[PATCH RESEND 1/6] arm64: dts: ti: k3-j721s2-main: Add support for USB

[Vignesh Raghavendra]

Hi Matt,

On 10/08/22 15:09, Matt Ranostay wrote:
> From: Aswath Govindraju <a-govindraju at ti.com>
> 
> Add support for single instance of USB 3.0 controller in J721S2 SoC.
> 
> Cc: Vignesh Raghavendra <vigneshr at ti.com>
> Cc: Nishanth Menon <nm at ti.com>
> Acked-by: Matt Ranostay <mranostay at ti.com>
> Signed-off-by: Aswath Govindraju <a-govindraju at ti.com>
> ---
>  arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 42 ++++++++++++++++++++++
>  1 file changed, 42 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
> index 34e7d577ae13..f7e359da8690 100644
> --- a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
> @@ -26,6 +26,20 @@ l3cache-sram at 200000 {
>  		};
>  	};
>  
> +	scm_conf: scm-conf at 104000 {

syscon@

> +		compatible = "ti,j721e-system-controller", "syscon", "simple-mfd";
> +		reg = <0x00 0x00104000 0x00 0x18000>;
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges = <0x00 0x00 0x00104000 0x18000>;
> +
> +		usb_serdes_mux: mux-controller at 0 {

mux-controller-0

I see that the mux-controller at 0 node gets renamed to mux-controller at 1 in
2/6. Why not move both to 2/6?

> +			compatible = "mmio-mux";
> +			#mux-control-cells = <1>;
> +			mux-reg-masks = <0x0 0x8000000>; /* USB0 to SERDES0 lane 1/3 mux */
> +		};
> +	};
> +
>  	gic500: interrupt-controller at 1800000 {
>  		compatible = "arm,gic-v3";
>  		#address-cells = <2>;
> @@ -686,6 +700,34 @@ cpts at 310d0000 {
>  		};
>  	};
>  
> +	usbss0: cdns-usb at 4104000 {
> +		compatible = "ti,j721e-usb";
> +		reg = <0x00 0x04104000 0x00 0x100>;
> +		clocks = <&k3_clks 360 16>, <&k3_clks 360 15>;
> +		clock-names = "ref", "lpm";
> +		assigned-clocks = <&k3_clks 360 16>; /* USB2_REFCLK */
> +		assigned-clock-parents = <&k3_clks 360 17>;
> +		power-domains = <&k3_pds 360 TI_SCI_PD_EXCLUSIVE>;
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		ranges;
> +		dma-coherent;
> +
> +		usb0: usb at 6000000 {
> +			compatible = "cdns,usb3";
> +			reg = <0x00 0x06000000 0x00 0x10000>,
> +			      <0x00 0x06010000 0x00 0x10000>,
> +			      <0x00 0x06020000 0x00 0x10000>;
> +			reg-names = "otg", "xhci", "dev";
> +			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "host", "peripheral", "otg";
> +			maximum-speed = "super-speed";
> +			dr_mode = "otg";
> +		};
> +	};
> +
>  	main_mcan0: can at 2701000 {
>  		compatible = "bosch,m_can";
>  		reg = <0x00 0x02701000 0x00 0x200>,

-- 
Regards
Vignesh