[PATCH v3 05/13] ARM: dts: imx6ull-colibri: update usdhc1 pixmux and signaling

Marcel Ziswiler marcel at ziswiler.com
Fri May 6 06:24:08 PDT 2022


From: Philippe Schenker <philippe.schenker at toradex.com>

Due to many carrier boards pulling the usdhc1 signals up to 3.3 volt we
need to disable 1.8 volt signaling. Adding the no-1-8-v property
basically disables UHS-I modes by default.

Also pull-up the command and data lines to the +V3.3_1.8_SD rail and
set them to the 200 MHz speed grade (e.g. pinmux bits 7-6: meaning 11
SPEED_3_max_200MHz).

Explicitly specify a bus-width of <4> in the module-level device tree
include file and drop the no-1-8-v property from the carrier boards
device trees.

Signed-off-by: Philippe Schenker <philippe.schenker at toradex.com>
Signed-off-by: Denys Drozdov <denys.drozdov at toradex.com>
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs at toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler at toradex.com>
---

(no changes since v1)

 .../arm/boot/dts/imx6ull-colibri-eval-v3.dtsi | 14 --------
 arch/arm/boot/dts/imx6ull-colibri.dtsi        | 36 ++++++++++++-------
 2 files changed, 24 insertions(+), 26 deletions(-)

diff --git a/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi b/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi
index a78849fd2afa..ea086b305d22 100644
--- a/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi
+++ b/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi
@@ -159,20 +159,6 @@ &usbotg2 {
 };
 
 &usdhc1 {
-	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
-	pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_snvs_usdhc1_cd>;
-	pinctrl-1 = <&pinctrl_usdhc1_100mhz &pinctrl_snvs_usdhc1_cd>;
-	pinctrl-2 = <&pinctrl_usdhc1_200mhz &pinctrl_snvs_usdhc1_cd>;
-	pinctrl-3 = <&pinctrl_usdhc1 &pinctrl_snvs_usdhc1_sleep_cd>;
-	cd-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
-	disable-wp;
-	wakeup-source;
-	keep-power-in-suspend;
 	vmmc-supply = <&reg_3v3>;
-	vqmmc-supply = <&reg_sd1_vmmc>;
-	sd-uhs-sdr12;
-	sd-uhs-sdr25;
-	sd-uhs-sdr50;
-	sd-uhs-sdr104;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/imx6ull-colibri.dtsi b/arch/arm/boot/dts/imx6ull-colibri.dtsi
index c89b209be316..351ea2acd5a6 100644
--- a/arch/arm/boot/dts/imx6ull-colibri.dtsi
+++ b/arch/arm/boot/dts/imx6ull-colibri.dtsi
@@ -35,7 +35,7 @@ reg_module_3v3_avdd: regulator-module-3v3-avdd {
 		regulator-max-microvolt = <3300000>;
 	};
 
-	reg_sd1_vmmc: regulator-sd1-vmmc {
+	reg_sd1_vqmmc: regulator-sd1-vqmmc {
 		compatible = "regulator-gpio";
 		gpio = <&gpio5 9 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
@@ -232,9 +232,21 @@ &usbotg2 {
 };
 
 &usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_snvs_usdhc1_cd>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz &pinctrl_snvs_usdhc1_cd>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz &pinctrl_snvs_usdhc1_cd>;
+	pinctrl-3 = <&pinctrl_usdhc1 &pinctrl_snvs_usdhc1_sleep_cd>;
 	assigned-clocks = <&clks IMX6UL_CLK_USDHC1_SEL>, <&clks IMX6UL_CLK_USDHC1>;
 	assigned-clock-parents = <&clks IMX6UL_CLK_PLL2_PFD2>;
 	assigned-clock-rates = <0>, <198000000>;
+	bus-width = <4>;
+	cd-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	keep-power-in-suspend;
+	no-1-8-v;
+	vqmmc-supply = <&reg_sd1_vqmmc>;
+	wakeup-source;
 };
 
 &wdog1 {
@@ -550,8 +562,8 @@ MX6UL_PAD_GPIO1_IO02__GPIO1_IO02	0x10b0 /* SODIMM 129 */
 
 	pinctrl_usdhc1: usdhc1-grp {
 		fsl,pins = <
-			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x17059 /* SODIMM 47 */
-			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x10059 /* SODIMM 190 */
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x10059 /* SODIMM 47 */
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x17059 /* SODIMM 190 */
 			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x17059 /* SODIMM 192 */
 			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x17059 /* SODIMM 49 */
 			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x17059 /* SODIMM 51 */
@@ -561,8 +573,8 @@ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x17059 /* SODIMM 53 */
 
 	pinctrl_usdhc1_100mhz: usdhc1-100mhz-grp {
 		fsl,pins = <
-			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x170b9
-			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x100b9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100b9
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170b9
 			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170b9
 			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170b9
 			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170b9
@@ -572,12 +584,12 @@ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170b9
 
 	pinctrl_usdhc1_200mhz: usdhc1-200mhz-grp {
 		fsl,pins = <
-			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x170f9
-			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x100f9
-			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170b9
-			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170b9
-			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170b9
-			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170b9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100f9
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170f9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170f9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170f9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170f9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170f9
 		>;
 	};
 
@@ -588,7 +600,7 @@ MX6UL_PAD_CSI_DATA01__USDHC2_DATA1	0x17069
 			MX6UL_PAD_CSI_DATA02__USDHC2_DATA2	0x17069
 			MX6UL_PAD_CSI_DATA03__USDHC2_DATA3	0x17069
 			MX6UL_PAD_CSI_HSYNC__USDHC2_CMD		0x17069
-			MX6UL_PAD_CSI_VSYNC__USDHC2_CLK		0x17069
+			MX6UL_PAD_CSI_VSYNC__USDHC2_CLK		0x10069
 
 			MX6UL_PAD_GPIO1_IO03__OSC32K_32K_OUT	0x10
 		>;
-- 
2.35.1




More information about the linux-arm-kernel mailing list