[PATCH v5 3/8] hisi_ptt: Register PMU device for PTT trace

[Jonathan Cameron]

On Tue, 8 Mar 2022 19:13:08 +0800
Yicong Yang <yangyicong at huawei.com> wrote:

> On 2022/3/8 18:21, Jonathan Cameron wrote:
> > On Tue, 8 Mar 2022 16:49:25 +0800
> > Yicong Yang <yangyicong at hisilicon.com> wrote:
> >   
> >> Register PMU device of PTT trace, then users can use trace through perf
> >> command. The driver makes use of perf AUX trace and support following
> >> events to configure the trace:
> >>
> >> - filter: select Root port or Endpoint to trace
> >> - type: select the type of traced TLP headers
> >> - direction: select the direction of traced TLP headers
> >> - format: select the data format of the traced TLP headers
> >>
> >> This patch adds the PMU driver part of PTT trace. The perf command support
> >> of PTT trace is added in the following patch.
> >>
> >> Signed-off-by: Yicong Yang <yangyicong at hisilicon.com>  
> > 
> > It seems to me that you ended up doing both suggestions for
> > how to clean up the remove order when it was meant to be
> > a question of picking one or the other.
> > 
> > Otherwise this looks good to me - so with that tidied up
> >   
> 
> Hi Jonathan,
> 
> Thanks for the comments. I'd like to illustrate the reason why I decide to
> manually unregister the PMU device.
> 
> The DMA buffers are devm allocated when necessary. They're only allocated
> when user is going to use the PTT in the first time after the driver's probe,
> so when driver removal the buffers are released prior to the PMU device's
> unregistration. I think there's a race condition.
> 
> IIUC, The PMU device(as the user interface) should be unregistered first then
> we're safe to free the DMA buffers. But unregister the PMU device by devm
> cannot keep that order.

Ok. Please add a comment in the remove() giving this reasoning.

Jonathan

> 
> Thanks,
> Yicong
> 
> > Reviewed-by: Jonathan Cameron <Jonathan.Cameron at huawei.com>
> >   
> >> ---  
> >   
> >> +
> >> +static int hisi_ptt_register_pmu(struct hisi_ptt *hisi_ptt)
> >> +{
> >> +	u16 core_id, sicl_id;
> >> +	char *pmu_name;
> >> +	u32 reg;
> >> +
> >> +	hisi_ptt->hisi_ptt_pmu = (struct pmu) {
> >> +		.module		= THIS_MODULE,
> >> +		.capabilities	= PERF_PMU_CAP_EXCLUSIVE | PERF_PMU_CAP_ITRACE,
> >> +		.task_ctx_nr	= perf_sw_context,
> >> +		.attr_groups	= hisi_ptt_pmu_groups,
> >> +		.event_init	= hisi_ptt_pmu_event_init,
> >> +		.setup_aux	= hisi_ptt_pmu_setup_aux,
> >> +		.free_aux	= hisi_ptt_pmu_free_aux,
> >> +		.start		= hisi_ptt_pmu_start,
> >> +		.stop		= hisi_ptt_pmu_stop,
> >> +		.add		= hisi_ptt_pmu_add,
> >> +		.del		= hisi_ptt_pmu_del,
> >> +	};
> >> +
> >> +	reg = readl(hisi_ptt->iobase + HISI_PTT_LOCATION);
> >> +	core_id = FIELD_GET(HISI_PTT_CORE_ID, reg);
> >> +	sicl_id = FIELD_GET(HISI_PTT_SICL_ID, reg);
> >> +
> >> +	pmu_name = devm_kasprintf(&hisi_ptt->pdev->dev, GFP_KERNEL, "hisi_ptt%u_%u",
> >> +				  sicl_id, core_id);
> >> +	if (!pmu_name)
> >> +		return -ENOMEM;
> >> +
> >> +	return perf_pmu_register(&hisi_ptt->hisi_ptt_pmu, pmu_name, -1);  
> > 
> > As below, you can put back the devm cleanup that you had in v4 now you
> > have modified how the filter cleanup is done to also be devm managed.
> >   
> >> +}
> >> +
> >>  /*
> >>   * The DMA of PTT trace can only use direct mapping, due to some
> >>   * hardware restriction. Check whether there is an IOMMU or the
> >> @@ -303,15 +825,32 @@ static int hisi_ptt_probe(struct pci_dev *pdev,
> >>  
> >>  	pci_set_master(pdev);
> >>  
> >> +	ret = hisi_ptt_register_irq(hisi_ptt);
> >> +	if (ret)
> >> +		return ret;
> >> +
> >>  	ret = hisi_ptt_init_ctrls(hisi_ptt);
> >>  	if (ret) {
> >>  		pci_err(pdev, "failed to init controls, ret = %d.\n", ret);
> >>  		return ret;
> >>  	}
> >>  
> >> +	ret = hisi_ptt_register_pmu(hisi_ptt);
> >> +	if (ret) {
> >> +		pci_err(pdev, "failed to register pmu device, ret = %d", ret);
> >> +		return ret;
> >> +	}
> >> +
> >>  	return 0;
> >>  }
> >>  
> >> +void hisi_ptt_remove(struct pci_dev *pdev)
> >> +{
> >> +	struct hisi_ptt *hisi_ptt = pci_get_drvdata(pdev);
> >> +
> >> +	perf_pmu_unregister(&hisi_ptt->hisi_ptt_pmu);  
> > 
> > Now you have the filter cleanup occurring using a devm_add_action_or_reset()
> > there is no need to have a manual cleanup of this - you can
> > use the approach of a devm_add_action_or_reset like you had in v4.
> > 
> > As it is the last call in the probe() order it will be the first one
> > called in the device managed cleanup.
> >   
> >> +}
> >> +  
> > 
> > 
> > .
> >