[PATCH v7 1/5] dt-bindings: nand: meson: fix meson nfc clock

Liang Yang liang.yang at amlogic.com
Fri Jun 24 06:12:51 PDT 2022


EMMC and NAND have the same clock control register named 'SD_EMMC_CLOCK'
which is defined in EMMC port internally. bit0~5 of 'SD_EMMC_CLOCK' is
the divider and bit6~7 is the mux for fix pll and xtal. At the beginning,
a common MMC and NAND sub-clock was discussed and planed to be implemented
as NFC clock provider, but now this series of patches of a common MMC and
NAND sub-clock are never being accepted and the current binding was never
valid. the reasons for giving up are:
1. EMMC and NAND, which are mutually exclusive anyway
2. coupling the EMMC and NAND.
3. it seems that a common MMC and NAND sub-clock is over engineered.
and let us see the link fot more information:
https://lore.kernel.org/all/20220121074508.42168-5-liang.yang@amlogic.com
so The meson nfc can't work now, let us rework the clock.

Acked-by: Rob Herring <robh at kernel.org>
Signed-off-by: Liang Yang <liang.yang at amlogic.com>
---
 .../bindings/mtd/amlogic,meson-nand.txt       | 29 ++++++++-----------
 1 file changed, 12 insertions(+), 17 deletions(-)

diff --git a/Documentation/devicetree/bindings/mtd/amlogic,meson-nand.txt b/Documentation/devicetree/bindings/mtd/amlogic,meson-nand.txt
index 5794ab1147c1..5d5cdfef417f 100644
--- a/Documentation/devicetree/bindings/mtd/amlogic,meson-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/amlogic,meson-nand.txt
@@ -7,18 +7,19 @@ Required properties:
 - compatible : contains one of:
   - "amlogic,meson-gxl-nfc"
   - "amlogic,meson-axg-nfc"
+
+- reg        : Offset and length of the register set
+
+- reg-names  : "nfc" is the register set for NFC controller and "emmc"
+		is the register set for MCI controller.
+
 - clocks     :
 	A list of phandle + clock-specifier pairs for the clocks listed
 	in clock-names.
 
 - clock-names: Should contain the following:
 	"core" - NFC module gate clock
-	"device" - device clock from eMMC sub clock controller
-	"rx" - rx clock phase
-	"tx" - tx clock phase
-
-- amlogic,mmc-syscon	: Required for NAND clocks, it's shared with SD/eMMC
-				controller port C
+	"device" - parent clock for internal NFC
 
 Optional children nodes:
 Children nodes represent the available nand chips.
@@ -28,24 +29,18 @@ see Documentation/devicetree/bindings/mtd/nand-controller.yaml for generic bindi
 
 Example demonstrate on AXG SoC:
 
-	sd_emmc_c_clkc: mmc at 7000 {
-		compatible = "amlogic,meson-axg-mmc-clkc", "syscon";
-		reg = <0x0 0x7000 0x0 0x800>;
-	};
-
 	nand-controller at 7800 {
 		compatible = "amlogic,meson-axg-nfc";
-		reg = <0x0 0x7800 0x0 0x100>;
+		reg = <0x0 0x7800 0x0 0x100>,
+		      <0x0 0x7000 0x0 0x800>;
+		reg-names = "nfc", "emmc";
 		#address-cells = <1>;
 		#size-cells = <0>;
 		interrupts = <GIC_SPI 34 IRQ_TYPE_EDGE_RISING>;
 
 		clocks = <&clkc CLKID_SD_EMMC_C>,
-			<&sd_emmc_c_clkc CLKID_MMC_DIV>,
-			<&sd_emmc_c_clkc CLKID_MMC_PHASE_RX>,
-			<&sd_emmc_c_clkc CLKID_MMC_PHASE_TX>;
-		clock-names = "core", "device", "rx", "tx";
-		amlogic,mmc-syscon = <&sd_emmc_c_clkc>;
+			 <&clkc CLKID_FCLK_DIV2>;
+		clock-names = "core", "device";
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&nand_pins>;
-- 
2.34.1




More information about the linux-arm-kernel mailing list