCH v2 5/7] spi: spi-zynqmp-gqspi: Add tap delay support for ZynqMP GQSPI Controller

[Amit Kumar Mahapatra]

From: Naga Sureshkumar Relli <nagasure at xilinx.com>

GQSPI controller uses the internal clock for loopback mode. The loopback
mode is used with the high-speed Quad SPI timing mode, where the memory
interface clock needs to be greater than 40 MHz. Based on the tap delay
value programmed, the internal clock is delayed and used for capturing
the data.
Based upon the frequency of operation this patch sets the recommended
tap delay values.

Signed-off-by: Naga Sureshkumar Relli <nagasure at xilinx.com>
Signed-off-by: Michal Simek <michal.simek at amd.com>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra at xilinx.com>
---
 drivers/spi/spi-zynqmp-gqspi.c | 48 +++++++++++++++++++++++++++++++---
 1 file changed, 44 insertions(+), 4 deletions(-)

diff --git a/drivers/spi/spi-zynqmp-gqspi.c b/drivers/spi/spi-zynqmp-gqspi.c
index 024085098515..0e6423ff33f4 100644
--- a/drivers/spi/spi-zynqmp-gqspi.c
+++ b/drivers/spi/spi-zynqmp-gqspi.c
@@ -48,6 +48,7 @@
 #define GQSPI_QSPIDMA_DST_I_MASK_OFST	0x00000820
 #define GQSPI_QSPIDMA_DST_ADDR_OFST	0x00000800
 #define GQSPI_QSPIDMA_DST_ADDR_MSB_OFST 0x00000828
+#define GQSPI_DATA_DLY_ADJ_OFST         0x000001F8
 
 /* GQSPI register bit masks */
 #define GQSPI_SEL_MASK				0x00000001
@@ -133,6 +134,15 @@
 #define GQSPI_SELECT_MODE_QUADSPI	0x4
 #define GQSPI_DMA_UNALIGN		0x3
 #define GQSPI_DEFAULT_NUM_CS	1	/* Default number of chip selects */
+#define GQSPI_USE_DATA_DLY              0x1
+#define GQSPI_USE_DATA_DLY_SHIFT        31
+#define GQSPI_DATA_DLY_ADJ_VALUE        0x2
+#define GQSPI_DATA_DLY_ADJ_SHIFT        28
+
+#define GQSPI_FREQ_37_5MHZ      37500000
+#define GQSPI_FREQ_40MHZ        40000000
+#define GQSPI_FREQ_100MHZ       100000000
+#define GQSPI_FREQ_150MHZ       150000000
 
 #define SPI_AUTOSUSPEND_TIMEOUT		3000
 enum mode_type {GQSPI_MODE_IO, GQSPI_MODE_DMA};
@@ -251,6 +261,37 @@ static void zynqmp_gqspi_selectslave(struct zynqmp_qspi *instanceptr,
 	}
 }
 
+/**
+ * zynqmp_qspi_set_tapdelay:	To configure qspi tap delays
+ * @xqspi:		Pointer to the zynqmp_qspi structure
+ * @baudrateval:	Buadrate to configure
+ */
+static void zynqmp_qspi_set_tapdelay(struct zynqmp_qspi *xqspi, u32 baudrateval)
+{
+	u32 lpbkdlyadj = 0, datadlyadj = 0, clk_rate;
+	u32 reqhz = 0;
+
+	clk_rate = clk_get_rate(xqspi->refclk);
+	reqhz = (clk_rate / (GQSPI_BAUD_DIV_SHIFT << baudrateval));
+
+	if (reqhz <= GQSPI_FREQ_40MHZ) {
+		zynqmp_pm_set_tapdelay_bypass(PM_TAPDELAY_QSPI,
+					      PM_TAPDELAY_BYPASS_ENABLE);
+	} else if (reqhz <= GQSPI_FREQ_100MHZ) {
+		zynqmp_pm_set_tapdelay_bypass(PM_TAPDELAY_QSPI,
+					      PM_TAPDELAY_BYPASS_ENABLE);
+		lpbkdlyadj |= (GQSPI_LPBK_DLY_ADJ_USE_LPBK_MASK);
+		datadlyadj |= ((GQSPI_USE_DATA_DLY <<
+				GQSPI_USE_DATA_DLY_SHIFT)
+				| (GQSPI_DATA_DLY_ADJ_VALUE <<
+					GQSPI_DATA_DLY_ADJ_SHIFT));
+	} else if (reqhz <= GQSPI_FREQ_150MHZ) {
+		lpbkdlyadj |= GQSPI_LPBK_DLY_ADJ_USE_LPBK_MASK;
+	}
+	zynqmp_gqspi_write(xqspi, GQSPI_LPBK_DLY_ADJ_OFST, lpbkdlyadj);
+	zynqmp_gqspi_write(xqspi, GQSPI_DATA_DLY_ADJ_OFST, datadlyadj);
+}
+
 /**
  * zynqmp_qspi_init_hw - Initialize the hardware
  * @xqspi:	Pointer to the zynqmp_qspi structure
@@ -330,16 +371,14 @@ static void zynqmp_qspi_init_hw(struct zynqmp_qspi *xqspi)
 	config_reg |= (baud_rate_val << GQSPI_CFG_BAUD_RATE_DIV_SHIFT);
 
 	zynqmp_gqspi_write(xqspi, GQSPI_CONFIG_OFST, config_reg);
+	/* Set the tapdelay for clock frequency */
+	zynqmp_qspi_set_tapdelay(xqspi, baud_rate_val);
 
 	/* Clear the TX and RX FIFO */
 	zynqmp_gqspi_write(xqspi, GQSPI_FIFO_CTRL_OFST,
 			   GQSPI_FIFO_CTRL_RST_RX_FIFO_MASK |
 			   GQSPI_FIFO_CTRL_RST_TX_FIFO_MASK |
 			   GQSPI_FIFO_CTRL_RST_GEN_FIFO_MASK);
-	/* Set by default to allow for high frequencies */
-	zynqmp_gqspi_write(xqspi, GQSPI_LPBK_DLY_ADJ_OFST,
-			   zynqmp_gqspi_read(xqspi, GQSPI_LPBK_DLY_ADJ_OFST) |
-			   GQSPI_LPBK_DLY_ADJ_USE_LPBK_MASK);
 	/* Reset thresholds */
 	zynqmp_gqspi_write(xqspi, GQSPI_TX_THRESHOLD_OFST,
 			   GQSPI_TX_FIFO_THRESHOLD_RESET_VAL);
@@ -494,6 +533,7 @@ static int zynqmp_qspi_config_op(struct zynqmp_qspi *xqspi,
 		config_reg &= ~GQSPI_CFG_BAUD_RATE_DIV_MASK;
 		config_reg |= (baud_rate_val << GQSPI_CFG_BAUD_RATE_DIV_SHIFT);
 		zynqmp_gqspi_write(xqspi, GQSPI_CONFIG_OFST, config_reg);
+		zynqmp_qspi_set_tapdelay(xqspi, baud_rate_val);
 	}
 	return 0;
 }
-- 
2.25.1