[PATCH v4 12/13] ARM: dts: rockchip: rv1126: Add Edgeble AI Edge Compute Module 0
Jagan Teki
jagan at edgeble.ai
Wed Sep 7 09:02:06 PDT 2022
Edge Compute Module 0 is a 96boards SoM-CB compute module based
on Rockchip RV1126 from Edgeble AI.
General features:
- Rockchip RV1126
- 2/4GB LPDDR4
- 16GB eMMC
- Fn-link 8223A-SR WiFi/BT
Edge Compute Module 0 needs to mount on top of Edgeble AI Carrier
boards for creating complete platform solutions.
Add support for it.
Signed-off-by: Jagan Teki <jagan at edgeble.ai>
---
Changes for v4:
- rebase on -next
Changes for v3:
- none
Changes for v2:
- change meaninful dtsi name
.../rv1126-edgeble-edge-compute-module-0.dtsi | 353 ++++++++++++++++++
1 file changed, 353 insertions(+)
create mode 100644 arch/arm/boot/dts/rv1126-edgeble-edge-compute-module-0.dtsi
diff --git a/arch/arm/boot/dts/rv1126-edgeble-edge-compute-module-0.dtsi b/arch/arm/boot/dts/rv1126-edgeble-edge-compute-module-0.dtsi
new file mode 100644
index 000000000000..212990d8fb75
--- /dev/null
+++ b/arch/arm/boot/dts/rv1126-edgeble-edge-compute-module-0.dtsi
@@ -0,0 +1,353 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Rockchip Electronics Co., Ltd.
+ * Copyright (c) 2022 Edgeble AI Technologies Pvt. Ltd.
+ */
+
+/ {
+ compatible = "edgeble,edge-compute-module-0", "rockchip,rv1126";
+
+ aliases {
+ mmc0 = &emmc;
+ };
+
+ vcc5v0_sys: vccsys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ vccio_flash: vccio-flash {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpios = <&gpio0 RK_PB3 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&flash_vol_sel>;
+ regulator-name = "vccio_flash";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3>;
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&rk809 1>;
+ clock-names = "ext_clock";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_enable_h>;
+ reset-gpios = <&gpio1 RK_PD0 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&emmc {
+ bus-width = <8>;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_bus8 &emmc_cmd &emmc_clk &emmc_rstnout>;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vccio_flash>;
+ rockchip,default-sample-phase = <90>;
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ rk809: pmic at 20 {
+ compatible = "rockchip,rk809";
+ reg = <0x20>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PB1 IRQ_TYPE_LEVEL_LOW>;
+ #clock-cells = <1>;
+ clock-output-names = "rk808-clkout1", "rk808-clkout2";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int_l>;
+ rockchip,system-power-controller;
+ wakeup-source;
+
+ vcc1-supply = <&vcc5v0_sys>;
+ vcc2-supply = <&vcc5v0_sys>;
+ vcc3-supply = <&vcc5v0_sys>;
+ vcc4-supply = <&vcc5v0_sys>;
+ vcc5-supply = <&vcc_buck5>;
+ vcc6-supply = <&vcc_buck5>;
+ vcc7-supply = <&vcc5v0_sys>;
+ vcc8-supply = <&vcc3v3_sys>;
+ vcc9-supply = <&vcc5v0_sys>;
+
+ regulators {
+ vdd_npu_vepu: DCDC_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <650000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <6001>;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vdd_npu_vepu";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_arm: DCDC_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <725000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vdd_arm";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vcc_ddr";
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc3v3_sys: DCDC_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vcc3v3_sys";
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc_buck5: DCDC_REG5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <2200000>;
+ regulator-max-microvolt = <2200000>;
+ regulator-name = "vcc_buck5";
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <2200000>;
+ };
+ };
+
+ vcc_0v8: LDO_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-name = "vcc_0v8";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc1v8_pmu: LDO_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc1v8_pmu";
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vdd0v8_pmu: LDO_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-name = "vcc0v8_pmu";
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <800000>;
+ };
+ };
+
+ vcc_1v8: LDO_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc_1v8";
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc_dovdd: LDO_REG5 {
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc_dovdd";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_dvdd: LDO_REG6 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc_dvdd";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_avdd: LDO_REG7 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "vcc_avdd";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vccio_sd: LDO_REG8 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vccio_sd";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_sd: LDO_REG9 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc3v3_sd";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_5v0: SWITCH_REG1 {
+ regulator-name = "vcc_5v0";
+ };
+
+ vcc_3v3: SWITCH_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc_3v3";
+ };
+ };
+ };
+};
+
+&pinctrl {
+ bt {
+ bt_enable: bt-enable {
+ rockchip,pins = <3 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ flash {
+ flash_vol_sel: flash-vol-sel {
+ rockchip,pins = <0 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pmic {
+ pmic_int_l: pmic-int-l {
+ rockchip,pins = <0 RK_PB1 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ wifi {
+ wifi_enable_h: wifi-enable-h {
+ rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pmu_io_domains {
+ pmuio0-supply = <&vcc1v8_pmu>;
+ pmuio1-supply = <&vcc3v3_sys>;
+ vccio1-supply = <&vccio_flash>;
+ vccio2-supply = <&vccio_sd>;
+ vccio3-supply = <&vcc_1v8>;
+ vccio4-supply = <&vcc_dovdd>;
+ vccio5-supply = <&vcc_1v8>;
+ vccio6-supply = <&vcc_1v8>;
+ vccio7-supply = <&vcc_dovdd>;
+ status = "okay";
+};
+
+&saradc {
+ vref-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+&sdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ max-frequency = <100000000>;
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cap-sdio-irq;
+ keep-power-in-suspend;
+ mmc-pwrseq = <&sdio_pwrseq>;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc1_clk &sdmmc1_cmd &sdmmc1_bus4>;
+ vmmc-supply = <&vcc3v3_sys>;
+ vqmmc-supply = <&vcc_1v8>;
+ rockchip,default-sample-phase = <90>;
+ sd-uhs-sdr104;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_xfer &uart0_ctsn &uart0_rtsn>;
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,qca9377-bt";
+ clocks = <&rk809 1>;
+ clock-names = "lpo";
+ enable-gpios = <&gpio3 RK_PA5 GPIO_ACTIVE_HIGH>; /* BT_RST */
+ max-speed = <2000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_enable>;
+ vddxo-supply = <&vcc3v3_sys>;
+ vddio-supply = <&vcc_1v8>;
+ };
+};
--
2.25.1
More information about the linux-arm-kernel
mailing list