[PATCH v6 2/2] ARM: dts: at91: Adding SAMA5D3-EDS board

[Krzysztof Kozlowski]

On 08/09/2022 16:50, Jerry.Ray at microchip.com wrote:
>>>>> The SAMA5D3-EDS board is an Ethernet Development Platform allowing 
>>>>> for evaluating many Microchip ethernet switch and PHY products.  
>>>>> Various daughter cards can connect up via an RGMII connector or an RMII connector.
>>>>>
>>>>> The EDS board is not intended for stand-alone use and has no 
>>>>> ethernet capabilities when no daughter board is connected.  As such, 
>>>>> this device tree is intended to be used with a DT overlay defining the add-on board.
>>>>> To better ensure consistency, some items are defined here as a form 
>>>>> of documentation so that all add-on overlays will use the same terms.
>>>>>
>>>>> Google search keywords: "Microchip SAMA5D3-EDS"
>>>>>
>>>>> Signed-off-by: Jerry Ray <jerry.ray at microchip.com>
>>>>> ---
>>>>> v5->v6:
>>>>>  - Replaced underscores in names where I can, improving naming.
>>>>> v4->v5:
>>>>>  - patch now applies to v6.0-rc2
>>>>> v3->v4:
>>>>>  - Fixed regulators as necessary to get the board to boot from SD Card.
>>>>> v2->v3:
>>>>>  - Alphabetized pinctrl entries.
>>>>>  - cleaned up a warning in the regulators section.
>>>>>  - License tweaked to 'OR MIT'
>>>>>  - Included Makefile change
>>>>> v1->v2:
>>>>>  - Modified the compatible field in the device tree to reflect Microchip
>>>>>    Ethernet Development System Board.
>>>>> ---
>>>>>  arch/arm/boot/dts/Makefile             |   1 +
>>>>>  arch/arm/boot/dts/at91-sama5d3_eds.dts | 309
>>>>> +++++++++++++++++++++++++
>>>>>  2 files changed, 310 insertions(+)
>>>>>  create mode 100644 arch/arm/boot/dts/at91-sama5d3_eds.dts
>>>>>
>>>>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile 
>>>>> index 05d8aef6e5d2..e92e639a2dc3 100644
>>>>> --- a/arch/arm/boot/dts/Makefile
>>>>> +++ b/arch/arm/boot/dts/Makefile
>>>>> @@ -61,6 +61,7 @@ dtb-$(CONFIG_SOC_SAM_V7) += \
>>>>>       at91-sama5d2_icp.dtb \
>>>>>       at91-sama5d2_ptc_ek.dtb \
>>>>>       at91-sama5d2_xplained.dtb \
>>>>> +     at91-sama5d3_eds.dtb \
>>>>>       at91-sama5d3_ksz9477_evb.dtb \
>>>>>       at91-sama5d3_xplained.dtb \
>>>>>       at91-dvk_som60.dtb \
>>>>> diff --git a/arch/arm/boot/dts/at91-sama5d3_eds.dts
>>>>> b/arch/arm/boot/dts/at91-sama5d3_eds.dts
>>>>> new file mode 100644
>>>>> index 000000000000..b4fe1c5f2997
>>>>> --- /dev/null
>>>>> +++ b/arch/arm/boot/dts/at91-sama5d3_eds.dts
>>>>> @@ -0,0 +1,309 @@
>>>>> +// SPDX-License-Identifier: GPL-2.0+ OR MIT
>>>>> +/*
>>>>> + * at91-sama5d3_eds.dts - Device Tree file for the SAMA5D3 Ethernet
>>>>> + *    Development System board.
>>>>> + *
>>>>> + * Copyright (C) 2022 Microchip Technology Inc. and its 
>>>>> +subsidiaries
>>>>> + *
>>>>> + * Author: Jerry Ray <jerry.ray at microchip.com>  */ /dts-v1/; 
>>>>> +#include "sama5d36.dtsi"
>>>>> +
>>>>> +/ {
>>>>> +     model = "SAMA5D3 Ethernet Development System";
>>>>> +     compatible = "microchip,sama5d3-eds", "atmel,sama5d36",
>>>>> +                  "atmel,sama5d3", "atmel,sama5";
>>>>> +
>>>>> +     chosen {
>>>>> +             stdout-path = "serial0:115200n8";
>>>>> +     };
>>>>> +
>>>>> +     clocks {
>>>>> +             slow_xtal {
>>>>
>>>> No underscores in node names. Override by label.
>>>>
>>>>> +                     clock-frequency = <32768>;
>>>>> +             };
>>>>> +
>>>>> +             main_xtal {
>>>>> +                     clock-frequency = <12000000>;
>>>>> +             };
>>>>> +     };
>>>>> +
>>>>> +     gpio {
>>>>> +             compatible = "gpio-keys";
>>>>> +
>>>>> +             pinctrl-names = "default";
>>>>> +             pinctrl-0 = <&pinctrl_key_gpio>;
>>>>> +
>>>>> +             button-3 {
>>>>> +                     label = "PB_USER";
>>>>> +                     gpios = <&pioE 29 GPIO_ACTIVE_LOW>;
>>>>> +                     linux,code = <0x104>;
>>>>> +                     wakeup-source;
>>>>> +             };
>>>>> +     };
>>>>> +
>>>>> +     memory at 20000000 {
>>>>> +             reg = <0x20000000 0x10000000>;
>>>>> +     };
>>>>> +
>>>>> +     vcc_3v3_reg: buck-regulator-1 {
>>>>
>>>> Keep consistent prefix or suffix, so:
>>>> regulator-buck-1
>>>>
>>>>> +             compatible = "regulator-fixed";
>>>>> +             regulator-name = "VCC_3V3";
>>>>> +             regulator-min-microvolt = <3300000>;
>>>>> +             regulator-max-microvolt = <3300000>;
>>>>> +             regulator-always-on;
>>>>> +     };
>>>>> +
>>>>> +     vcc_2v5_reg: ldo-regulator-2 {
>>>>
>>>> regulator-ldo-1
>>>> (why numbering of LDO regulators starts from 2? keep some sense in 
>>>> this)
>>>>
>>>>
>>>
>>> There are N regulators on the board, so they are numbered 1 thru N.
>>> Regulator 2 is regulator 2 whether it's a buck or LDO.
>>
>> So if this is supposed to match board schematics (which is good idea), then maybe just "regulator-2"? The point is to have same generic name and customize either prefix or suffix, but not both.
>>
>> Best regards,
>> Krzysztof
>>
> 
> I prefer names to be descriptive, but I suppose I can have the name generic and add a comment into the dts file.
> However, the comment doesn't make it into the loaded device tree.  Would you be okay with "regulator-2-ldo"?

You have the descriptive name in the regulator-name property, but ok,
can be in node name as well.




Best regards,
Krzysztof