[PATCH net-next 2/2] ARM: dts: aspeed: elbert: Enable mac3 controller

Tao Ren rentao.bupt at gmail.com
Tue Sep 6 16:35:20 PDT 2022


Hi Florian and Andrew,

On Tue, Sep 06, 2022 at 10:05:46AM -0700, Florian Fainelli wrote:
> 
> 
> On 9/6/2022 4:55 AM, Andrew Lunn wrote:
> > On Mon, Sep 05, 2022 at 06:41:33PM -0700, Tao Ren wrote:
> > > Hi Andrew,
> > > 
> > > On Tue, Sep 06, 2022 at 02:22:50AM +0200, Andrew Lunn wrote:
> > > > On Mon, Sep 05, 2022 at 04:56:34PM -0700, rentao.bupt at gmail.com wrote:
> > > > > From: Tao Ren <rentao.bupt at gmail.com>
> > > > > 
> > > > > Enable mac3 controller in Elbert dts: Elbert MAC3 is connected to the
> > > > > onboard switch directly (fixed link).
> > > > 
> > > > What is the switch? Could you also add a DT node for it?
> > > > 
> > > > > 
> > > > > Signed-off-by: Tao Ren <rentao.bupt at gmail.com>
> > > > > ---
> > > > >   arch/arm/boot/dts/aspeed-bmc-facebook-elbert.dts | 11 +++++++++++
> > > > >   1 file changed, 11 insertions(+)
> > > > > 
> > > > > diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-elbert.dts b/arch/arm/boot/dts/aspeed-bmc-facebook-elbert.dts
> > > > > index 27b43fe099f1..52cb617783ac 100644
> > > > > --- a/arch/arm/boot/dts/aspeed-bmc-facebook-elbert.dts
> > > > > +++ b/arch/arm/boot/dts/aspeed-bmc-facebook-elbert.dts
> > > > > @@ -183,3 +183,14 @@ imux31: i2c at 7 {
> > > > >   &i2c11 {
> > > > >   	status = "okay";
> > > > >   };
> > > > > +
> > > > > +&mac3 {
> > > > > +	status = "okay";
> > > > > +	phy-mode = "rgmii";
> > > > 
> > > > 'rgmii' is suspicious, though not necessarily wrong. This value is
> > > > normally passed to the PHY, so the PHY inserts the RGMII delay. You
> > > > however don't have a PHY. So i assume the switch is inserting the
> > > > delay? Again, being able to see the DT properties for the switch would
> > > > be useful.
> > > > 
> > > >     Andrew
> > > 
> > > Thank you for the quick review!
> > > 
> > > The BMC mac3 is connected to BCM53134P's IMP_RGMII port, and there is no
> > > PHY between BMC MAC and BCM53134P. BCM53134P loads configurations from
> > > its EEPROM when the chip is powered.
> > 
> > So i assume you have the switch RGMII port doing the delays. That is
> > fine.
> > 
> > > Could you please point me an example showing how to describe the switch in
> > > dts? Anyhow I will need to improve the patch description and comments in
> > > v2.
> > 
> > It looks like drivers/net/dsa/b53 does not support this particular
> > switch. You could consider extending the driver. See
> > 
> > Documentation/devicetree/bindings/net/dsa/brcm,b53.yaml
> > 
> > for documentation of the binding.
> 
> Correct the 53134 is not supported at the moment by the b53 driver, however
> it should not be too hard to support it, if you would be willing to add it,
> I would be glad to review patches.
> -- 
> Florian

Thank you for the inputs, and I do have plan to dig into dsa drivers and
work out patches when I get chance, because most FBOSS switches have
onboard switch chips connecting BMC and Host to the front-panel
management port.

Specific to this Elbert platform, we don't have plan to configure
BCM53134 via OpenBMC MDIO (dts), because we expect the switch always
loads configurations from its EEPROM.

I've sent out v2 with more comments in the dts file; could you please
check and let me know if it's reasonable/acceptable? Thank you.


Thanks,

Tao



More information about the linux-arm-kernel mailing list