[PATCH v2 1/1] arm64: dts: tqma8mpql: add USB DR support

[Shawn Guo]

On Wed, Aug 31, 2022 at 09:46:06AM +0200, Alexander Stein wrote:
> Add support for USB DR on USB1 interface. Host/Device detection is done
> using the usb-role-switch connector.
> 
> Signed-off-by: Alexander Stein <alexander.stein at ew.tq-group.com>
> ---
> Changes in v2:
> * Split from previous series
> * For now enable USB OTG only
> 
>  .../freescale/imx8mp-tqma8mpql-mba8mpxl.dts   | 40 +++++++++++++++++++
>  1 file changed, 40 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-tqma8mpql-mba8mpxl.dts b/arch/arm64/boot/dts/freescale/imx8mp-tqma8mpql-mba8mpxl.dts
> index d8ca52976170..b30d75b1fa47 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mp-tqma8mpql-mba8mpxl.dts
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-tqma8mpql-mba8mpxl.dts
> @@ -459,6 +459,37 @@ &usdhc2 {
>  	status = "okay";
>  };
>  
> +&usb3_phy0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usb0>;

Should the pinctrl be in USB controller instead of PHY node?

> +	status = "okay";
> +};
> +
> +&usb3_0 {
> +	fsl,over-current-active-low;
> +	status = "okay";
> +};
> +
> +&usb_dwc3_0 {

These nodes are not in alphabetic order.

> +	/* dual role is implemented, but not a full featured OTG */
> +	hnp-disable;
> +	srp-disable;
> +	adp-disable;
> +	dr_mode = "otg";
> +	usb-role-switch;
> +	role-switch-default-mode = "peripheral";
> +	status = "okay";
> +
> +	connector {
> +		compatible = "gpio-usb-b-connector", "usb-b-connector";
> +		type = "micro";
> +		label = "X29";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_usbcon0>;
> +		id-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
> +	};
> +};
> +
>  &iomuxc {
>  	pinctrl_backlight: backlightgrp {
>  		fsl,pins = <MX8MP_IOMUXC_SAI5_RXFS__GPIO3_IO19		0x14>;
> @@ -666,6 +697,15 @@ pinctrl_uart4: uart4grp {
>  			   <MX8MP_IOMUXC_UART4_TXD__UART4_DCE_TX	0x140>;
>  	};
>  
> +	pinctrl_usbcon0: usb0congrp {
> +		fsl,pins = <MX8MP_IOMUXC_GPIO1_IO10__GPIO1_IO10		0x1c0>;
> +	};
> +
> +	pinctrl_usb0: usb0grp {

pinctrl_usb0 should go before pinctrl_usbcon0?

Shawn

> +		fsl,pins = <MX8MP_IOMUXC_GPIO1_IO13__USB1_OTG_OC	0x1c0>,
> +			   <MX8MP_IOMUXC_GPIO1_IO12__USB1_OTG_PWR	0x1c0>;
> +	};
> +
>  	pinctrl_usdhc2: usdhc2grp {
>  		fsl,pins = <MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK		0x192>,
>  			   <MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD		0x1d2>,
> -- 
> 2.25.1
>