[PATCH v3 3/4] thermal: mediatek: add support for MT8365 SoC

[Amjad Ouled-Ameur]

From: Fabien Parent <fparent at baylibre.com>

MT8365 is similar to the other SoCs supported by the driver. It has only
one bank and 3 actual sensors that can be multiplexed. There is another
one sensor that does not have usable data.

Signed-off-by: Fabien Parent <fparent at baylibre.com>
Signed-off-by: Amjad Ouled-Ameur <aouledameur at baylibre.com>
---
 drivers/thermal/mtk_thermal.c | 68 +++++++++++++++++++++++++++++++++++
 1 file changed, 68 insertions(+)

diff --git a/drivers/thermal/mtk_thermal.c b/drivers/thermal/mtk_thermal.c
index b5b4401249e8..088c388da241 100644
--- a/drivers/thermal/mtk_thermal.c
+++ b/drivers/thermal/mtk_thermal.c
@@ -31,6 +31,7 @@
 #define AUXADC_CON2_V		0x010
 #define AUXADC_DATA(channel)	(0x14 + (channel) * 4)
 
+#define APMIXED_SYS_TS_CON0	0x600
 #define APMIXED_SYS_TS_CON1	0x604
 
 /* Thermal Controller Registers */
@@ -245,6 +246,17 @@ enum mtk_thermal_version {
 /* The calibration coefficient of sensor  */
 #define MT8183_CALIBRATION	153
 
+/* MT8365 */
+#define MT8365_TEMP_AUXADC_CHANNEL 11
+#define MT8365_CALIBRATION 164
+#define MT8365_NUM_CONTROLLER 1
+#define MT8365_NUM_BANKS 1
+#define MT8365_NUM_SENSORS 3
+#define MT8365_NUM_SENSORS_PER_ZONE 3
+#define MT8365_TS1 0
+#define MT8365_TS2 1
+#define MT8365_TS3 2
+
 struct mtk_thermal;
 
 struct thermal_bank_cfg {
@@ -389,6 +401,24 @@ static const int mt7622_mux_values[MT7622_NUM_SENSORS] = { 0, };
 static const int mt7622_vts_index[MT7622_NUM_SENSORS] = { VTS1 };
 static const int mt7622_tc_offset[MT7622_NUM_CONTROLLER] = { 0x0, };
 
+/* MT8365 thermal sensor data */
+static const int mt8365_bank_data[MT8365_NUM_SENSORS] = {
+	MT8365_TS1, MT8365_TS2, MT8365_TS3
+};
+
+static const int mt8365_msr[MT8365_NUM_SENSORS_PER_ZONE] = {
+	TEMP_MSR0, TEMP_MSR1, TEMP_MSR2
+};
+
+static const int mt8365_adcpnp[MT8365_NUM_SENSORS_PER_ZONE] = {
+	TEMP_ADCPNP0, TEMP_ADCPNP1, TEMP_ADCPNP2
+};
+
+static const int mt8365_mux_values[MT8365_NUM_SENSORS] = { 0, 1, 2 };
+static const int mt8365_tc_offset[MT8365_NUM_CONTROLLER] = { 0 };
+
+static const int mt8365_vts_index[MT8365_NUM_SENSORS] = { VTS1, VTS2, VTS3 };
+
 /*
  * The MT8173 thermal controller has four banks. Each bank can read up to
  * four temperature sensors simultaneously. The MT8173 has a total of 5
@@ -463,6 +493,40 @@ static const struct mtk_thermal_data mt2701_thermal_data = {
 	.version = MTK_THERMAL_V1,
 };
 
+/*
+ * The MT8365 thermal controller has one bank, which can read up to
+ * four temperature sensors simultaneously. The MT8365 has a total of 3
+ * temperature sensors.
+ *
+ * The thermal core only gets the maximum temperature of this one bank,
+ * so the bank concept wouldn't be necessary here. However, the SVS (Smart
+ * Voltage Scaling) unit makes its decisions based on the same bank
+ * data.
+ */
+static const struct mtk_thermal_data mt8365_thermal_data = {
+	.auxadc_channel = MT8365_TEMP_AUXADC_CHANNEL,
+	.num_banks = MT8365_NUM_BANKS,
+	.num_sensors = MT8365_NUM_SENSORS,
+	.vts_index = mt8365_vts_index,
+	.cali_val = MT8365_CALIBRATION,
+	.num_controller = MT8365_NUM_CONTROLLER,
+	.controller_offset = mt8365_tc_offset,
+	.need_switch_bank = false,
+	.bank_data = {
+		{
+			.num_sensors = MT8365_NUM_SENSORS,
+			.sensors = mt8365_bank_data
+		},
+	},
+	.msr = mt8365_msr,
+	.adcpnp = mt8365_adcpnp,
+	.sensor_mux_values = mt8365_mux_values,
+	.version = MTK_THERMAL_V1,
+	.apmixed_buffer_ctl_reg = APMIXED_SYS_TS_CON0,
+	.apmixed_buffer_ctl_mask = (u32) ~GENMASK(29, 28),
+	.apmixed_buffer_ctl_set = 0,
+};
+
 /*
  * The MT2712 thermal controller has one bank, which can read up to
  * four temperature sensors simultaneously. The MT2712 has a total of 4
@@ -964,6 +1028,10 @@ static const struct of_device_id mtk_thermal_of_match[] = {
 	{
 		.compatible = "mediatek,mt8183-thermal",
 		.data = (void *)&mt8183_thermal_data,
+	},
+	{
+		.compatible = "mediatek,mt8365-thermal",
+		.data = (void *)&mt8365_thermal_data,
 	}, {
 	},
 };
-- 
2.37.3